brick house electrician recomendaton?

已查看 17 次
跳至第一个未读帖子

Chris Weiss

未读,
2016年9月24日 19:40:302016/9/24
收件人 Arch Reactor
I have a wall switch that's inside a brick wall that has a shorted wire.  anyone know someone that knows how to fix that without having a surface mount conduit?  

Tony Strawhun

未读,
2016年9月24日 21:22:032016/9/24
收件人 arch-r...@googlegroups.com

Only other option I know of is to attach new wire to the end of your existing wire and use the existing wire to fish the new wire through the wall. Not easy if there was wire anchors or clips installed...but better than trying to fish tape guide new wire through


On Sep 24, 2016 18:40, "Chris Weiss" <cwe...@gmail.com> wrote:
I have a wall switch that's inside a brick wall that has a shorted wire.  anyone know someone that knows how to fix that without having a surface mount conduit?  

--
You received this message because you are subscribed to the Google Groups "Arch Reactor" group.
To unsubscribe from this group and stop receiving emails from it, send an email to arch-reactor+unsubscribe@googlegroups.com.
To post to this group, send email to arch-r...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/arch-reactor/CAEhO07OTrHZUqLuKdL_Nb3skA%3DYwehs5uAO_nkp2-aMEcp3wQw%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.

Chris Weiss

未读,
2016年9月24日 23:17:472016/9/24
收件人 Arch Reactor
Also pretty sure it's in flex conduit in the brick, which doesn't pull or fish well.  At least I don't know the trick to it.

Jim S

未读,
2016年9月26日 12:48:522016/9/26
收件人 Arch Reactor
I would check both ends of the run carefully as it is likely the issue is there unless it's new construction.  Is this new or old wiring?  If it's really old is the insulation cracking?  Fishing new wire can be a very time intensive thing so if you can avoid that by putting some sleeving on the end or something like that it would be a lot less trouble. 

You could find the location using a TDR (Time Domain Reflectometer).  They make expensive equipment to do it but a signal generator and a scope is basically what they are and will work fine.  You send a pulse down the wire, it is reflected back at the short and you time between the transmitted edge and returning reflection.  Not as complicated as it sounds and I have found the location of several issues that way.  Probably are some youtube videos on how to do it...

Chris Weiss

未读,
2016年9月26日 13:23:022016/9/26
收件人 Arch Reactor
it's very old wiring, the insulation looks ok where I can see, so I suspect it's where the metal box clamps on the wire.  there's 2 switches for lights branched off the same run, and I do see a 3V voltage difference between them, but I wrote that off to one having a bulb and the other not, but I don't know if that's right.

I hadn't considered sleeving it, I might try that even though I can't see any issue.  cheap to try, thanks for that suggestion

--
You received this message because you are subscribed to the Google Groups "Arch Reactor" group.
To unsubscribe from this group and stop receiving emails from it, send an email to arch-reactor...@googlegroups.com.

To post to this group, send email to arch-r...@googlegroups.com.
回复全部
回复作者
转发
0 个新帖子