HDMi Output on OrangePi Win/Win Plus Allwinner A64 (SUN50I)

gorl...@gmail.com

unread,

Aug 14, 2020, 6:24:17 AM8/14/20

to linux-sunxi

Hello.

Need help to enable HDMI output on u-boot load.

At current time HDMI output work only after linux kernel is loaded. At u-boot time HDMI output is blank (no signal on monitor)
.I try some option like

setenv video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=1
setenv video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=1,edid=1
setenv video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=0
setenv video-mode=sunxi:1024x768-24@60,monitor=hdmi,hpd=0,edid=1
setenv video-mode=sunxi:1024x768-24@60,monitor=hdmi,hpd=1,edid=1
setenv video-mode=sunxi:1024x768-24@60,monitor=hdmi,hpd=0,edid=0

and

setenv hdmi.audio=EDID:0 disp.screen0_output_mode=1024x768p60

setenv hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:1024x768p60

Full output of U-BOOT load
===

U-Boot SPL 2020.07-STLK1-dirty (Aug 14 2020 - 02:43:26 +0300)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.3(debug):v2.3-420-gf0b1864f8
NOTICE: BL31: Built : 15:05:30, Jul 31 2020
NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689)
NOTICE: BL31: Found U-Boot DTB at 0x4099690, model: OrangePi Win/Win Plus
INFO:    ARM GICv2 driver initialized
INFO:    Configuring SPC Controller
INFO:    PMIC: Probing AXP803 on RSB
INFO:    PMIC: dcdc1 voltage: 3.300V
INFO:    PMIC: dcdc5 voltage: 1.500V
INFO:    PMIC: dcdc6 voltage: 1.100V
INFO:    PMIC: dldo1 voltage: 3.300V
INFO:    PMIC: dldo2 voltage: 3.300V
INFO:    PMIC: dldo4 voltage: 3.300V
INFO:    BL31: Platform setup done
INFO:    BL31: Initializing runtime services
INFO:    BL31: cortex_a53: CPU workaround for 843419 was applied
INFO:    BL31: cortex_a53: CPU workaround for 855873 was applied
NOTICE: PSCI: System suspend is unavailable
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x4a000000
INFO:    SPSR = 0x3c9
alloc space exhausted

U-Boot 2020.07-STLK1-dirty (Aug 14 2020 - 02:43:26 +0300) Allwinner Technology

CPU:   Allwinner A64 (SUN50I)
Model: OrangePi Win/Win Plus
DRAM: 2 GiB
MMC:   mmc@1c0f000: 0, mmc@1c10000: 1
Loading Environment from FAT... Card did not respond to voltage select!
In:    serial
Out:   serial
Err:   serial
Model: OrangePi Win/Win Plus
Net:   phy interface7
eth0: ethernet@1c30000
starting USB...
Bus usb@1c1a000: USB EHCI 1.00
Bus usb@1c1a400: USB OHCI 1.0
Bus usb@1c1b000: USB EHCI 1.00
Bus usb@1c1b400: USB OHCI 1.0
scanning bus usb@1c1a000 for devices... 1 USB Device(s) found
scanning bus usb@1c1a400 for devices... 1 USB Device(s) found
scanning bus usb@1c1b000 for devices... 1 USB Device(s) found
scanning bus usb@1c1b400 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Autoboot in 2 seconds, press <Space> to stop
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
3098 bytes read in 2 ms (1.5 MiB/s)
## Executing script at 4fc00000
U-boot loaded from SD
Boot script loaded from mmc
104 bytes read in 2 ms (50.8 KiB/s)
39702 bytes read in 5 ms (7.6 MiB/s)
3821 bytes read in 5 ms (746.1 KiB/s)
Applying kernel provided DT fixup script (sun50i-a64-fixup.scr)
## Executing script at 44000000
11888288 bytes read in 550 ms (20.6 MiB/s)
17162752 bytes read in 818 ms (20 MiB/s)
## Loading init Ramdisk from Legacy Image at 4fe00000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    11888224 Bytes = 11.3 MiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 4fa00000
   Booting using the fdt blob at 0x4fa00000
EHCI failed to shut down host controller.
   Loading Ramdisk to 494a9000, end 49fff660 ... OK
   Loading Device Tree to 0000000049436000, end 00000000494a8fff ... OK

Starting kernel ...

Milos Ladni

unread,

Aug 19, 2020, 5:32:58 AM8/19/20

to linux-sunxi

Hi, i do this few weeks ago for LVDS display...

What i did in u-boot configuration:

CONFIG_VIDEO_SUNXI=y
# CONFIG_VIDEO_HDMI is not set
# CONFIG_VIDEO_VGA is not set
# CONFIG_VIDEO_COMPOSITE is not set

CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:24,pclk_khz:51000,le:319,ri:4,up:34,lo:2,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=1
CONFIG_VIDEO_LCD_POWER="PH9"
CONFIG_VIDEO_LCD_RESET=""
CONFIG_VIDEO_LCD_BL_EN="PH8"
CONFIG_VIDEO_LCD_BL_PWM=""
# CONFIG_VIDEO_LCD_BL_PWM_ACTIVE_LOW is not set
# CONFIG_VIDEO_LCD_PANEL_I2C is not set
CONFIG_VIDEO_LCD_IF_LVDS=y
# CONFIG_VIDEO_LCD_PANEL_PARALLEL is not set

CONFIG_VIDEO_LCD_PANEL_LVDS=y

You should enable HDMI instead of my LVDS display and set correct times...

Milos Ladicorbic

Milos Ladni

unread,

Aug 19, 2020, 5:34:14 AM8/19/20

to linux-sunxi

I forgot to mention that i am using A20 SoC but it should be similar.

Anton Gorlov

unread,

Aug 21, 2020, 9:24:29 AM8/21/20

to linux...@googlegroups.com

Hi!
what version of the u-boot are you using?

19.08.2020 12:34, Milos Ladni пишет:

> --
> You received this message because you are subscribed to the Google
> Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send
> an email to linux-sunxi...@googlegroups.com
> <mailto:linux-sunxi...@googlegroups.com>.
> To view this discussion on the web, visit
> https://groups.google.com/d/msgid/linux-sunxi/a3af45bc-2f17-45e1-a48f-389403e8f038o%40googlegroups.com
> <https://groups.google.com/d/msgid/linux-sunxi/a3af45bc-2f17-45e1-a48f-389403e8f038o%40googlegroups.com?utm_medium=email&utm_source=footer>.

A. Gorlov

unread,

Aug 31, 2020, 3:16:13 AM8/31/20

to linux-sunxi

In u-boot version v2020.07 CONFIG_VIDEO_SUNXI replaced by

CONFIG_SUNXI_DE2=y
CONFIG_VIDEO_DE2=y

in my config I enabled this options already... but HDMI is blank

ср, 19 авг. 2020 г. в 12:34, Milos Ladni <milosla...@gmail.com>:

--

You received this message because you are subscribed to the Google Groups "linux-sunxi" group.

To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi...@googlegroups.com.
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/a3af45bc-2f17-45e1-a48f-389403e8f038o%40googlegroups.com.

Jernej Škrabec

unread,

Aug 31, 2020, 3:35:24 PM8/31/20

to linux...@googlegroups.com, linux-sunxi, gorl...@gmail.com

Dne ponedeljek, 31. avgust 2020 ob 09:10:00 CEST je A. Gorlov napisal(a):

> In u-boot version v2020.07 CONFIG_VIDEO_SUNXI replaced by
> CONFIG_SUNXI_DE2=y
> CONFIG_VIDEO_DE2=y
>
> in my config I enabled this options already... but HDMI is blank

Because HDMI voltage regulator is not enabled. Currently there is no way to do
that in U-Boot (no AXP803 driver). That's why above options are not enabled by
default. You can probably hack ATF to do that...

Best regards,
Jernej

> > <https://groups.google.com/d/msgid/linux-sunxi/a3af45bc-2f17-45e1-a48f-38
> > 9403e8f038o%40googlegroups.com?utm_medium=email&utm_source=footer> .

Anton Gorlov

unread,

Dec 22, 2020, 12:34:29 PM12/22/20

to linux...@googlegroups.com

31.08.2020 22:35, Jernej Škrabec пишет:

> Because HDMI voltage regulator is not enabled. Currently there is no way to do
> that in U-Boot (no AXP803 driver). That's why above options are not enabled by
> default. You can probably hack ATF to do that..

Hello. Patch from
https://lists.denx.de/pipermail/u-boot/2016-December/276684.html
not correct and not working?

Reply all

Reply to author

Forward