[PATCH] net: sun8i-emac: Fix pinmux setup for Allwinner H5

[Andre Przywara]

Commit eb5a2b671075 ("net: sun8i-emac: Determine pinmux based on SoC,
not EMAC type") switched the pinmux setup over to look at
CONFIG_MACH_SUN* symbols, to find the appropriate mux value.
Unfortunately this patch missed to check for the H5, which is
pin-compatible to the H3, but uses a different Kconfig symbol (because
it has ARMv8 vs. ARMv7 cores).

Replace the pure SUN8I_H3 symbol with the joint SUNXI_H3_H5 one, which is
there to cover the peripherals common to both SoCs.
Also explicitly list each supported SoC, and have an error message in the
fallback case, to avoid those problems in the future.

This fixes Ethernet support on all H5 boards.

Signed-off-by: Andre Przywara <andre.p...@arm.com>
---
drivers/net/sun8i_emac.c | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/net/sun8i_emac.c b/drivers/net/sun8i_emac.c
index a6cdda81a76..5a1b38bf80f 100644
--- a/drivers/net/sun8i_emac.c
+++ b/drivers/net/sun8i_emac.c
@@ -554,7 +554,7 @@ static int parse_phy_pins(struct udevice *dev)
* The GPIO pinmux value is an integration choice, so depends on the
* SoC, not the EMAC variant.
*/
- if (IS_ENABLED(CONFIG_MACH_SUN8I_H3))
+ if (IS_ENABLED(CONFIG_MACH_SUNXI_H3_H5))
iomux = SUN8I_IOMUX_H3;
else if (IS_ENABLED(CONFIG_MACH_SUN8I_R40))
iomux = SUN8I_IOMUX_R40;
@@ -562,8 +562,12 @@ static int parse_phy_pins(struct udevice *dev)
iomux = SUN8I_IOMUX_H6;
else if (IS_ENABLED(CONFIG_MACH_SUN50I_H616))
iomux = SUN8I_IOMUX_H616;
- else
+ else if (IS_ENABLED(CONFIG_MACH_SUN8I_A83T))
+ iomux = SUN8I_IOMUX;
+ else if (IS_ENABLED(CONFIG_MACH_SUN50I))
iomux = SUN8I_IOMUX;
+ else
+ BUILD_BUG_ON_MSG(1, "missing pinmux value for Ethernet pins");

for (i = 0; ; i++) {
int pin;
--
2.17.5

[Samuel Holland]

On 4/16/21 6:05 AM, Andre Przywara wrote:
> Commit eb5a2b671075 ("net: sun8i-emac: Determine pinmux based on SoC,
> not EMAC type") switched the pinmux setup over to look at
> CONFIG_MACH_SUN* symbols, to find the appropriate mux value.
> Unfortunately this patch missed to check for the H5, which is
> pin-compatible to the H3, but uses a different Kconfig symbol (because
> it has ARMv8 vs. ARMv7 cores).
>
> Replace the pure SUN8I_H3 symbol with the joint SUNXI_H3_H5 one, which is
> there to cover the peripherals common to both SoCs.
> Also explicitly list each supported SoC, and have an error message in the
> fallback case, to avoid those problems in the future.
>
> This fixes Ethernet support on all H5 boards.
>
> Signed-off-by: Andre Przywara <andre.p...@arm.com>

Tested-by: Samuel Holland <sam...@sholland.org> # Orange Pi PC2

Also tested on H3 (Orange Pi Plus 2E) and A64 (Orange Pi Win) to verify
no regression.