[PATCH sunxi-boards 1/3] h3: Add fex file for Orange Pi PC

[Siarhei Siamashka]

Extracted from the Lubuntu_1404_For_OrangePiPC_v0_8_0_.img.xz image:
http://www.orangepi.org/downloadresources/orangepipc/oragepipc_4a0e8d960f7f0a52606dfaba58.html

Not necessarily the best one, but at least it comes from the
board manufacturer and may be used as a starting point for
further improvements.

Signed-off-by: Siarhei Siamashka <siarhei....@gmail.com>
---
sys_config/h3/xunlong_orange_pi_pc.fex | 814 +++++++++++++++++++++++++++++++++
1 file changed, 814 insertions(+)
create mode 100644 sys_config/h3/xunlong_orange_pi_pc.fex

diff --git a/sys_config/h3/xunlong_orange_pi_pc.fex b/sys_config/h3/xunlong_orange_pi_pc.fex
new file mode 100644
index 0000000..93e8c4c
--- /dev/null
+++ b/sys_config/h3/xunlong_orange_pi_pc.fex
@@ -0,0 +1,814 @@
+[product]
+version = "100"
+machine = "orangepi-plus"
+
+[platform]
+debug_mode = 1
+eraseflag = 1
+next_work = 2
+
+[target]
+#boot_clock = 1008
+boot_clock = 1200
+storage_type = -1
+
+[key_detect_en]
+keyen_flag = 0
+
+[fel_key]
+fel_key_max = 7
+fel_key_min = 2
+
+[card_boot]
+logical_start = 40960
+sprite_work_delay = 500
+sprite_err_delay = 200
+sprite_gpio0 = port:PA15<1><default><default><default>
+next_work = 3
+
+[box_start_os]
+used = 1
+start_type = 1
+irkey_used = 1
+pmukey_used = 1
+pmukey_num = 3
+led_power = 0
+led_state = 0
+
+[boot_init_gpio]
+used = 1
+gpio0 = port:PA15<1><default><default><1>
+gpio1 = port:PG11<1><default><default><1>
+
+[recovery_para]
+used = 1
+mode = 2
+recovery_key = port:PL04<0><default><default><default>
+
+[pm_para]
+standby_mode = 1
+
+[card0_boot_para]
+card_ctrl = 0
+card_high_speed = 1
+card_line = 4
+sdc_d1 = port:PF00<2><1><2><default>
+sdc_d0 = port:PF01<2><1><2><default>
+sdc_clk = port:PF02<2><1><2><default>
+sdc_cmd = port:PF03<2><1><2><default>
+sdc_d3 = port:PF04<2><1><2><default>
+sdc_d2 = port:PF05<2><1><2><default>
+
+[card2_boot_para]
+card_ctrl = 2
+card_high_speed = 1
+card_line = 8
+sdc_cmd = port:PC06<3><1><2><default>
+sdc_clk = port:PC05<3><1><2><default>
+sdc_d0 = port:PC08<3><1><2><default>
+sdc_d1 = port:PC09<3><1><2><default>
+sdc_d2 = port:PC10<3><1><2><default>
+sdc_d3 = port:PC11<3><1><2><default>
+sdc_d4 = port:PC12<3><1><2><default>
+sdc_d5 = port:PC13<3><1><2><default>
+sdc_d6 = port:PC14<3><1><2><default>
+sdc_d7 = port:PC15<3><1><2><default>
+sdc_2xmode = 1
+sdc_ddrmode = 1
+
+[twi_para]
+twi_port = 0
+twi_scl = port:PA11<2><default><default><default>
+twi_sda = port:PA12<2><default><default><default>
+
+[uart_para]
+uart_debug_port = 0
+uart_debug_tx = port:PA04<2><1><default><default>
+uart_debug_rx = port:PA05<2><1><default><default>
+
+[force_uart_para]
+force_uart_port = 0
+force_uart_tx = port:PF02<3><1><default><default>
+force_uart_rx = port:PF04<3><1><default><default>
+
+[jtag_para]
+jtag_enable = 0
+jtag_ms = port:PA00<3><default><default><default>
+jtag_ck = port:PA01<3><default><default><default>
+jtag_do = port:PA02<3><default><default><default>
+jtag_di = port:PA03<3><default><default><default>
+
+[clock]
+pll_video = 297
+pll_ve = 402
+pll_periph0 = 600
+pll_gpu = 576
+pll_periph1 = 600
+pll_de = 864
+
+[dram_para]
+dram_clk = 672
+dram_type = 3
+dram_zq = 0x3b3bfb
+dram_odt_en = 1
+dram_para1 = 283377664
+dram_para2 = 0
+dram_mr0 = 6208
+dram_mr1 = 64
+dram_mr2 = 24
+dram_mr3 = 2
+dram_tpr0 = 0x48a192
+dram_tpr1 = 0x1c2418d
+dram_tpr2 = 0x76051
+dram_tpr3 = 0x0
+dram_tpr4 = 0x0
+dram_tpr5 = 0x0
+dram_tpr6 = 0x64
+dram_tpr7 = 0x0
+dram_tpr8 = 0x0
+dram_tpr9 = 0x0
+dram_tpr10 = 0x0
+dram_tpr11 = 0x6aaa0000
+dram_tpr12 = 0x7979
+dram_tpr13 = 0x800800
+
+[wakeup_src_para]
+cpu_en = 0
+cpu_freq = 48
+pll_ratio = 273
+dram_selfresh_en = 1
+dram_freq = 36
+wakeup_src0 =
+wakeup_src_wl = port:PG10<4><default><default><0>
+
+[twi0]
+twi_used = 1
+twi_scl = port:PA11<2><default><default><default>
+twi_sda = port:PA12<2><default><default><default>
+
+[twi1]
+twi_used = 0
+twi_scl = port:PA18<3><default><default><default>
+twi_sda = port:PA19<3><default><default><default>
+
+[twi2]
+twi_used = 0
+twi_scl = port:PE12<3><default><default><default>
+twi_sda = port:PE13<3><default><default><default>
+
+[uart0]
+uart_used = 1
+uart_port = 0
+uart_type = 2
+uart_tx = port:PA04<2><1><default><default>
+uart_rx = port:PA05<2><1><default><default>
+
+[uart1]
+uart_used = 0
+uart_port = 1
+uart_type = 4
+uart_tx = port:PG06<2><1><default><default>
+uart_rx = port:PG07<2><1><default><default>
+uart_rts = port:PG08<2><1><default><default>
+uart_cts = port:PG09<2><1><default><default>
+
+[uart2]
+uart_used = 0
+uart_port = 2
+uart_type = 4
+uart_tx = port:PA00<2><1><default><default>
+uart_rx = port:PA01<2><1><default><default>
+uart_rts = port:PA02<2><1><default><default>
+uart_cts = port:PA03<2><1><default><default>
+
+[uart3]
+uart_used = 0
+uart_port = 3
+uart_type = 4
+uart_tx = port:PA13<3><1><default><default>
+uart_rx = port:PA14<3><1><default><default>
+uart_rts = port:PA15<3><1><default><default>
+uart_cts = port:PA16<3><1><default><default>
+
+[spi0]
+spi_used = 0
+spi_cs_bitmap = 1
+spi_mosi = port:PC00<3><default><default><default>
+spi_miso = port:PC01<3><default><default><default>
+spi_sclk = port:PC02<3><default><default><default>
+spi_cs0 = port:PC03<3><1><default><default>
+
+[spi1]
+spi_used = 0
+spi_cs_bitmap = 1
+spi_cs0 = port:PA13<2><1><default><default>
+spi_sclk = port:PA14<2><default><default><default>
+spi_mosi = port:PA15<2><default><default><default>
+spi_miso = port:PA16<2><default><default><default>
+
+[spi_devices]
+spi_dev_num = 1
+
+[spi_board0]
+modalias = "m25p32"
+max_speed_hz = 33000000
+bus_num = 0
+chip_select = 0
+mode = 0
+
+[gpio_para]
+gpio_used = 1
+gpio_num = 30
+gpio_pin_1 = port:PL10<1><default><default><1>
+gpio_pin_2 = port:PA15<1><default><default><0>
+gpio_pin_3 = port:PA12<1><default><default><0>
+gpio_pin_4 = port:PA11<1><default><default><0>
+gpio_pin_5 = port:PA06<1><default><default><0>
+gpio_pin_6 = port:PA13<1><default><default><0>
+gpio_pin_7 = port:PA14<1><default><default><0>
+gpio_pin_8 = port:PA01<1><default><default><0>
+gpio_pin_9 = port:PD14<1><default><default><0>
+gpio_pin_10 = port:PA00<1><default><default><0>
+gpio_pin_11 = port:PA03<1><default><default><0>
+gpio_pin_12 = port:PC04<1><default><default><0>
+gpio_pin_13 = port:PC07<1><default><default><0>
+gpio_pin_14 = port:PC00<1><default><default><0>
+gpio_pin_15 = port:PC01<1><default><default><0>
+gpio_pin_16 = port:PA02<1><default><default><0>
+gpio_pin_17 = port:PC02<1><default><default><0>
+gpio_pin_18 = port:PC03<1><default><default><0>
+gpio_pin_19 = port:PA21<1><default><default><0>
+gpio_pin_20 = port:PA19<1><default><default><0>
+gpio_pin_21 = port:PA18<1><default><default><0>
+gpio_pin_22 = port:PA07<1><default><default><0>
+gpio_pin_23 = port:PA08<1><default><default><0>
+gpio_pin_24 = port:PG08<1><default><default><0>
+gpio_pin_25 = port:PA09<1><default><default><0>
+gpio_pin_26 = port:PA10<1><default><default><0>
+gpio_pin_27 = port:PG09<1><default><default><0>
+gpio_pin_28 = port:PA20<1><default><default><0>
+gpio_pin_29 = port:PG06<1><default><default><0>
+gpio_pin_30 = port:PG07<1><default><default><0>
+
+[led_assign]
+normal_led = "gpio_pin_2"
+standby_led = "gpio_pin_1"
+
+[ths_para]
+ths_used = 1
+ths_trip1_count = 5
+ths_trip1_0 = 70
+ths_trip1_1 = 80
+ths_trip1_2 = 90
+ths_trip1_3 = 100
+ths_trip1_4 = 105
+ths_trip1_5 = 0
+ths_trip1_6 = 0
+ths_trip1_7 = 0
+ths_trip1_0_min = 0
+ths_trip1_0_max = 1
+ths_trip1_1_min = 1
+ths_trip1_1_max = 2
+ths_trip1_2_min = 2
+ths_trip1_2_max = 3
+ths_trip1_3_min = 3
+ths_trip1_3_max = 4
+ths_trip1_4_min = 4
+ths_trip1_4_max = 4
+ths_trip1_5_min = 0
+ths_trip1_5_max = 0
+ths_trip1_6_min = 0
+ths_trip1_6_max = 0
+ths_trip2_count = 1
+ths_trip2_0 = 105
+
+[cooler_table]
+cooler_count = 5
+cooler0 = "1200000 4 4294967295 0"
+cooler1 = "1200000 3 4294967295 0"
+cooler2 = "1200000 2 4294967295 0"
+cooler3 = "1200000 1 4294967295 0"
+cooler4 = "504000 1 4294967295 0"
+
+[nand0_para]
+nand_support_2ch = 0
+nand0_used = 0
+nand0_we = port:PC00<2><default><default><default>
+nand0_ale = port:PC01<2><default><default><default>
+nand0_cle = port:PC02<2><default><default><default>
+nand0_ce1 = port:PC03<2><default><default><default>
+nand0_ce0 = port:PC04<2><default><default><default>
+nand0_nre = port:PC05<2><default><default><default>
+nand0_rb0 = port:PC06<2><default><default><default>
+nand0_rb1 = port:PC07<2><default><default><default>
+nand0_d0 = port:PC08<2><default><default><default>
+nand0_d1 = port:PC09<2><default><default><default>
+nand0_d2 = port:PC10<2><default><default><default>
+nand0_d3 = port:PC11<2><default><default><default>
+nand0_d4 = port:PC12<2><default><default><default>
+nand0_d5 = port:PC13<2><default><default><default>
+nand0_d6 = port:PC14<2><default><default><default>
+nand0_d7 = port:PC15<2><default><default><default>
+nand0_ndqs = port:PC16<2><default><default><default>
+
+[boot_disp]
+advert_disp = 0
+auto_hpd = 1
+output_type = 4
+hdmi_channel = 0
+hdmi_mode = 4
+cvbs_channel = 1
+cvbs_mode = 11
+output_full = 1
+hdmi_mode_check = 1
+
+[disp_init]
+disp_init_enable = 1
+disp_mode = 0
+screen0_output_type = 3
+screen0_output_mode = 4
+screen1_output_type = 3
+screen1_output_mode = 4
+fb0_format = 0
+fb0_width = 0
+fb0_height = 0
+fb1_format = 0
+fb1_width = 0
+fb1_height = 0
+
+[hdmi_para]
+hdmi_used = 1
+hdmi_power = "vcc-hdmi-18"
+
+[tv_para]
+tv_used = 1
+tv_dac_used = 1
+tv_dac_src0 = 0
+
+[pwm0_para]
+pwm_used = 0
+pwm_positive = port:PA05<3><0><default><default>
+; If set gamc_phy to use = 2
+
+[gmac0]
+gmac_used = 2
+gmac_power1 =
+
+[csi0]
+vip_used = 1
+vip_mode = 0
+vip_dev_qty = 1
+vip_define_sensor_list = 0
+vip_csi_pck = port:PE00<2><default><default><default>
+vip_csi_mck = port:PE01<2><default><default><default>
+vip_csi_hsync = port:PE02<2><default><default><default>
+vip_csi_vsync = port:PE03<2><default><default><default>
+vip_csi_d0 = port:PE04<2><default><default><default>
+vip_csi_d1 = port:PE05<2><default><default><default>
+vip_csi_d2 = port:PE06<2><default><default><default>
+vip_csi_d3 = port:PE07<2><default><default><default>
+vip_csi_d4 = port:PE08<2><default><default><default>
+vip_csi_d5 = port:PE09<2><default><default><default>
+vip_csi_d6 = port:PE10<2><default><default><default>
+vip_csi_d7 = port:PE11<2><default><default><default>
+vip_csi_sck = port:PE12<2><default><default><default>
+vip_csi_sda = port:PE13<2><default><default><default>
+vip_dev0_mname = "gc2035"
+vip_dev0_pos = "front"
+vip_dev0_lane = 1
+vip_dev0_twi_id = 2
+vip_dev0_twi_addr = 120
+vip_dev0_isp_used = 0
+vip_dev0_fmt = 0
+vip_dev0_stby_mode = 0
+vip_dev0_vflip = 1
+vip_dev0_hflip = 1
+vip_dev0_iovdd = ""
+vip_dev0_iovdd_vol = 2800000
+vip_dev0_avdd = ""
+vip_dev0_avdd_vol = 2800000
+vip_dev0_dvdd = ""
+vip_dev0_dvdd_vol = 1800000
+vip_dev0_afvdd = ""
+vip_dev0_afvdd_vol = 2800000
+vip_dev0_power_en = port:PA17<1><default><default><1>
+vip_dev0_reset = port:PE14<1><default><default><1>
+vip_dev0_pwdn = port:PE15<1><default><default><0>
+vip_dev0_flash_en =
+vip_dev0_flash_mode =
+vip_dev0_af_pwdn =
+vip_dev0_act_used = 0
+vip_dev0_act_name = "ad5820_act"
+vip_dev0_act_slave = 24
+vip_dev1_mname = ""
+vip_dev1_pos = "rear"
+vip_dev1_lane = 1
+vip_dev1_twi_id = 0
+vip_dev1_twi_addr =
+vip_dev1_isp_used = 0
+vip_dev1_fmt = 1
+vip_dev1_stby_mode = 0
+vip_dev1_vflip = 0
+vip_dev1_hflip = 0
+vip_dev1_iovdd = ""
+vip_dev1_iovdd_vol = 2800000
+vip_dev1_avdd = ""
+vip_dev1_avdd_vol = 2800000
+vip_dev1_dvdd = ""
+vip_dev1_dvdd_vol = 1500000
+vip_dev1_afvdd = ""
+vip_dev1_afvdd_vol = 2800000
+vip_dev1_power_en =
+vip_dev1_reset =
+vip_dev1_pwdn =
+vip_dev1_flash_en =
+vip_dev1_flash_mode =
+vip_dev1_af_pwdn =
+
+[tvout_para]
+tvout_used =
+tvout_channel_num =
+tv_en =
+
+[tvin_para]
+tvin_used =
+tvin_channel_num =
+
+[di_para]
+di_used = 1
+
+[mmc0_para]
+sdc_used = 1
+sdc_detmode = 1
+sdc_buswidth = 4
+sdc_clk = port:PF02<2><1><2><default>
+sdc_cmd = port:PF03<2><1><2><default>
+sdc_d0 = port:PF01<2><1><2><default>
+sdc_d1 = port:PF00<2><1><2><default>
+sdc_d2 = port:PF05<2><1><2><default>
+sdc_d3 = port:PF04<2><1><2><default>
+sdc_det = port:PF06<0><1><2><default>
+sdc_use_wp = 0
+sdc_wp =
+sdc_isio = 0
+sdc_regulator = "none"
+sdc_power_supply = "none"
+
+[mmc1_para]
+sdc_used = 1
+sdc_detmode = 4
+sdc_buswidth = 4
+sdc_clk = port:PG00<2><1><3><default>
+sdc_cmd = port:PG01<2><1><3><default>
+sdc_d0 = port:PG02<2><1><3><default>
+sdc_d1 = port:PG03<2><1><3><default>
+sdc_d2 = port:PG04<2><1><3><default>
+sdc_d3 = port:PG05<2><1><3><default>
+sdc_det =
+sdc_use_wp = 0
+sdc_wp =
+sdc_isio = 1
+sdc_regulator = "none"
+sdc_power_supply = "none"
+sdc_2xmode = 1
+sdc_ddrmode = 1
+
+[mmc2_para]
+sdc_used = 0
+sdc_detmode = 3
+sdc_buswidth = 8
+sdc_clk = port:PC05<3><1><2><default>
+sdc_cmd = port:PC06<3><1><2><default>
+sdc_d0 = port:PC08<3><1><2><default>
+sdc_d1 = port:PC09<3><1><2><default>
+sdc_d2 = port:PC10<3><1><2><default>
+sdc_d3 = port:PC11<3><1><2><default>
+sdc_d4 = port:PC12<3><1><2><default>
+sdc_d5 = port:PC13<3><1><2><default>
+sdc_d6 = port:PC14<3><1><2><default>
+sdc_d7 = port:PC15<3><1><2><default>
+emmc_rst = port:PC16<3><1><2><default>
+sdc_det =
+sdc_use_wp = 0
+sdc_wp =
+sdc_isio = 0
+sdc_regulator = "none"
+sdc_power_supply = "none"
+sdc_2xmode = 1
+sdc_ddrmode = 1
+
+[smc_para]
+smc_used =
+smc_rst = port:PA09<2><default><default><default>
+smc_vppen = port:PA20<3><default><default><default>
+smc_vppp = port:PA21<3><default><default><default>
+smc_det = port:PA10<2><default><default><default>
+smc_vccen = port:PA06<2><default><default><default>
+smc_sck = port:PA07<2><default><default><default>
+smc_sda = port:PA08<2><default><default><default>
+
+[usbc0]
+usb_used = 1
+usb_port_type = 2
+usb_detect_type = 1
+usb_id_gpio = port:PG12<0><1><default><default>
+usb_det_vbus_gpio = port:PG12<0><1><default><default>
+usb_drv_vbus_gpio = port:PL02<1><0><default><0>
+usb_host_init_state = 1
+usb_restrict_gpio =
+usb_restric_flag = 0
+usb_restric_voltage = 3550000
+usb_restric_capacity = 5
+usb_regulator_io = "nocare"
+usb_regulator_vol = 0
+usb_not_suspend = 0
+
+[usbc1]
+usb_used = 1
+usb_drv_vbus_gpio =
+usb_restrict_gpio =
+usb_host_init_state = 1
+usb_restric_flag = 0
+usb_regulator_io = "nocare"
+usb_regulator_vol = 0
+usb_not_suspend = 0
+
+[usbc2]
+usb_used = 1
+usb_drv_vbus_gpio =
+usb_restrict_gpio =
+usb_host_init_state = 1
+usb_restric_flag = 0
+usb_regulator_io = "nocare"
+usb_regulator_vol = 0
+usb_not_suspend = 0
+
+[usbc3]
+usb_used = 1
+usb_drv_vbus_gpio =
+usb_restrict_gpio =
+usb_host_init_state = 1
+usb_restric_flag = 0
+usb_regulator_io = "nocare"
+usb_regulator_vol = 0
+usb_not_suspend = 0
+
+[usb_feature]
+vendor_id = 6353
+mass_storage_id = 1
+adb_id = 2
+manufacturer_name = "USB Developer"
+product_name = "Android"
+serial_number = "20080411"
+
+[msc_feature]
+vendor_name = "USB 2.0"
+product_name = "USB Flash Driver"
+release = 100
+luns = 3
+
+[serial_feature]
+serial_unique = 0
+
+[module_para]
+module_num = 7
+module_power0 = "vcc-wifi-33"
+module_power0_vol = 0
+module_power1 =
+module_power1_vol =
+module_power2 =
+module_power2_vol =
+module_power3 =
+module_power3_vol =
+chip_en =
+lpo_use_apclk =
+
+[wifi_para]
+wifi_used = 0
+wifi_sdc_id = 1
+wifi_usbc_id = 5
+wifi_usbc_type = 1
+wl_reg_on = port:PL07<1><default><default><0>
+wl_host_wake = port:PG10<0><default><default><0>
+wl_host_wake_invert = 0
+
+[bt_para]
+bt_used = 0
+bt_uart_id = 1
+bt_rst_n =
+bt_wake =
+bt_host_wake =
+bt_host_wake_invert = 0
+
+[pcm0]
+daudio_used = 0
+daudio_master = 4
+daudio_select = 1
+audio_format = 1
+signal_inversion = 1
+mclk_fs = 128
+sample_resolution = 16
+slot_width_select = 32
+pcm_lrck_period = 32
+pcm_lrckr_period = 1
+msb_lsb_first = 0
+sign_extend = 0
+slot_index = 0
+slot_width = 32
+frame_width = 0
+tx_data_mode = 0
+rx_data_mode = 0
+i2s_mclk = port:PA18<2><1><default><default>
+i2s_bclk = port:PA19<2><1><default><default>
+i2s_dout0 = port:PA20<2><1><default><default>
+i2s_din = port:PA21<2><1><default><default>
+
+[pcm1]
+daudio_used = 0
+daudio_master = 4
+daudio_select = 1
+audio_format = 1
+signal_inversion = 1
+mclk_fs = 128
+sample_resolution = 16
+slot_width_select = 32
+pcm_lrck_period = 32
+pcm_lrckr_period = 1
+msb_lsb_first = 0
+sign_extend = 0
+slot_index = 0
+slot_width = 32
+frame_width = 0
+tx_data_mode = 0
+rx_data_mode = 0
+i2s_mclk = port:PG10<2><1><default><default>
+i2s_bclk = port:PG11<2><1><default><default>
+i2s_dout0 = port:PG12<2><1><default><default>
+i2s_din = port:PG13<2><1><default><default>
+
+[audio0]
+audio_used = 1
+lineout_vol = 31
+cap_vol = 5
+audio_hp_ldo = "none"
+adcagc_used = 0
+adcdrc_used = 0
+dacdrc_used = 0
+adchpf_used = 0
+dachpf_used = 0
+audio_pa_ctrl = port:PA16<1><default><default><0>
+
+[spdif0]
+spdif_used = 0
+spdif_dout = port:PA17<2><1><default><default>
+
+[audiohub]
+hub_used = 0
+codec_used = 1
+spdif_used = 1
+hdmi_used = 1
+
+[s_cir0]
+ir_used = 1
+ir_rx = port:PL11<2><1><default><default>
+ir_power_key_code0 = 87
+ir_addr_code0 = 40704
+ir_power_key_code1 = 26
+ir_addr_code1 = 64260
+ir_power_key_code2 = 20
+ir_addr_code2 = 32640
+ir_power_key_code3 = 21
+ir_addr_code3 = 32640
+ir_power_key_code4 = 11
+ir_addr_code4 = 63240
+ir_power_key_code5 = 3
+ir_addr_code5 = 239
+ir_power_key_code6 = 159
+ir_addr_code6 = 19635
+ir_power_key_code7 = 10
+ir_addr_code7 = 30536
+ir_power_key_code8 = 69
+ir_addr_code8 = 48386
+ir_power_key_code9 = 77
+ir_addr_code9 = 56865
+ir_power_key_code10 = 24
+ir_addr_code10 = 65025
+ir_power_key_code11 = 87
+ir_addr_code11 = 65280
+ir_power_key_code12 = 77
+ir_addr_code12 = 65344
+
+[cir]
+ir_used = 1
+ir_tx = port:PH07<2><default><default><default>
+
+[dvfs_table]
+pmuic_type = 2
+pmu_gpio0 = port:PL06<1><1><2><1>
+pmu_level0 = 11300
+pmu_level1 = 1100
+#max_freq = 1200000000
+max_freq = 1536000000
+min_freq = 480000000
+LV_count = 8
+#LV1_freq = 1200000000
+LV1_freq = 1536000000
+#LV1_volt = 1300
+LV1_volt = 1500
+#LV2_freq = 1008000000
+LV2_freq = 1200000000
+#LV2_volt = 1200
+LV2_volt = 1300
+LV3_freq = 0
+#LV3_freq = 1008000000
+LV3_volt = 1100
+#LV3_volt = 1200
+LV4_freq = 0
+LV4_volt = 1100
+LV5_freq = 0
+LV5_volt = 1100
+LV6_freq = 0
+LV6_volt = 1100
+LV7_freq = 0
+LV7_volt = 1100
+LV8_freq = 0
+LV8_volt = 1100
+
+[gpu_dvfs_table]
+G_LV_count = 3
+G_LV0_freq = 312000000
+G_LV0_volt = 1200000
+G_LV1_freq = 384000000
+G_LV1_volt = 1200000
+G_LV2_freq = 456000000
+G_LV2_volt = 1200000
+
+[Vdevice]
+Vdevice_used = 0
+Vdevice_0 = port:PH10<5><1><2><default>
+Vdevice_1 = port:PH11<5><1><2><default>
+
+[s_uart0]
+s_uart_used = 0
+s_uart_tx = port:PL02<2><default><default><default>
+s_uart_rx = port:PL03<2><default><default><default>
+
+[s_rsb0]
+s_rsb_used = 1
+s_rsb_sck = port:PL00<2><1><2><default>
+s_rsb_sda = port:PL01<2><1><2><default>
+
+[s_jtag0]
+s_jtag_used = 0
+s_jtag_tms = port:PL04<2><1><2><default>
+s_jtag_tck = port:PL05<2><1><2><default>
+s_jtag_tdo = port:PL06<2><1><2><default>
+s_jtag_tdi = port:PL07<2><1><2><default>
+
+[s_powchk]
+s_powchk_used = -2147483648
+s_power_reg = 0
+s_system_power = 50
+
+[sim0]
+scr_used = 0
+scr_vccen = port:PA06<2><default><default><default>
+scr_slk = port:PA07<2><default><default><default>
+scr_sda = port:PA08<2><default><default><default>
+scr_rst = port:PA09<2><default><default><default>
+scr_det = port:PA10<2><default><default><default>
+
+[ts0]
+tsc_used = 0
+tsc_clk = port:PE00<3><default><default><default>
+tsc_err = port:PE01<3><default><default><default>
+tsc_sync = port:PE02<3><default><default><default>
+tsc_dvld = port:PE03<3><default><default><default>
+tsc_d0 = port:PE04<3><default><default><default>
+tsc_d1 = port:PE05<3><default><default><default>
+tsc_d2 = port:PE06<3><default><default><default>
+tsc_d3 = port:PE07<3><default><default><default>
+tsc_d4 = port:PE08<3><default><default><default>
+tsc_d5 = port:PE09<3><default><default><default>
+tsc_d6 = port:PE10<3><default><default><default>
+tsc_d7 = port:PE11<3><default><default><default>
+
+[gpio_power_key]
+key_used = 1
+key_io = port:PL03<6><default><default><0>
+
+[key_para]
+key_used = 0
+key_cnt = 5
+key1_vol = 222
+key2_vol = 444
+key3_vol = 666
+key4_vol = 857
+key5_vol = 2000
+
+[d7s_para]
+d7s_used = 0
+din_gpio = port:PD00<1><default><default><1>
+clk_gpio = port:PD01<1><default><default><1>
+stb_gpio = port:PD02<1><default><default><1>
+
--
2.4.10

[Siarhei Siamashka]

This patch makes both red and green LEDs available in /sys/class/leds
instead of probably having them reserved for some special purposes
(such as a standby mode indicator?). Being able to control the state
of LEDs from applications and scripts is quite useful.

Signed-off-by: Siarhei Siamashka <siarhei....@gmail.com>
---

sys_config/h3/xunlong_orange_pi_pc.fex | 17 ++++++++++++-----
1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/sys_config/h3/xunlong_orange_pi_pc.fex b/sys_config/h3/xunlong_orange_pi_pc.fex
index 93e8c4c..56a9b60 100644
--- a/sys_config/h3/xunlong_orange_pi_pc.fex
+++ b/sys_config/h3/xunlong_orange_pi_pc.fex
@@ -219,8 +219,8 @@ mode = 0
[gpio_para]
gpio_used = 1
gpio_num = 30
-gpio_pin_1 = port:PL10<1><default><default><1>
-gpio_pin_2 = port:PA15<1><default><default><0>
+; gpio_pin_1 = port:PL10<1><default><default><1>
+; gpio_pin_2 = port:PA15<1><default><default><0>

gpio_pin_3 = port:PA12<1><default><default><0>

gpio_pin_4 = port:PA11<1><default><default><0>

gpio_pin_5 = port:PA06<1><default><default><0>

@@ -250,9 +250,16 @@ gpio_pin_28 = port:PA20<1><default><default><0>

gpio_pin_29 = port:PG06<1><default><default><0>

gpio_pin_30 = port:PG07<1><default><default><0>

-[led_assign]
-normal_led = "gpio_pin_2"
-standby_led = "gpio_pin_1"
+;[led_assign]
+;normal_led = "gpio_pin_2"
+;standby_led = "gpio_pin_1"
+
+[leds_para]
+leds_used = 1
+green_led = port:PL10<1><default><default><0>
+green_led_active_low = 0
+red_led = port:PA15<1><default><default><0>
+red_led_active_low = 0

[ths_para]
ths_used = 1
--
2.4.10

[Siarhei Siamashka]

The current FEX file does not allow the CPU frequencies higher
than 1.2GHz and also sets the VDD_CPUX voltage to 1.3V (the
cooling states table overrides the questionable 1536MHz @1.5V
cpufreq operating point).

The comments in FEX files from H3 SDK sources are describing
the cpufreq operating points and looks like the information
provided by Allwinner (the same comments are also present
in the Draco H3 SDK). So use these operating points instead.
Also the H3 datasheet specifies 1.5V as the absolute maximum
for the VDD_CPUX voltage and 1.4V as the recommended maximum.
The datasheet says that "Absolute Maximum Ratings are those
values beyond which damage to the device may occur" and
"Functional operation of the device *at these* or any other
conditions beyond those indicated in the operational sections
of this standard may damage to the device". Basically, the
recommended voltage limit is 1.4V while the range between
1.4V and 1.5V is a buffer zone for extra safety. For this
reason, the 1536MHz operating point is removed. Tests with
libjpeg-turbo decoding show that there is at least some
safety headroom (no corruption detected until these voltages
are reduced by more than 0.07V).

Regarding the cooling states, the old FEX file was instructing
the kernel to disable CPU cores as the temperature increases
while keeping the CPU clock speed limit at all the same 1.2GHz.
Probably the intention was to ensure that the single-threaded
performance remains good. But the problem with this approach is
that once a CPU core is disabled, it does not come back anymore
when using the Allwinner's 3.4 SDK kernel. An alternative
solution is to keep all the CPU cores operational as long as
possible, but reduce the CPU clock speed limit at higher
temperatures. Such adjustment is also done by this patch.

Signed-off-by: Siarhei Siamashka <siarhei....@gmail.com>
---

sys_config/h3/xunlong_orange_pi_pc.fex | 86 ++++++++++++++++++++--------------
1 file changed, 52 insertions(+), 34 deletions(-)

diff --git a/sys_config/h3/xunlong_orange_pi_pc.fex b/sys_config/h3/xunlong_orange_pi_pc.fex
index 56a9b60..88ee928 100644
--- a/sys_config/h3/xunlong_orange_pi_pc.fex
+++ b/sys_config/h3/xunlong_orange_pi_pc.fex
@@ -263,13 +263,13 @@ red_led_active_low = 0

[ths_para]
ths_used = 1
-ths_trip1_count = 5
+ths_trip1_count = 6
ths_trip1_0 = 70
ths_trip1_1 = 80
-ths_trip1_2 = 90
-ths_trip1_3 = 100
-ths_trip1_4 = 105
-ths_trip1_5 = 0
+ths_trip1_2 = 85
+ths_trip1_3 = 90
+ths_trip1_4 = 95
+ths_trip1_5 = 100
ths_trip1_6 = 0
ths_trip1_7 = 0
ths_trip1_0_min = 0
@@ -281,21 +281,22 @@ ths_trip1_2_max = 3
ths_trip1_3_min = 3
ths_trip1_3_max = 4
ths_trip1_4_min = 4
-ths_trip1_4_max = 4
-ths_trip1_5_min = 0
-ths_trip1_5_max = 0
+ths_trip1_4_max = 5
+ths_trip1_5_min = 5
+ths_trip1_5_max = 5
ths_trip1_6_min = 0
ths_trip1_6_max = 0
ths_trip2_count = 1
ths_trip2_0 = 105

[cooler_table]
-cooler_count = 5
-cooler0 = "1200000 4 4294967295 0"
-cooler1 = "1200000 3 4294967295 0"
-cooler2 = "1200000 2 4294967295 0"
-cooler3 = "1200000 1 4294967295 0"
-cooler4 = "504000 1 4294967295 0"
+cooler_count = 6
+cooler0 = "1296000 4 4294967295 0"
+cooler1 = "1200000 4 4294967295 0"
+cooler2 = "1008000 4 4294967295 0"
+cooler3 = "816000 4 4294967295 0"
+cooler4 = "648000 4 4294967295 0"
+cooler5 = "480000 1 4294967295 0"

[nand0_para]
nand_support_2ch = 0
@@ -709,37 +710,54 @@ ir_addr_code12 = 65344
ir_used = 1

ir_tx = port:PH07<2><default><default><default>

+;----------------------------------------------------------------------------------
+; dvfs voltage-frequency table configuration
+;
+; pmuic_type:0:none, 1:gpio, 2:i2c
+; pmu_gpio0: gpio config.
+; pmu_levelx: 0~9999: voltage(mV), 10000~90000:gpio0 state. voltage form high to low.
+;
+; extremity_freq(Hz): cpu extremity frequency when run benckmark or demo apk
+; 1536MHz@1500mV with radiator, 1296MHz@1340mV without radiator
+; max_freq: cpu maximum frequency, based on Hz, can not be more than 1200MHz
+; min_freq: cpu minimum frequency, based on Hz, can not be less than 60MHz
+;
+; LV_count: count of LV_freq/LV_volt, must be < 16
+;
+; LV1: core vdd is 1.50v if cpu frequency is (1296Mhz, 1536Mhz]
+; LV2: core vdd is 1.34v if cpu frequency is (1200Mhz, 1296Mhz]
+; LV3: core vdd is 1.32v if cpu frequency is (1008Mhz, 1200Mhz]
+; LV4: core vdd is 1.20v if cpu frequency is (816Mhz, 1008Mhz]
+; LV5: core vdd is 1.10v if cpu frequency is (648Mhz, 816Mhz]
+; LV6: core vdd is 1.04v if cpu frequency is (0Mhz, 648Mhz]
+; LV7: core vdd is 1.04v if cpu frequency is (0Mhz, 648Mhz]
+; LV8: core vdd is 1.04v if cpu frequency is (0Mhz, 648Mhz]
+;
+;----------------------------------------------------------------------------------
[dvfs_table]
pmuic_type = 2

pmu_gpio0 = port:PL06<1><1><2><1>

pmu_level0 = 11300
pmu_level1 = 1100
-#max_freq = 1200000000
-max_freq = 1536000000
-min_freq = 480000000
+max_freq = 1296000000
+min_freq = 648000000
LV_count = 8
-#LV1_freq = 1200000000
-LV1_freq = 1536000000
-#LV1_volt = 1300
-LV1_volt = 1500
-#LV2_freq = 1008000000
+LV1_freq = 1296000000
+LV1_volt = 1340
LV2_freq = 1200000000
-#LV2_volt = 1200
-LV2_volt = 1300
-LV3_freq = 0
-#LV3_freq = 1008000000
-LV3_volt = 1100
-#LV3_volt = 1200
-LV4_freq = 0
+LV2_volt = 1320
+LV3_freq = 1008000000
+LV3_volt = 1200
+LV4_freq = 816000000
LV4_volt = 1100
-LV5_freq = 0
-LV5_volt = 1100
+LV5_freq = 648000000
+LV5_volt = 1040
LV6_freq = 0
-LV6_volt = 1100
+LV6_volt = 1040
LV7_freq = 0
-LV7_volt = 1100
+LV7_volt = 1040
LV8_freq = 0
-LV8_volt = 1100
+LV8_volt = 1040

[gpu_dvfs_table]
G_LV_count = 3
--
2.4.10

[Thomas Kaiser]

Siarhei Siamashka:

Extracted from the Lubuntu_1404_For_OrangePiPC_v0_8_0_.img.xz image:
http://www.orangepi.org/downloadresources/orangepipc/oragepipc_4a0e8d960f7f0a52606dfaba58.html

Not necessarily the best one

This is the worst one since it's the origin of all thermal problems with Orange Pis and the result of product marketing: Advertising the H3 to be able to run at "up to 1.6Ghz". All Steven did was to increase clockspeeds and to adjust the Vcore voltage of the two available operting points in the dvs table he took from Draco by 200mV (to be able to reach the extremity_freq as scaling_max_freq).

And the result is that everyone using OS images for H3 based Orange Pi models has to suffer from heat/stability problems. When you replace this moronic dvfs table with something sane (a few more operating points and not only 2 already exceeding the recommended maximum values), you won't even need a heatsink:

http://linux-sunxi.org/User_talk:Tkaiser#Lessons_to_learn_from_Xunlong

With Xunlong's dvfs settings switching between 1.2 Ghz and 1.56 GHz *while being idle* the SoC's temperature increases by 12°C.

I don't know what I'm doing wrong but I can fire up cpuburn-a7 running on all 4 CPU cores at 1.2Ghz on my Orange Pi PC without thermal throttling, without CPU cores being dropped and also without heatsink/fan attached. Can please anyone explain to me what's wrong with my Orange Pi?

[Siarhei Siamashka]

On Wed, 9 Dec 2015 00:40:18 -0800 (PST)
Thomas Kaiser <thomas...@phg-online.de> wrote:

> Siarhei Siamashka:
>
> > Extracted from the Lubuntu_1404_For_OrangePiPC_v0_8_0_.img.xz image:
> >
> > http://www.orangepi.org/downloadresources/orangepipc/oragepipc_4a0e8d960f7f0a52606dfaba58.html
> >
> > Not necessarily the best one
> >
>
> This is the worst one since it's the origin of all thermal problems with
> Orange Pis

It is not the worst one. This particular FEX file only allows clock
speeds up to 1.2 GHz because the CPU clock frequency must satisfy
*both* cpufreq and also cooling state requirements at once. Yes, the
cpufreq table lists 1.5GHz as the maximum clock frequency. But at the
same time, the highest cooling state only allows 4 cores running at
1.2GHz in this FEX. I had some explanations about this in my third
patch "h3: Update cpufreq and cooling state tables on Orange Pi PC".

It's likely that the credit for "unlocking" the 1.5 GHz clock speed
actually belongs to third-party modders.

> and the result of product marketing: Advertising the H3 to be
> able to run at "up to 1.6Ghz".

Right now http://www.orangepi.org/orangepipc/ page does not say
anything about the CPU clock frequency. I guess, there was a time
period when nobody had any idea about what would be the CPU clock
speed limit because Allwinner does not really provide this information
in the H3 manual.

Regarding the product marketing. The primary competitors are probably
the Raspberry Pi 2 running at 900 MHz and the ODROID C1 running at 1.5
GHz. So 1.6 GHz would definitely look attractive in the marketing
materials if this was true.

It looks like H3 can be clocked at least up to 1.3 GHz with the
CPU core voltage not exceeding the 1.4V limit specified in the H3
manual. But running all 4 cores at this clock speeds for prolonged
periods of time may be difficult because of thermal throttling.
On the other hand, a single-threaded workload at 1.3 GHz is
probably perfectly fine. It's roughly the same as
https://en.wikipedia.org/wiki/Intel_Turbo_Boost
Intel is playing safe and provides two clock frequencies in the
marketing materials (the "nominal" clock frequency and the "boosted"
one). Maybe that's the way to go?

A heatsink is just an optional performance feature, which may allow
your system to run faster and keep the cores always running at full
speed. It is not necessary for reliable operation, but the peak
performance may degrade without it.

> All Steven did was to increase clockspeeds
> and to adjust the Vcore voltage of the two available operting points in the
> dvs table he took from Draco by 200mV (to be able to reach the
> extremity_freq as scaling_max_freq).
>
> And the result is that everyone using OS images for H3 based Orange Pi
> models has to suffer from heat/stability problems. When you replace this
> moronic dvfs table with something sane (a few more operating points and not
> only 2 already exceeding the recommended maximum values), you won't even
> need a heatsink:
>
> http://linux-sunxi.org/User_talk:Tkaiser#Lessons_to_learn_from_Xunlong
>
> With Xunlong's dvfs settings switching between 1.2 Ghz and 1.56 GHz *while
> being idle* the SoC's temperature increases by 12°C.
>
> I don't know what I'm doing wrong but I can fire up cpuburn-a7 running on
> all 4 CPU cores at 1.2Ghz on my Orange Pi PC without thermal throttling,
> without CPU cores being dropped and also without heatsink/fan attached. Can
> please anyone explain to me what's wrong with my Orange Pi?

This is called undervolting. With overclocking one is pushing the
absolute performance limits. And with undervolting one pushing the
performance/watt limits.

But there is some variation in voltage tolerances between different
samples, so sufficient safety headroom must be provided in the
general purpose configuration to make it suitable for everyone.
Even if you can reduce the voltage to the very minimum on your
board, this does not automatically mean that any other guy with
a different Orange Pi PC board would be also able to use the same
voltage safely.

As there were no real objections, I have just pushed the Orange Pi PC
fex file to the sunxi-boards repository. This makes it the first FEX
file for the H3 SoC :-)

--
Best regards,
Siarhei Siamashka

[Thomas Kaiser]

Siarhei Siamashka wrote:

It's likely that the credit for "unlocking" the 1.5 GHz clock speed

actually belongs to third-party modders.

Thanks for clarifying this (and all the additional informations). I'll 

try to correct this where I spread wrong "informations"/assumptions 

asapissimo.

As there were no real objections, I have just pushed the Orange Pi PC

fex file to the sunxi-boards repository. This makes it the first FEX

file for the H3 SoC :-)

Great. Only one single question (I've overlooked before). Why

    boot_clock = 1200

(especially since you wrote about SY8106A's default 1.2V voltage being 

safe for operation at 1008 MHz)

Thx,

Thomas

[Siarhei Siamashka]

Thanks, that was a good question.

The "boot_clock" parameter is not used by the linux kernel. It's the
Allwinner's bootloader thing. You can grep the H3 SDK sources to check
this.

As for the other things left to do, the DRAM clock speed needs to
be adjusted in the FEX file after we find a reasonable default DRAM
clock speed.

The reason is that on every cooling state change in the 3.4 kernel
(after crossing any temperature threshold, for example 70C), there
is a hook into the DRAM reclocking code. This code simply sets 480MHz
DRAM clock speed if the temperature is 100C or higher. And if the
temperature is below 100C, then the dram clock value from FEX is
used.