HDMI OUTPUT on OrangePi Win/Win Plus Allwinner A64 (SUN50I)

[A. Gorlov]

Hello.

Need help to enable HDMI output on  OrangePi Win/Win Plus Allwinner A64 (SUN50I) platform at u-boot load.

At curernt time HDMI  output work only after linux kernel is loaded. At U-BOOT HDMI is blank (no signal on monitor).

After linux kernel is loaded - monitor is alived.

 

I try some options in boot.scr withnout effect for u-boot:

setenv video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=1

setenv  video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=1,edid=1

setenv  video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=0

setenv  video-mode=sunxi:1024x768-24@60,monitor=hdmi,hpd=0,edid=1

setenv  video-mode=sunxi:1024x768-24@60,monitor=hdmi,hpd=1,edid=1

setenv  video-mode=sunxi:1024x768-24@60,monitor=hdmi,hpd=0,edid=0

and

setenv  hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:1024x768p60

Full  output from U-BOOT

U-Boot SPL 2020.07-STLK1-dirty (Aug 14 2020 - 02:43:26 +0300)                                                                                   
DRAM: 2048 MiB                                                                                                                                  
Trying to boot from MMC1                                                                                                                        
NOTICE:  BL31: v2.3(debug):v2.3-420-gf0b1864f8                                                                                                  
NOTICE:  BL31: Built : 15:05:30, Jul 31 2020                                                                                                    
NOTICE:  BL31: Detected Allwinner A64/H64/R18 SoC (1689)                                                                                        
NOTICE:  BL31: Found U-Boot DTB at 0x4099690, model: OrangePi Win/Win Plus                                                                      
INFO:    ARM GICv2 driver initialized                                                                                                           
INFO:    Configuring SPC Controller                                                                                                             
INFO:    PMIC: Probing AXP803 on RSB                                                                                                            
INFO:    PMIC: dcdc1 voltage: 3.300V                                                                                                            
INFO:    PMIC: dcdc5 voltage: 1.500V                                                                                                            
INFO:    PMIC: dcdc6 voltage: 1.100V                                                                                                            
INFO:    PMIC: dldo1 voltage: 3.300V                                                                                                            
INFO:    PMIC: dldo2 voltage: 3.300V                                                                                                            
INFO:    PMIC: dldo4 voltage: 3.300V                                                                                                            
INFO:    BL31: Platform setup done                                                                                                              
INFO:    BL31: Initializing runtime services                                                                                                    
INFO:    BL31: cortex_a53: CPU workaround for 843419 was applied                                                                                
INFO:    BL31: cortex_a53: CPU workaround for 855873 was applied                                                                                
NOTICE:  PSCI: System suspend is unavailable                                                                                                    
INFO:    BL31: Preparing for EL3 exit to normal world                                                                                           
INFO:    Entry point address = 0x4a000000                                                                                                       
INFO:    SPSR = 0x3c9                                                                                                                           
alloc space exhausted                                                                                                                           


U-Boot 2020.07-STLK1-dirty (Aug 14 2020 - 02:43:26 +0300) Allwinner Technology                                                                  

CPU:   Allwinner A64 (SUN50I)                                                                                                                   
Model: OrangePi Win/Win Plus                                                                                                                    
DRAM:  2 GiB                                                                                                                                    
MMC:   mmc@1c0f000: 0, mmc@1c10000: 1                                                                                                           
Loading Environment from FAT... Card did not respond to voltage select!                                                                         
In:    serial                                                                                                                                   
Out:   serial                                                                                                                                   
Err:   serial                                                                                                                                   
Model: OrangePi Win/Win Plus                                                                                                                    
Net:   phy interface7                                                                                                                           
eth0: ethernet@1c30000                                                                                                                          
starting USB...                                                                                                                                 
Bus usb@1c1a000: USB EHCI 1.00                                                                                                                  
Bus usb@1c1a400: USB OHCI 1.0                                                                                                                   
Bus usb@1c1b000: USB EHCI 1.00                                                                                                                  
Bus usb@1c1b400: USB OHCI 1.0                                                                                                                   
scanning bus usb@1c1a000 for devices... 1 USB Device(s) found                                                                                   
scanning bus usb@1c1a400 for devices... 1 USB Device(s) found                                                                                   
scanning bus usb@1c1b000 for devices... 1 USB Device(s) found                                                                                   
scanning bus usb@1c1b400 for devices... 1 USB Device(s) found                                                                                   
       scanning usb for storage devices... 0 Storage Device(s) found                                                                            
Autoboot in 2 seconds, press <Space> to stop                                                                                                    
switch to partitions #0, OK                                                                                                                     
mmc0 is current device                                                                                                                          
Scanning mmc 0:1...                                                                                                                             
Found U-Boot script /boot/boot.scr                                                                                                              
3098 bytes read in 2 ms (1.5 MiB/s)                                                                                                             
## Executing script at 4fc00000                                                                                                                 
U-boot loaded from SD                                                                                                                           
Boot script loaded from mmc                                                                                                                     
104 bytes read in 1 ms (101.6 KiB/s)                                                                                                            
39702 bytes read in 5 ms (7.6 MiB/s)                                                                                                            
3821 bytes read in 5 ms (746.1 KiB/s)                                                                                                           
Applying kernel provided DT fixup script (sun50i-a64-fixup.scr)                                                                                 
## Executing script at 44000000                                                                                                                 
11888288 bytes read in 548 ms (20.7 MiB/s)                                                                                                      
17162752 bytes read in 816 ms (20.1 MiB/s)                                                                                                      
## Loading init Ramdisk from Legacy Image at 4fe00000 ...                                                                                       
   Image Name:   uInitrd                                                                                                                        
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)                                                                                  
   Data Size:    11888224 Bytes = 11.3 MiB                                                                                                      
   Load Address: 00000000                                                                                                                       
   Entry Point:  00000000                                                                                                                       
   Verifying Checksum ... OK                                                                                                                    
## Flattened Device Tree blob at 4fa00000                                                                                                       
   Booting using the fdt blob at 0x4fa00000                                                                                                     
EHCI failed to shut down host controller.                                                                                                       
   Loading Ramdisk to 494a9000, end 49fff660 ... OK                                                                                             
   Loading Device Tree to 0000000049436000, end 00000000494a8fff ... OK                                                                         

Starting kernel ...