How cheaply could you DIY a high-vacuum pump...

[Mac Cowell]

Thought experiment: what is the lower bound on the cost of making a DIY high-vaccum pump, say with a budget around $500?

Let's define "High vacuum" as 100 mPa - 0.05 mPa.

Jürgen Gross provides a good introduction to the vacuum ranges and requisite pumps used to create them for Mass Spec in "Mass Spectrometry: Ch4 Instrumentation" (Springer, libgen).

In "Working in a Vacuum" (The Amateur Scientist. Sept 1996. Scientific American), Shawn Carlson described the construction of DIY sorption pump that was surely less than $500 in materials and could reach ~1.33 Pa (still a couple of orders of magnitude away from High vac):

"For many applications, sorption pumps are the vehicles of choice for creating a good vacuum. They have no moving parts; instead they work by chilling a type of substance, called a sorbent, to a temperature at which it absorbs gases. Activated charcoal works, but a molecular sieve is better. Molecular sieves are little pellets with so many microscopic nooks and crannies that they have fantastically large surface areas; a one-gram pellet may have more than 1,000 square meters of surface.

When chilled, air molecules get caught in these microchasms. A 50-gram supply can pump a one-liter volume down to 10 millitorr in 20 minutes. (Atmospheric pressure is about 760 torr.) Half a gallon of molecular sieve from Duniway Stockroom sells for about $35."

In the chapter "A Homemade Atom Smasher" (pdf) in "The Scientific American Book of Projects for the Amateur Scientists" (libgen), Clair Stong describes a DIY high-vacuum system based on salvaged refrigerator pumps and a home-made mercury (!) diffusion pump that can reach around 2 mPa. It is unclear how much the entire setup cost but Stong implies that it was around $50-100 in 1960, or $400-800 today.

Lastly, Stephen Hansen hosts a lot of information on DIY vacuum systems at belljar.net. Of particular note is a pdf of correspondence he shared with Frank Lee on Homemade Oil Diffusion Pumps. The file includes a basic design Lee reckons could have been machined in 1965 for $10 (~$80 today) that would reach 5x10^-6 torr, or 0.666 mPa.

Oh, and he also hosts a short article that might be of interest to some: "Home Built Mass Spectrometers - the Development of a Simple Quadrupole Gas Analyzer" (Carl Helber. The Bell Jar Vol.6 No.2 Spring 1997)

I'm curious to know if anyone has more elegant solutions for high vacuum systems.

Mac

[Simon Quellen Field]

Here's a sorption pump for $175.

-----

Get a free science project every week! "http://scitoys.com/newsletter.html"

--
-- You received this message because you are subscribed to the Google Groups DIYbio group. To post to this group, send email to diy...@googlegroups.com. To unsubscribe from this group, send email to diybio+un...@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/diybio?hl=en
Learn more at www.diybio.org
---
You received this message because you are subscribed to the Google Groups "DIYbio" group.
To unsubscribe from this group and stop receiving emails from it, send an email to diybio+un...@googlegroups.com.
To post to this group, send email to diy...@googlegroups.com.
Visit this group at https://groups.google.com/group/diybio.
To view this discussion on the web visit https://groups.google.com/d/msgid/diybio/CA%2BiLdW2pRM5bwRvgphoiAQd1G-z3REtJwkCPpSjkhx8wbg7y1Q%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.

[August Pamplona]

https://hackaday.io/project/8171-everymans-turbomolecular-pump

        Would the above be relevant? 

August

[Nathan McCorkle]

>
> https://hackaday.io/project/8171-everymans-turbomolecular-pump
> Would the above be relevant?
>
> August

Also, on fusor.net there are many discussions and plans/schematics for
turbo pump controllers, so you can buy a used pump (those lacking
controllers are usually much cheaper, as little as $100 or $200)

i.e.
http://www.fusor.net/board/viewtopic.php?f=10&t=4036&start=30