Ender3 Pro Dyze Pro Big Problem
233 views
Skip to first unread message
![3DFans [Ben]'s profile photo](http://lh3.googleusercontent.com/a-/ALV-UjViPk704myWq2qhQmiVYoauApCbhXhEvSnZl2LLTh6Y0mElYdGf=s40-c)
3DFans [Ben]
Dec 4, 2020, 7:28:25 AM12/4/20
to DYZE DESIGN
Greet you,
I was just about to install my Dyze Pro on the new Ender3 Pro with the SKR Mini E3 V2. So far so good, but from the front I get a nozzle temperature of 291 ° C and I don't know where the error is. All cables checked, but I don't see any faults there. The thermistor shouldn't be faulty either.
Do you have any idea why that could be?
Philippe Carrier
Dec 4, 2020, 7:35:09 AM12/4/20
to DYZE DESIGN, benva...@gmail.com
Looking at the high temperature thermistor table, I believe you are trying to use a PT100 on a 500°C thermistor configuration.
To run a PT100, you'll need an amplification board.
3DFans [Ben]
Dec 4, 2020, 8:17:11 AM12/4/20
to DYZE DESIGN, benva...@gmail.com
Hey, I have the 500 ° C version and the sensor is 66.
3DFans [Ben]
Dec 4, 2020, 8:32:55 AM12/4/20
to DYZE DESIGN
Have a look, but which PT100 should I test? If I take the -5, it shows me several errors.
Philippe Carrier
Dec 4, 2020, 10:06:22 AM12/4/20
to DYZE DESIGN, benva...@gmail.com
Interesting. Please try measuring the resistance between the leads. If it's a PT100, you should measure around 105Ω. If it's a 500°C thermistor, you should measure more than 4MΩ.
The PT100 in Marlin all requires an amplifier circuit to work.
3DFans [Ben]
Dec 4, 2020, 10:13:30 AM12/4/20
to DYZE DESIGN, benva...@gmail.com
Hey, I don't have the possibility to measure, but it's the one with the black hose and thus 500 ° C. If I change the thermistor to marlin to 3, the display shows only 197 ° C. So the mistake must be somewhere, but what else can you do? It would be a shame if I couldn't use the set and put it in the closet. : /
Philippe Carrier
Dec 4, 2020, 10:18:51 AM12/4/20
to DYZE DESIGN, benva...@gmail.com
Very strange. Have you tried unplugging the sensor using the #66 table? What value do you get?
Have you tried a different temperature input? You can try a different one than T0 from the firmware+board?
3DFans [Ben]
Dec 4, 2020, 10:21:57 AM12/4/20
to DYZE DESIGN, benva...@gmail.com
Very strange, because I just turned off the sensor and it still shows a value of 160 ° C. Unfortunately, the E3 Mini V2 only has one input TH0.
Philippe Carrier
Dec 7, 2020, 6:48:31 AM12/7/20
to DYZE DESIGN, benva...@gmail.com
Indeed, I'm not sure where the problem comes from...
Do you have a pack of resistances where you could fit them inside the connector? This way, we could try a few values and see the firmware interpretation of their temperature.
If the firmware is telling the right values, then the sensor is defect and we'll send you a new one.
3DFans [Ben]
Dec 7, 2020, 6:51:18 AM12/7/20
to DYZE DESIGN, benva...@gmail.com
Hey, I also ordered a new board, the new SKR E3 Turbo, so that I can rule out a hardware defect, but there is also the same problem. I then connected a "cheap" thermistor and it worked, so it is on the Dyze thermistor.
3DFans [Ben]
Dec 10, 2020, 10:26:42 AM12/10/20
to DYZE DESIGN, benva...@gmail.com
So, I had ordered a new thermistor in the meantime, but with 300 ° C and that doesn't work either. Because 17 ° C-18 ° C are shown continuously in the display. If I now want to heat up to 50 ° C, "Heating not successful" comes after a few seconds and starts to beep. In Marlin the thermistor 3 was selected and the PID tuning was entered. To be on the safe side, I also used two other heating cartridges, but that didn't work either. But where should the error still lie?
Patrick Emerick
Dec 10, 2020, 11:02:57 AM12/10/20
to DYZE DESIGN, benva...@gmail.com
Assuming you have the correct temperature table setup for the thermistor you're using and the input circuit resistance, this sounds like a potential problem with your Marlin pin configuration.
3DFans [Ben]
Dec 10, 2020, 12:19:43 PM12/10/20
to DYZE DESIGN, benva...@gmail.com
Hey, now I've got a grip on it, but the temperature still doesn't quite work. If I do a PID tuning and set a target of 50 ° C as an example, it goes up to 80 ° C and that's not normal?
/** * Marlin 3D Printer Firmware * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see <https://www.gnu.org/licenses/>. * */#pragma once
#include "../core/boards.h"
/** * Include pins definitions * * Pins numbering schemes: * * - Digital I/O pin number if used by READ/WRITE macros. (e.g., X_STEP_DIR) * The FastIO headers map digital pins to their ports and functions. * * - Analog Input number if used by analogRead or DAC. (e.g., TEMP_n_PIN) * These numbers are the same in any pin mapping. */
#define MAX_EXTRUDERS 8
#if MB(RAMPS_13_EFB, RAMPS_14_EFB, RAMPS_PLUS_EFB, RAMPS_14_RE_ARM_EFB, RAMPS_SMART_EFB, RAMPS_DUO_EFB, RAMPS4DUE_EFB) #define IS_RAMPS_EFB#elif MB(RAMPS_13_EEB, RAMPS_14_EEB, RAMPS_PLUS_EEB, RAMPS_14_RE_ARM_EEB, RAMPS_SMART_EEB, RAMPS_DUO_EEB, RAMPS4DUE_EEB) #define IS_RAMPS_EEB#elif MB(RAMPS_13_EFF, RAMPS_14_EFF, RAMPS_PLUS_EFF, RAMPS_14_RE_ARM_EFF, RAMPS_SMART_EFF, RAMPS_DUO_EFF, RAMPS4DUE_EFF) #define IS_RAMPS_EFF#elif MB(RAMPS_13_EEF, RAMPS_14_EEF, RAMPS_PLUS_EEF, RAMPS_14_RE_ARM_EEF, RAMPS_SMART_EEF, RAMPS_DUO_EEF, RAMPS4DUE_EEF) #define IS_RAMPS_EEF#elif MB(RAMPS_13_SF, RAMPS_14_SF, RAMPS_PLUS_SF, RAMPS_14_RE_ARM_SF, RAMPS_SMART_SF, RAMPS_DUO_SF, RAMPS4DUE_SF) #define IS_RAMPS_SF#endif
#define HAS_FREE_AUX2_PINS !(BOTH(ULTRA_LCD, NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, MINIPANEL, REPRAPWORLD_KEYPAD))
// Test the target within the included pins file#ifdef __MARLIN_DEPS__ #define NOT_TARGET(V...) 0#else #define NOT_TARGET(V...) NONE(V)#endif
//// RAMPS 1.3 / 1.4 - ATmega1280, ATmega2560//
#if MB(RAMPS_OLD) #include "ramps/pins_RAMPS_OLD.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_13_EFB) #include "ramps/pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_13_EEB) #include "ramps/pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_13_EFF) #include "ramps/pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_13_EEF) #include "ramps/pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_13_SF) #include "ramps/pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_14_EFB) #include "ramps/pins_RAMPS.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_14_EEB) #include "ramps/pins_RAMPS.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_14_EFF) #include "ramps/pins_RAMPS.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_14_EEF) #include "ramps/pins_RAMPS.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_14_SF) #include "ramps/pins_RAMPS.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_PLUS_EFB) #include "ramps/pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_PLUS_EEB) #include "ramps/pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_PLUS_EFF) #include "ramps/pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_PLUS_EEF) #include "ramps/pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RAMPS_PLUS_SF) #include "ramps/pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560
//// RAMPS Derivatives - ATmega1280, ATmega2560//
#elif MB(3DRAG) #include "ramps/pins_3DRAG.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(K8200) #include "ramps/pins_K8200.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560 (3DRAG)#elif MB(K8400) #include "ramps/pins_K8400.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560 (3DRAG)#elif MB(K8600) #include "ramps/pins_K8600.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(K8800) #include "ramps/pins_K8800.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560 (3DRAG)#elif MB(BAM_DICE) #include "ramps/pins_RAMPS.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(BAM_DICE_DUE) #include "ramps/pins_BAM_DICE_DUE.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(MKS_BASE) #include "ramps/pins_MKS_BASE_10.h" // ATmega2560 env:mega2560#elif MB(MKS_BASE_14) #include "ramps/pins_MKS_BASE_14.h" // ATmega2560 env:mega2560#elif MB(MKS_BASE_15) #include "ramps/pins_MKS_BASE_15.h" // ATmega2560 env:mega2560#elif MB(MKS_BASE_16) #include "ramps/pins_MKS_BASE_16.h" // ATmega2560 env:mega2560#elif MB(MKS_BASE_HEROIC) #include "ramps/pins_MKS_BASE_HEROIC.h" // ATmega2560 env:mega2560#elif MB(MKS_GEN_13) #include "ramps/pins_MKS_GEN_13.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(MKS_GEN_L) #include "ramps/pins_MKS_GEN_L.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(KFB_2) #include "ramps/pins_BIQU_KFB_2.h" // ATmega2560 env:mega2560#elif MB(ZRIB_V20) #include "ramps/pins_ZRIB_V20.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560 (MKS_GEN_13)#elif MB(FELIX2) #include "ramps/pins_FELIX2.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RIGIDBOARD) #include "ramps/pins_RIGIDBOARD.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(RIGIDBOARD_V2) #include "ramps/pins_RIGIDBOARD_V2.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(SAINSMART_2IN1) #include "ramps/pins_SAINSMART_2IN1.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(ULTIMAKER) #include "ramps/pins_ULTIMAKER.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(ULTIMAKER_OLD) #include "ramps/pins_ULTIMAKER_OLD.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(AZTEEG_X3) #include "ramps/pins_AZTEEG_X3.h" // ATmega2560 env:mega2560#elif MB(AZTEEG_X3_PRO) #include "ramps/pins_AZTEEG_X3_PRO.h" // ATmega2560 env:mega2560#elif MB(ULTIMAIN_2) #include "ramps/pins_ULTIMAIN_2.h" // ATmega2560 env:mega2560ext#elif MB(FORMBOT_RAPTOR) #include "ramps/pins_FORMBOT_RAPTOR.h" // ATmega2560 env:mega2560#elif MB(FORMBOT_RAPTOR2) #include "ramps/pins_FORMBOT_RAPTOR2.h" // ATmega2560 env:mega2560#elif MB(FORMBOT_TREX2PLUS) #include "ramps/pins_FORMBOT_TREX2PLUS.h" // ATmega2560 env:mega2560#elif MB(FORMBOT_TREX3) #include "ramps/pins_FORMBOT_TREX3.h" // ATmega2560 env:mega2560#elif MB(RUMBA) #include "ramps/pins_RUMBA.h" // ATmega2560 env:mega2560#elif MB(RUMBA_RAISE3D) #include "ramps/pins_RUMBA_RAISE3D.h" // ATmega2560 env:mega2560#elif MB(RL200) #include "ramps/pins_RL200.h" // ATmega2560 env:mega2560#elif MB(BQ_ZUM_MEGA_3D) #include "ramps/pins_BQ_ZUM_MEGA_3D.h" // ATmega2560 env:mega2560ext#elif MB(MAKEBOARD_MINI) #include "ramps/pins_MAKEBOARD_MINI.h" // ATmega2560 env:mega2560#elif MB(TRIGORILLA_13) #include "ramps/pins_TRIGORILLA_13.h" // ATmega2560 env:mega2560#elif MB(TRIGORILLA_14) #include "ramps/pins_TRIGORILLA_14.h" // ATmega2560 env:mega2560#elif MB(TRIGORILLA_14_11) #include "ramps/pins_TRIGORILLA_14.h" // ATmega2560 env:mega2560#elif MB(RAMPS_ENDER_4) #include "ramps/pins_RAMPS_ENDER_4.h" // ATmega2560 env:mega2560#elif MB(RAMPS_CREALITY) #include "ramps/pins_RAMPS_CREALITY.h" // ATmega2560 env:mega2560#elif MB(RAMPS_DAGOMA) #include "ramps/pins_RAMPS_DAGOMA.h" // ATmega2560 env:mega2560#elif MB(FYSETC_F6_13) #include "ramps/pins_FYSETC_F6_13.h" // ATmega2560 env:FYSETC_F6_13#elif MB(FYSETC_F6_14) #include "ramps/pins_FYSETC_F6_14.h" // ATmega2560 env:FYSETC_F6_14#elif MB(DUPLICATOR_I3_PLUS) #include "ramps/pins_DUPLICATOR_I3_PLUS.h" // ATmega2560 env:mega2560#elif MB(VORON) #include "ramps/pins_VORON.h" // ATmega2560 env:mega2560#elif MB(TRONXY_V3_1_0) #include "ramps/pins_TRONXY_V3_1_0.h" // ATmega2560 env:mega2560#elif MB(Z_BOLT_X_SERIES) #include "ramps/pins_Z_BOLT_X_SERIES.h" // ATmega2560 env:mega2560#elif MB(TT_OSCAR) #include "ramps/pins_TT_OSCAR.h" // ATmega2560 env:mega2560#elif MB(TANGO) #include "ramps/pins_TANGO.h" // ATmega2560 env:mega2560#elif MB(MKS_GEN_L_V2) #include "ramps/pins_MKS_GEN_L_V2.h" // ATmega2560 env:mega2560#elif MB(COPYMASTER_3D) #include "ramps/pins_COPYMASTER_3D.h" // ATmega2560 env:mega2560#elif MB(ORTUR_4) #include "ramps/pins_ORTUR_4.h" // ATmega2560 env:mega2560#elif MB(TENLOG_D3_HERO) #include "ramps/pins_TENLOG_D3_HERO.h" // ATmega2560 env:mega2560#elif MB(MKS_GEN_L_V21) #include "ramps/pins_MKS_GEN_L_V21.h" // ATmega2560 env:mega2560
//// RAMBo and derivatives//
#elif MB(RAMBO) #include "rambo/pins_RAMBO.h" // ATmega2560 env:rambo#elif MB(MINIRAMBO, MINIRAMBO_10A) #include "rambo/pins_MINIRAMBO.h" // ATmega2560 env:rambo#elif MB(EINSY_RAMBO) #include "rambo/pins_EINSY_RAMBO.h" // ATmega2560 env:rambo#elif MB(EINSY_RETRO) #include "rambo/pins_EINSY_RETRO.h" // ATmega2560 env:rambo#elif MB(SCOOVO_X9H) #include "rambo/pins_SCOOVO_X9H.h" // ATmega2560 env:rambo
//// Other ATmega1280, ATmega2560//
#elif MB(CNCONTROLS_11) #include "mega/pins_CNCONTROLS_11.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(CNCONTROLS_12) #include "mega/pins_CNCONTROLS_12.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(CNCONTROLS_15) #include "mega/pins_CNCONTROLS_15.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(MIGHTYBOARD_REVE) #include "mega/pins_MIGHTYBOARD_REVE.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560ext#elif MB(CHEAPTRONIC) #include "mega/pins_CHEAPTRONIC.h" // ATmega2560 env:mega2560#elif MB(CHEAPTRONIC_V2) #include "mega/pins_CHEAPTRONICv2.h" // ATmega2560 env:mega2560#elif MB(MEGATRONICS) #include "mega/pins_MEGATRONICS.h" // ATmega2560 env:mega2560#elif MB(MEGATRONICS_2) #include "mega/pins_MEGATRONICS_2.h" // ATmega2560 env:mega2560#elif MB(MEGATRONICS_3, MEGATRONICS_31, MEGATRONICS_32) #include "mega/pins_MEGATRONICS_3.h" // ATmega2560 env:mega2560#elif MB(ELEFU_3) #include "mega/pins_ELEFU_3.h" // ATmega2560 env:mega2560#elif MB(LEAPFROG) #include "mega/pins_LEAPFROG.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(MEGACONTROLLER) #include "mega/pins_MEGACONTROLLER.h" // ATmega2560 env:mega2560#elif MB(GT2560_REV_A) #include "mega/pins_GT2560_REV_A.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(GT2560_REV_A_PLUS) #include "mega/pins_GT2560_REV_A_PLUS.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560#elif MB(GT2560_V3) #include "mega/pins_GT2560_V3.h" // ATmega2560 env:mega2560#elif MB(GT2560_V3_MC2) #include "mega/pins_GT2560_V3_MC2.h" // ATmega2560 env:mega2560#elif MB(GT2560_V3_A20) #include "mega/pins_GT2560_V3_A20.h" // ATmega2560 env:mega2560#elif MB(EINSTART_S) #include "mega/pins_EINSTART-S.h" // ATmega1280, ATmega2560 env:mega1280 env:mega2560ext#elif MB(WANHAO_ONEPLUS) #include "mega/pins_WANHAO_ONEPLUS.h" // ATmega2560 env:mega2560#elif MB(OVERLORD) #include "mega/pins_OVERLORD.h" // ATmega2560 env:mega2560#elif MB(HJC2560C_REV2) #include "mega/pins_HJC2560C_REV2.h" // ATmega2560 env:mega2560#elif MB(LEAPFROG_XEED2015) #include "mega/pins_LEAPFROG_XEED2015.h" // ATmega2560 env:mega2560#elif MB(PICA) #include "mega/pins_PICA.h" // ATmega2560 env:mega2560#elif MB(PICA_REVB) #include "mega/pins_PICAOLD.h" // ATmega2560 env:mega2560#elif MB(INTAMSYS40) #include "mega/pins_INTAMSYS40.h" // ATmega2560 env:mega2560
//// ATmega1281, ATmega2561//
#elif MB(MINITRONICS) #include "mega/pins_MINITRONICS.h" // ATmega1281 env:mega1280#elif MB(SILVER_GATE) #include "mega/pins_SILVER_GATE.h" // ATmega2561 env:mega2560
//// Sanguinololu and Derivatives - ATmega644P, ATmega1284P//
#elif MB(SANGUINOLOLU_11) #include "sanguino/pins_SANGUINOLOLU_11.h" // ATmega644P, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(SANGUINOLOLU_12) #include "sanguino/pins_SANGUINOLOLU_12.h" // ATmega644P, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(MELZI) #include "sanguino/pins_MELZI.h" // ATmega644P, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(MELZI_V2) #include "sanguino/pins_MELZI_V2.h" // ATmega644P, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(MELZI_MAKR3D) #include "sanguino/pins_MELZI_MAKR3D.h" // ATmega644P, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(MELZI_CREALITY) #include "sanguino/pins_MELZI_CREALITY.h" // ATmega1284P env:melzi env:melzi_optimized env:melzi_optiboot#elif MB(MELZI_MALYAN) #include "sanguino/pins_MELZI_MALYAN.h" // ATmega644P, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(MELZI_TRONXY) #include "sanguino/pins_MELZI_TRONXY.h" // ATmega644P, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(STB_11) #include "sanguino/pins_STB_11.h" // ATmega644P, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(AZTEEG_X1) #include "sanguino/pins_AZTEEG_X1.h" // ATmega644P, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(ZMIB_V2) #include "sanguino/pins_ZMIB_V2.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p
//// Other ATmega644P, ATmega644, ATmega1284P//
#elif MB(GEN3_MONOLITHIC) #include "sanguino/pins_GEN3_MONOLITHIC.h" // ATmega644P env:sanguino644p#elif MB(GEN3_PLUS) #include "sanguino/pins_GEN3_PLUS.h" // ATmega644P, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(GEN6) #include "sanguino/pins_GEN6.h" // ATmega644P, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(GEN6_DELUXE) #include "sanguino/pins_GEN6_DELUXE.h" // ATmega644P, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(GEN7_CUSTOM) #include "sanguino/pins_GEN7_CUSTOM.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(GEN7_12) #include "sanguino/pins_GEN7_12.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(GEN7_13) #include "sanguino/pins_GEN7_13.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(GEN7_14) #include "sanguino/pins_GEN7_14.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino644p env:sanguino1284p#elif MB(OMCA_A) #include "sanguino/pins_OMCA_A.h" // ATmega644 env:sanguino644p#elif MB(OMCA) #include "sanguino/pins_OMCA.h" // ATmega644P, ATmega644 env:sanguino644p#elif MB(ANET_10) #include "sanguino/pins_ANET_10.h" // ATmega1284P env:sanguino1284p#elif MB(SETHI) #include "sanguino/pins_SETHI.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino644p env:sanguino1284p
//// Teensyduino - AT90USB1286, AT90USB1286P//
#elif MB(TEENSYLU) #include "teensy2/pins_TEENSYLU.h" // AT90USB1286, AT90USB1286P env:at90usb1286_cdc#elif MB(PRINTRBOARD) #include "teensy2/pins_PRINTRBOARD.h" // AT90USB1286 env:at90usb1286_dfu#elif MB(PRINTRBOARD_REVF) #include "teensy2/pins_PRINTRBOARD_REVF.h" // AT90USB1286 env:at90usb1286_dfu#elif MB(BRAINWAVE) #include "teensy2/pins_BRAINWAVE.h" // AT90USB646 env:at90usb1286_cdc#elif MB(BRAINWAVE_PRO) #include "teensy2/pins_BRAINWAVE_PRO.h" // AT90USB1286 env:at90usb1286_cdc#elif MB(SAV_MKI) #include "teensy2/pins_SAV_MKI.h" // AT90USB1286 env:at90usb1286_cdc#elif MB(TEENSY2) #include "teensy2/pins_TEENSY2.h" // AT90USB1286 env:teensy20#elif MB(5DPRINT) #include "teensy2/pins_5DPRINT.h" // AT90USB1286 env:at90usb1286_dfu
//// LPC1768 ARM Cortex M3//
#elif MB(RAMPS_14_RE_ARM_EFB) #include "lpc1768/pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768#elif MB(RAMPS_14_RE_ARM_EEB) #include "lpc1768/pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768#elif MB(RAMPS_14_RE_ARM_EFF) #include "lpc1768/pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768#elif MB(RAMPS_14_RE_ARM_EEF) #include "lpc1768/pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768#elif MB(RAMPS_14_RE_ARM_SF) #include "lpc1768/pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768#elif MB(MKS_SBASE) #include "lpc1768/pins_MKS_SBASE.h" // LPC1768 env:LPC1768#elif MB(MKS_SGEN_L) #include "lpc1768/pins_MKS_SGEN_L.h" // LPC1768 env:LPC1768#elif MB(AZSMZ_MINI) #include "lpc1768/pins_AZSMZ_MINI.h" // LPC1768 env:LPC1768#elif MB(BIQU_BQ111_A4) #include "lpc1768/pins_BIQU_BQ111_A4.h" // LPC1768 env:LPC1768#elif MB(SELENA_COMPACT) #include "lpc1768/pins_SELENA_COMPACT.h" // LPC1768 env:LPC1768#elif MB(BIQU_B300_V1_0) #include "lpc1768/pins_BIQU_B300_V1.0.h" // LPC1768 env:LPC1768#elif MB(GMARSH_X6_REV1) #include "lpc1768/pins_GMARSH_X6_REV1.h" // LPC1768 env:LPC1768#elif MB(BTT_SKR_V1_1) #include "lpc1768/pins_BTT_SKR_V1_1.h" // LPC1768 env:LPC1768#elif MB(BTT_SKR_V1_3) #include "lpc1768/pins_BTT_SKR_V1_3.h" // LPC1768 env:LPC1768#elif MB(BTT_SKR_V1_4) #include "lpc1768/pins_BTT_SKR_V1_4.h" // LPC1768 env:LPC1768
//// LPC1769 ARM Cortex M3//
#elif MB(MKS_SGEN) #include "lpc1769/pins_MKS_SGEN.h" // LPC1769 env:LPC1769#elif MB(AZTEEG_X5_GT) #include "lpc1769/pins_AZTEEG_X5_GT.h" // LPC1769 env:LPC1769#elif MB(AZTEEG_X5_MINI) #include "lpc1769/pins_AZTEEG_X5_MINI.h" // LPC1769 env:LPC1769#elif MB(AZTEEG_X5_MINI_WIFI) #include "lpc1769/pins_AZTEEG_X5_MINI_WIFI.h" // LPC1769 env:LPC1769#elif MB(COHESION3D_REMIX) #include "lpc1769/pins_COHESION3D_REMIX.h" // LPC1769 env:LPC1769#elif MB(COHESION3D_MINI) #include "lpc1769/pins_COHESION3D_MINI.h" // LPC1769 env:LPC1769#elif MB(SMOOTHIEBOARD) #include "lpc1769/pins_SMOOTHIEBOARD.h" // LPC1769 env:LPC1769#elif MB(TH3D_EZBOARD) #include "lpc1769/pins_TH3D_EZBOARD.h" // LPC1769 env:LPC1769#elif MB(BTT_SKR_V1_4_TURBO) #include "lpc1769/pins_BTT_SKR_V1_4_TURBO.h" // LPC1769 env:LPC1769#elif MB(MKS_SGEN_L_V2) #include "lpc1769/pins_MKS_SGEN_L_V2.h" // LPC1769 env:LPC1769#elif MB(BTT_SKR_E3_TURBO) #include "lpc1769/pins_BTT_SKR_E3_TURBO.h" // LPC1769 env:LPC1769
//// Due (ATSAM) boards//
#elif MB(DUE3DOM) #include "sam/pins_DUE3DOM.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(DUE3DOM_MINI) #include "sam/pins_DUE3DOM_MINI.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RADDS) #include "sam/pins_RADDS.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RURAMPS4D_11) #include "sam/pins_RURAMPS4D_11.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RURAMPS4D_13) #include "sam/pins_RURAMPS4D_13.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS_FD_V1) #include "sam/pins_RAMPS_FD_V1.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS_FD_V2) #include "sam/pins_RAMPS_FD_V2.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS_SMART_EFB) #include "sam/pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS_SMART_EEB) #include "sam/pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS_SMART_EFF) #include "sam/pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS_SMART_EEF) #include "sam/pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS_SMART_SF) #include "sam/pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS_DUO_EFB) #include "sam/pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS_DUO_EEB) #include "sam/pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS_DUO_EFF) #include "sam/pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS_DUO_EEF) #include "sam/pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS_DUO_SF) #include "sam/pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS4DUE_EFB) #include "sam/pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS4DUE_EEB) #include "sam/pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS4DUE_EFF) #include "sam/pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS4DUE_EEF) #include "sam/pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(RAMPS4DUE_SF) #include "sam/pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug#elif MB(ULTRATRONICS_PRO) #include "sam/pins_ULTRATRONICS_PRO.h" // SAM3X8E env:DUE env:DUE_debug#elif MB(ARCHIM1) #include "sam/pins_ARCHIM1.h" // SAM3X8E env:DUE env:DUE_debug#elif MB(ARCHIM2) #include "sam/pins_ARCHIM2.h" // SAM3X8E env:DUE_archim env:DUE_archim_debug#elif MB(ALLIGATOR) #include "sam/pins_ALLIGATOR_R2.h" // SAM3X8E env:DUE env:DUE_debug#elif MB(ADSK) #include "sam/pins_ADSK.h" // SAM3X8E env:DUE env:DUE_debug#elif MB(PRINTRBOARD_G2) #include "sam/pins_PRINTRBOARD_G2.h" // SAM3X8C env:DUE_USB#elif MB(CNCONTROLS_15D) #include "sam/pins_CNCONTROLS_15D.h" // SAM3X8E env:DUE env:DUE_USB
//// STM32 ARM Cortex-M0//#elif MB(MALYAN_M200_V2) #include "stm32f0/pins_MALYAN_M200_V2.h" // STM32F0 env:STM32F070RB_malyan env:STM32F070CB_malyan#elif MB(MALYAN_M300) #include "stm32f0/pins_MALYAN_M300.h" // STM32F070 env:malyan_M300
//// STM32 ARM Cortex-M3//
#elif MB(STM32F103RE) #include "stm32f1/pins_STM32F1R.h" // STM32F1 env:STM32F103RE#elif MB(MALYAN_M200) #include "stm32f1/pins_MALYAN_M200.h" // STM32F1 env:STM32F103CB_malyan#elif MB(STM3R_MINI) #include "stm32f1/pins_STM3R_MINI.h" // STM32F1 env:STM32F103RE#elif MB(GTM32_PRO_VB) #include "stm32f1/pins_GTM32_PRO_VB.h" // STM32F1 env:STM32F103RE#elif MB(GTM32_MINI) #include "stm32f1/pins_GTM32_MINI.h" // STM32F1 env:STM32F103RE#elif MB(GTM32_MINI_A30) #include "stm32f1/pins_GTM32_MINI_A30.h" // STM32F1 env:STM32F103RE#elif MB(GTM32_REV_B) #include "stm32f1/pins_GTM32_REV_B.h" // STM32F1 env:STM32F103RE#elif MB(MORPHEUS) #include "stm32f1/pins_MORPHEUS.h" // STM32F1 env:STM32F103RE#elif MB(CHITU3D) #include "stm32f1/pins_CHITU3D.h" // STM32F1 env:STM32F103RE#elif MB(MKS_ROBIN) #include "stm32f1/pins_MKS_ROBIN.h" // STM32F1 env:mks_robin env:mks_robin_stm32#elif MB(MKS_ROBIN_MINI) #include "stm32f1/pins_MKS_ROBIN_MINI.h" // STM32F1 env:mks_robin_mini#elif MB(MKS_ROBIN_NANO) #include "stm32f1/pins_MKS_ROBIN_NANO.h" // STM32F1 env:mks_robin_nano35#elif MB(MKS_ROBIN_NANO_V2) #include "stm32f1/pins_MKS_ROBIN_NANO_V2.h" // STM32F1 env:mks_robin_nano35#elif MB(MKS_ROBIN_LITE) #include "stm32f1/pins_MKS_ROBIN_LITE.h" // STM32F1 env:mks_robin_lite#elif MB(MKS_ROBIN_LITE3) #include "stm32f1/pins_MKS_ROBIN_LITE3.h" // STM32F1 env:mks_robin_lite3#elif MB(MKS_ROBIN_PRO) #include "stm32f1/pins_MKS_ROBIN_PRO.h" // STM32F1 env:mks_robin_pro#elif MB(MKS_ROBIN_E3) #include "stm32f1/pins_MKS_ROBIN_E3.h" // STM32F1 env:mks_robin_e3#elif MB(MKS_ROBIN_E3D) #include "stm32f1/pins_MKS_ROBIN_E3D.h" // STM32F1 env:mks_robin_e3#elif MB(MKS_ROBIN_E3P) #include "stm32f1/pins_MKS_ROBIN_E3P.h" // STM32F1 env:mks_robin_e3p#elif MB(BTT_SKR_MINI_V1_1) #include "stm32f1/pins_BTT_SKR_MINI_V1_1.h" // STM32F1 env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB#elif MB(BTT_SKR_MINI_E3_V1_0) #include "stm32f1/pins_BTT_SKR_MINI_E3_V1_0.h" // STM32F1 env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB#elif MB(BTT_SKR_MINI_E3_V1_2) #include "stm32f1/pins_BTT_SKR_MINI_E3_V1_2.h" // STM32F1 env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB#elif MB(BTT_SKR_MINI_E3_V2_0) #include "stm32f1/pins_BTT_SKR_MINI_E3_V2_0.h" // STM32F1 env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB#elif MB(BTT_SKR_E3_DIP) #include "stm32f1/pins_BTT_SKR_E3_DIP.h" // STM32F1 env:STM32F103RE_btt env:STM32F103RE_btt_USB env:STM32F103RC_btt env:STM32F103RC_btt_512K env:STM32F103RC_btt_USB env:STM32F103RC_btt_512K_USB#elif MB(JGAURORA_A5S_A1) #include "stm32f1/pins_JGAURORA_A5S_A1.h" // STM32F1 env:jgaurora_a5s_a1#elif MB(FYSETC_AIO_II) #include "stm32f1/pins_FYSETC_AIO_II.h" // STM32F1 env:STM32F103RC_fysetc#elif MB(FYSETC_CHEETAH) #include "stm32f1/pins_FYSETC_CHEETAH.h" // STM32F1 env:STM32F103RC_fysetc#elif MB(FYSETC_CHEETAH_V12) #include "stm32f1/pins_FYSETC_CHEETAH_V12.h" // STM32F1 env:STM32F103RC_fysetc#elif MB(LONGER3D_LK) #include "stm32f1/pins_LONGER3D_LK.h" // STM32F1 env:STM32F103VE_longer#elif MB(CCROBOT_MEEB_3DP) #include "stm32f1/pins_CCROBOT_MEEB_3DP.h" // STM32F1 env:STM32F103RC_meeb#elif MB(CHITU3D_V5) #include "stm32f1/pins_CHITU3D_V5.h" // STM32F1 env:chitu_f103 env:chitu_v5_gpio_init#elif MB(CHITU3D_V6) #include "stm32f1/pins_CHITU3D_V6.h" // STM32F1 env:chitu_f103#elif MB(CREALITY_V4) #include "stm32f1/pins_CREALITY_V4.h" // STM32F1 env:STM32F103RET6_creality#elif MB(CREALITY_V427) #include "stm32f1/pins_CREALITY_V427.h" // STM32F1 env:STM32F103RET6_creality#elif MB(TRIGORILLA_PRO) #include "stm32f1/pins_TRIGORILLA_PRO.h" // STM32F1 env:trigorilla_pro#elif MB(FLY_MINI) #include "stm32f1/pins_FLY_MINI.h" // STM32F1 env:FLY_MINI
//// ARM Cortex-M4F//
#elif MB(TEENSY31_32) #include "teensy3/pins_TEENSY31_32.h" // TEENSY31_32 env:teensy31#elif MB(TEENSY35_36) #include "teensy3/pins_TEENSY35_36.h" // TEENSY35_36 env:teensy35
//// STM32 ARM Cortex-M4F//
#elif MB(BEAST) #include "stm32f4/pins_BEAST.h" // STM32F4 env:STM32F4#elif MB(GENERIC_STM32F4) #include "stm32f4/pins_GENERIC_STM32F4.h" // STM32F4 env:STM32F4#elif MB(ARMED) #include "stm32f4/pins_ARMED.h" // STM32F4 env:ARMED#elif MB(RUMBA32_V1_0) #include "stm32f4/pins_RUMBA32_AUS3D.h" // STM32F4 env:rumba32#elif MB(RUMBA32_V1_1) #include "stm32f4/pins_RUMBA32_AUS3D.h" // STM32F4 env:rumba32#elif MB(RUMBA32_MKS) #include "stm32f4/pins_RUMBA32_MKS.h" // STM32F4 env:rumba32#elif MB(BLACK_STM32F407VE) #include "stm32f4/pins_BLACK_STM32F407VE.h" // STM32F4 env:STM32F407VE_black#elif MB(STEVAL_3DP001V1) #include "stm32f4/pins_STEVAL_3DP001V1.h" // STM32F4 env:STM32F401VE_STEVAL#elif MB(BTT_SKR_PRO_V1_1) #include "stm32f4/pins_BTT_SKR_PRO_V1_1.h" // STM32F4 env:BIGTREE_SKR_PRO#elif MB(BTT_SKR_PRO_V1_2) #include "stm32f4/pins_BTT_SKR_PRO_V1_2.h" // STM32F4 env:BIGTREE_SKR_PRO#elif MB(BTT_GTR_V1_0) #include "stm32f4/pins_BTT_GTR_V1_0.h" // STM32F4 env:BIGTREE_GTR_V1_0#elif MB(BTT_BTT002_V1_0) #include "stm32f4/pins_BTT_BTT002_V1_0.h" // STM32F4 env:BIGTREE_BTT002#elif MB(LERDGE_K) #include "stm32f4/pins_LERDGE_K.h" // STM32F4 env:STM32F4#elif MB(LERDGE_S) #include "stm32f4/pins_LERDGE_S.h" // STM32F4 env:LERDGE_S#elif MB(LERDGE_X) #include "stm32f4/pins_LERDGE_X.h" // STM32F4 env:LERDGE_X#elif MB(VAKE403D) #include "stm32f4/pins_VAKE403D.h" // STM32F4 env:STM32F4#elif MB(FYSETC_S6) #include "stm32f4/pins_FYSETC_S6.h" // STM32F4 env:FYSETC_S6#elif MB(FLYF407ZG) #include "stm32f4/pins_FLYF407ZG.h" // STM32F4 env:FLYF407ZG#elif MB(MKS_ROBIN2) #include "stm32f4/pins_MKS_ROBIN2.h" // STM32F4 env:MKS_ROBIN2#elif MB(FYSETC_S6_V2_0) #include "stm32f4/pins_FYSETC_S6_V2_0.h" // STM32F4 env:FYSETC_S6
//// ARM Cortex M7//
#elif MB(THE_BORG) #include "stm32f7/pins_THE_BORG.h" // STM32F7 env:STM32F7#elif MB(REMRAM_V1) #include "stm32f7/pins_REMRAM_V1.h" // STM32F7 env:STM32F7#elif MB(NUCLEO_F767ZI) #include "stm32f7/pins_NUCLEO_F767ZI.h" // STM32F7 env:NUCLEO_F767ZI#elif MB(TEENSY41) #include "teensy4/pins_TEENSY41.h" // Teensy-4.x env:teensy41#elif MB(T41U5XBB) #include "teensy4/pins_T41U5XBB.h" // Teensy-4.x env:teensy41
//// Espressif ESP32//
#elif MB(ESPRESSIF_ESP32) #include "esp32/pins_ESP32.h" // ESP32 env:esp32#elif MB(MRR_ESPA) #include "esp32/pins_MRR_ESPA.h" // ESP32 env:esp32#elif MB(MRR_ESPE) #include "esp32/pins_MRR_ESPE.h" // ESP32 env:esp32#elif MB(E4D_BOX) #include "esp32/pins_E4D.h" // ESP32 env:esp32
//// Adafruit Grand Central M4 (SAMD51 ARM Cortex-M4)//
#elif MB(AGCM4_RAMPS_144) #include "samd/pins_RAMPS_144.h" // SAMD51 env:SAMD51_grandcentral_m4
//// Custom board (with custom PIO env)//#elif MB(CUSTOM) #include "pins_custom.h" // env:custom
//// Linux Native Debug board//
#elif MB(LINUX_RAMPS) #include "linux/pins_RAMPS_LINUX.h" // Linux env:linux_native
#else
// // Obsolete or unknown board //
#define BOARD_MKS_13 -1000 #define BOARD_TRIGORILLA -1001 #define BOARD_RURAMPS4D -1002 #define BOARD_FORMBOT_TREX2 -1003 #define BOARD_BIQU_SKR_V1_1 -1004 #define BOARD_STM32F1R -1005 #define BOARD_STM32F103R -1006 #define BOARD_ESP32 -1007 #define BOARD_STEVAL -1008 #define BOARD_BIGTREE_SKR_V1_1 -1009 #define BOARD_BIGTREE_SKR_V1_3 -1010 #define BOARD_BIGTREE_SKR_V1_4 -1011 #define BOARD_BIGTREE_SKR_V1_4_TURBO -1012 #define BOARD_BIGTREE_BTT002_V1_0 -1013 #define BOARD_BIGTREE_SKR_PRO_V1_1 -1014 #define BOARD_BIGTREE_SKR_MINI_V1_1 -1015 #define BOARD_BIGTREE_SKR_MINI_E3 -1016 #define BOARD_BIGTREE_SKR_E3_DIP -1017 #define BOARD_RUMBA32 -1018 #define BOARD_RUMBA32_AUS3D -1019
#if MB(MKS_13) #error "BOARD_MKS_13 has been renamed BOARD_MKS_GEN_13. Please update your configuration." #elif MB(TRIGORILLA) #error "BOARD_TRIGORILLA has been renamed BOARD_TRIGORILLA_13. Please update your configuration." #elif MB(RURAMPS4D) #error "BOARD_RURAMPS4D has been renamed BOARD_RURAMPS4D_11. Please update your configuration." #elif MB(FORMBOT_TREX2) #error "FORMBOT_TREX2 has been renamed BOARD_FORMBOT_TREX2PLUS. Please update your configuration." #elif MB(BIQU_SKR_V1_1) #error "BOARD_BIQU_SKR_V1_1 has been renamed BOARD_BTT_SKR_V1_1. Please update your configuration." #elif MB(BIGTREE_SKR_V1_1) #error "BOARD_BIGTREE_SKR_V1_1 has been renamed BOARD_BTT_SKR_V1_1. Please update your configuration." #elif MB(BIGTREE_SKR_V2_2) #error "BOARD_BIGTREE_SKR_V1_2 has been renamed BOARD_BTT_SKR_V1_2. Please update your configuration." #elif MB(BIGTREE_SKR_V1_3) #error "BOARD_BIGTREE_SKR_V1_3 has been renamed BOARD_BTT_SKR_V1_3. Please update your configuration." #elif MB(BIGTREE_SKR_V1_4) #error "BOARD_BIGTREE_SKR_V1_4 has been renamed BOARD_BTT_SKR_V1_4. Please update your configuration." #elif MB(BIGTREE_SKR_V1_4_TURBO) #error "BOARD_BIGTREE_SKR_V1_4_TURBO has been renamed BOARD_BTT_SKR_V1_4_TURBO. Please update your configuration." #elif MB(BIGTREE_BTT002_V1_0) #error "BOARD_BIGTREE_BTT002_V1_0 has been renamed BOARD_BTT_BTT002_V1_0. Please update your configuration." #elif MB(BIGTREE_SKR_PRO_V1_1) #error "BOARD_BIGTREE_SKR_PRO_V1_1 has been renamed BOARD_BTT_SKR_PRO_V1_1. Please update your configuration." #elif MB(BIGTREE_SKR_MINI_V1_1) #error "BOARD_BIGTREE_SKR_MINI_V1_1 has been renamed BOARD_BTT_SKR_MINI_V1_1. Please update your configuration." #elif MB(BIGTREE_SKR_MINI_E3) #error "BOARD_BIGTREE_SKR_MINI_E3 has been renamed BOARD_BTT_SKR_MINI_E3_V1_0. Please update your configuration." #elif MB(BIGTREE_SKR_E3_DIP) #error "BOARD_BIGTREE_SKR_E3_DIP has been renamed BOARD_BTT_SKR_E3_DIP. Please update your configuration." #elif MB(STM32F1R) #error "BOARD_STM32F1R has been renamed BOARD_STM32F103RE. Please update your configuration." #elif MB(STM32F103R) #error "BOARD_STM32F103R has been renamed BOARD_STM32F103RE. Please update your configuration." #elif MOTHERBOARD == BOARD_ESP32 #error "BOARD_ESP32 has been renamed BOARD_ESPRESSIF_ESP32. Please update your configuration." #elif MB(STEVAL) #error "BOARD_STEVAL has been renamed BOARD_STEVAL_3DP001V1. Please update your configuration." #elif MB(RUMBA32) #error "BOARD_RUMBA32 is now BOARD_RUMBA32_MKS or BOARD_RUMBA32_V1_0. Please update your configuration." #elif MB(RUMBA32_AUS3D) #error "BOARD_RUMBA32_AUS3D is now BOARD_RUMBA32_V1_0. Please update your configuration." #else #error "Unknown MOTHERBOARD value set in Configuration.h" #endif
#undef BOARD_MKS_13 #undef BOARD_TRIGORILLA #undef BOARD_RURAMPS4D #undef BOARD_FORMBOT_TREX2 #undef BOARD_BIQU_SKR_V1_1 #undef BOARD_STM32F1R #undef BOARD_STM32F103R #undef BOARD_ESP32 #undef BOARD_STEVAL #undef BOARD_BIGTREE_SKR_MINI_E3 #undef BOARD_BIGTREE_SKR_V1_1 #undef BOARD_BIGTREE_SKR_V1_3 #undef BOARD_BIGTREE_SKR_V1_4 #undef BOARD_BIGTREE_SKR_V1_4_TURBO #undef BOARD_BIGTREE_BTT002_V1_0 #undef BOARD_BIGTREE_SKR_PRO_V1_1 #undef BOARD_BIGTREE_SKR_MINI_V1_1 #undef BOARD_BIGTREE_SKR_E3_DIP #undef BOARD_RUMBA32 #undef BOARD_RUMBA32_AUS3D
#endif
// Define certain undefined pins#ifndef X_MS1_PIN #define X_MS1_PIN -1#endif#ifndef X_MS2_PIN #define X_MS2_PIN -1#endif#ifndef X_MS3_PIN #define X_MS3_PIN -1#endif#ifndef Y_MS1_PIN #define Y_MS1_PIN -1#endif#ifndef Y_MS2_PIN #define Y_MS2_PIN -1#endif#ifndef Y_MS3_PIN #define Y_MS3_PIN -1#endif#ifndef Z_MS1_PIN #define Z_MS1_PIN -1#endif#ifndef Z_MS2_PIN #define Z_MS2_PIN -1#endif#ifndef Z_MS3_PIN #define Z_MS3_PIN -1#endif#ifndef E0_MS1_PIN #define E0_MS1_PIN -1#endif#ifndef E0_MS2_PIN #define E0_MS2_PIN -1#endif#ifndef E0_MS3_PIN #define E0_MS3_PIN -1#endif#ifndef E1_MS1_PIN #define E1_MS1_PIN -1#endif#ifndef E1_MS2_PIN #define E1_MS2_PIN -1#endif#ifndef E1_MS3_PIN #define E1_MS3_PIN -1#endif#ifndef E2_MS1_PIN #define E2_MS1_PIN -1#endif#ifndef E2_MS2_PIN #define E2_MS2_PIN -1#endif#ifndef E2_MS3_PIN #define E2_MS3_PIN -1#endif#ifndef E3_MS1_PIN #define E3_MS1_PIN -1#endif#ifndef E3_MS2_PIN #define E3_MS2_PIN -1#endif#ifndef E3_MS3_PIN #define E3_MS3_PIN -1#endif#ifndef E4_MS1_PIN #define E4_MS1_PIN -1#endif#ifndef E4_MS2_PIN #define E4_MS2_PIN -1#endif#ifndef E4_MS3_PIN #define E4_MS3_PIN -1#endif#ifndef E5_MS1_PIN #define E5_MS1_PIN -1#endif#ifndef E5_MS2_PIN #define E5_MS2_PIN -1#endif#ifndef E5_MS3_PIN #define E5_MS3_PIN -1#endif#ifndef E6_MS1_PIN #define E6_MS1_PIN -1#endif#ifndef E6_MS2_PIN #define E6_MS2_PIN -1#endif#ifndef E6_MS3_PIN #define E6_MS3_PIN -1#endif#ifndef E7_MS1_PIN #define E7_MS1_PIN -1#endif#ifndef E7_MS2_PIN #define E7_MS2_PIN -1#endif#ifndef E7_MS3_PIN #define E7_MS3_PIN -1#endif
#ifndef E0_STEP_PIN #define E0_STEP_PIN -1#endif#ifndef E0_DIR_PIN #define E0_DIR_PIN -1#endif#ifndef E0_ENABLE_PIN #define E0_ENABLE_PIN -1#endif#ifndef E1_STEP_PIN #define E1_STEP_PIN -1#endif#ifndef E1_DIR_PIN #define E1_DIR_PIN -1#endif#ifndef E1_ENABLE_PIN #define E1_ENABLE_PIN -1#endif#ifndef E2_STEP_PIN #define E2_STEP_PIN -1#endif#ifndef E2_DIR_PIN #define E2_DIR_PIN -1#endif#ifndef E2_ENABLE_PIN #define E2_ENABLE_PIN -1#endif#ifndef E3_STEP_PIN #define E3_STEP_PIN -1#endif#ifndef E3_DIR_PIN #define E3_DIR_PIN -1#endif#ifndef E3_ENABLE_PIN #define E3_ENABLE_PIN -1#endif#ifndef E4_STEP_PIN #define E4_STEP_PIN -1#endif#ifndef E4_DIR_PIN #define E4_DIR_PIN -1#endif#ifndef E4_ENABLE_PIN #define E4_ENABLE_PIN -1#endif#ifndef E5_STEP_PIN #define E5_STEP_PIN -1#endif#ifndef E5_DIR_PIN #define E5_DIR_PIN -1#endif#ifndef E5_ENABLE_PIN #define E5_ENABLE_PIN -1#endif#ifndef E6_STEP_PIN #define E6_STEP_PIN -1#endif#ifndef E6_DIR_PIN #define E6_DIR_PIN -1#endif#ifndef E6_ENABLE_PIN #define E6_ENABLE_PIN -1#endif#ifndef E7_STEP_PIN #define E7_STEP_PIN -1#endif#ifndef E7_DIR_PIN #define E7_DIR_PIN -1#endif#ifndef E7_ENABLE_PIN #define E7_ENABLE_PIN -1#endif
//// Destroy unused CS pins//#if !AXIS_HAS_SPI(X) #undef X_CS_PIN#endif#if !AXIS_HAS_SPI(Y) #undef Y_CS_PIN#endif#if !AXIS_HAS_SPI(Z) #undef Z_CS_PIN#endif#if E_STEPPERS && !AXIS_HAS_SPI(E0) #undef E0_CS_PIN#endif#if E_STEPPERS > 1 && !AXIS_HAS_SPI(E1) #undef E1_CS_PIN#endif#if E_STEPPERS > 2 && !AXIS_HAS_SPI(E2) #undef E2_CS_PIN#endif#if E_STEPPERS > 3 && !AXIS_HAS_SPI(E3) #undef E3_CS_PIN#endif#if E_STEPPERS > 4 && !AXIS_HAS_SPI(E4) #undef E4_CS_PIN#endif#if E_STEPPERS > 5 && !AXIS_HAS_SPI(E5) #undef E5_CS_PIN#endif#if E_STEPPERS > 6 && !AXIS_HAS_SPI(E6) #undef E6_CS_PIN#endif#if E_STEPPERS > 7 && !AXIS_HAS_SPI(E7) #undef E7_CS_PIN#endif
#ifndef X_CS_PIN #define X_CS_PIN -1#endif#ifndef Y_CS_PIN #define Y_CS_PIN -1#endif#ifndef Z_CS_PIN #define Z_CS_PIN -1#endif#ifndef E0_CS_PIN #define E0_CS_PIN -1#endif#ifndef E1_CS_PIN #define E1_CS_PIN -1#endif#ifndef E2_CS_PIN #define E2_CS_PIN -1#endif#ifndef E3_CS_PIN #define E3_CS_PIN -1#endif#ifndef E4_CS_PIN #define E4_CS_PIN -1#endif#ifndef E5_CS_PIN #define E5_CS_PIN -1#endif#ifndef E6_CS_PIN #define E6_CS_PIN -1#endif#ifndef E7_CS_PIN #define E7_CS_PIN -1#endif
#ifndef FAN_PIN #define FAN_PIN -1#endif#define FAN0_PIN FAN_PIN#ifndef FAN1_PIN #define FAN1_PIN -1#endif#ifndef FAN2_PIN #define FAN2_PIN -1#endif#ifndef CONTROLLER_FAN_PIN #define CONTROLLER_FAN_PIN -1#endif
#ifndef FANMUX0_PIN #define FANMUX0_PIN -1#endif#ifndef FANMUX1_PIN #define FANMUX1_PIN -1#endif#ifndef FANMUX2_PIN #define FANMUX2_PIN -1#endif
#ifndef HEATER_0_PIN #define HEATER_0_PIN -1#endif#ifndef HEATER_1_PIN #define HEATER_1_PIN -1#endif#ifndef HEATER_2_PIN #define HEATER_2_PIN -1#endif#ifndef HEATER_3_PIN #define HEATER_3_PIN -1#endif#ifndef HEATER_4_PIN #define HEATER_4_PIN -1#endif#ifndef HEATER_5_PIN #define HEATER_5_PIN -1#endif#ifndef HEATER_6_PIN #define HEATER_6_PIN -1#endif#ifndef HEATER_7_PIN #define HEATER_7_PIN -1#endif#ifndef HEATER_BED_PIN #define HEATER_BED_PIN -1#endif
#ifndef TEMP_0_PIN #define TEMP_0_PIN -1#endif#ifndef TEMP_1_PIN #define TEMP_1_PIN -1#endif#ifndef TEMP_2_PIN #define TEMP_2_PIN -1#endif#ifndef TEMP_3_PIN #define TEMP_3_PIN -1#endif#ifndef TEMP_4_PIN #define TEMP_4_PIN -1#endif#ifndef TEMP_5_PIN #define TEMP_5_PIN -1#endif#ifndef TEMP_6_PIN #define TEMP_6_PIN -1#endif#ifndef TEMP_7_PIN #define TEMP_7_PIN -1#endif#ifndef TEMP_BED_PIN #define TEMP_BED_PIN -1#endif
#ifndef SD_DETECT_PIN #define SD_DETECT_PIN -1#endif#ifndef SDPOWER_PIN #define SDPOWER_PIN -1#endif#ifndef SDSS #define SDSS -1#endif#ifndef LED_PIN #define LED_PIN -1#endif#if DISABLED(PSU_CONTROL) || !defined(PS_ON_PIN) #undef PS_ON_PIN #define PS_ON_PIN -1#endif#ifndef KILL_PIN #define KILL_PIN -1#endif#ifndef SUICIDE_PIN #define SUICIDE_PIN -1#endif#ifndef SUICIDE_PIN_INVERTING #define SUICIDE_PIN_INVERTING false#endif
#ifndef NUM_SERVO_PLUGS #define NUM_SERVO_PLUGS 4#endif
//// Assign endstop pins for boards with only 3 connectors//#ifdef X_STOP_PIN #if X_HOME_DIR < 0 #define X_MIN_PIN X_STOP_PIN #ifndef X_MAX_PIN #define X_MAX_PIN -1 #endif #else #define X_MAX_PIN X_STOP_PIN #ifndef X_MIN_PIN #define X_MIN_PIN -1 #endif #endif#elif X_HOME_DIR < 0 #define X_STOP_PIN X_MIN_PIN#else #define X_STOP_PIN X_MAX_PIN#endif
#ifdef Y_STOP_PIN #if Y_HOME_DIR < 0 #define Y_MIN_PIN Y_STOP_PIN #ifndef Y_MAX_PIN #define Y_MAX_PIN -1 #endif #else #define Y_MAX_PIN Y_STOP_PIN #ifndef Y_MIN_PIN #define Y_MIN_PIN -1 #endif #endif#elif Y_HOME_DIR < 0 #define Y_STOP_PIN Y_MIN_PIN#else #define Y_STOP_PIN Y_MAX_PIN#endif
#ifdef Z_STOP_PIN #if Z_HOME_DIR < 0 #define Z_MIN_PIN Z_STOP_PIN #ifndef Z_MAX_PIN #define Z_MAX_PIN -1 #endif #else #define Z_MAX_PIN Z_STOP_PIN #ifndef Z_MIN_PIN #define Z_MIN_PIN -1 #endif #endif#elif Z_HOME_DIR < 0 #define Z_STOP_PIN Z_MIN_PIN#else #define Z_STOP_PIN Z_MAX_PIN#endif
//// Disable unused endstop / probe pins//#if !HAS_CUSTOM_PROBE_PIN #undef Z_MIN_PROBE_PIN #define Z_MIN_PROBE_PIN -1#endif
#if DISABLED(USE_XMAX_PLUG) #undef X_MAX_PIN #define X_MAX_PIN -1#endif
#if DISABLED(USE_YMAX_PLUG) #undef Y_MAX_PIN #define Y_MAX_PIN -1#endif
#if DISABLED(USE_ZMAX_PLUG) #undef Z_MAX_PIN #define Z_MAX_PIN -1#endif
#if DISABLED(USE_XMIN_PLUG) #undef X_MIN_PIN #define X_MIN_PIN -1#endif
#if DISABLED(USE_YMIN_PLUG) #undef Y_MIN_PIN #define Y_MIN_PIN -1#endif
#if DISABLED(USE_ZMIN_PLUG) #undef Z_MIN_PIN #define Z_MIN_PIN -1#endif
#if HAS_FILAMENT_SENSOR #define FIL_RUNOUT1_PIN FIL_RUNOUT_PIN#else #undef FIL_RUNOUT_PIN #undef FIL_RUNOUT1_PIN#endif
#ifndef LCD_PINS_D4 #define LCD_PINS_D4 -1#endif
#if HAS_MARLINUI_HD44780 || TOUCH_UI_ULTIPANEL #ifndef LCD_PINS_D5 #define LCD_PINS_D5 -1 #endif #ifndef LCD_PINS_D6 #define LCD_PINS_D6 -1 #endif #ifndef LCD_PINS_D7 #define LCD_PINS_D7 -1 #endif#endif
/** * Auto-Assignment for Dual X, Dual Y, Multi-Z Steppers * * By default X2 is assigned to the next open E plug * on the board, then in order, Y2, Z2, Z3. These can be * overridden in Configuration.h or Configuration_adv.h. */
#define __PEXI(p,q) PIN_EXISTS(E##p##_##q)#define _PEXI(p,q) __PEXI(p,q)#define __EPIN(p,q) E##p##_##q##_PIN#define _EPIN(p,q) __EPIN(p,q)#define DIAG_REMAPPED(p,q) (PIN_EXISTS(q) && _EPIN(p##_E_INDEX, DIAG) == q##_PIN)
// The X2 axis, if any, should be the next open extruder port#define X2_E_INDEX E_STEPPERS
#if EITHER(DUAL_X_CARRIAGE, X_DUAL_STEPPER_DRIVERS) #ifndef X2_STEP_PIN #define X2_STEP_PIN _EPIN(X2_E_INDEX, STEP) #define X2_DIR_PIN _EPIN(X2_E_INDEX, DIR) #define X2_ENABLE_PIN _EPIN(X2_E_INDEX, ENABLE) #if X2_E_INDEX >= MAX_EXTRUDERS || !PIN_EXISTS(X2_STEP) #error "No E stepper plug left for X2!" #endif #endif #ifndef X2_MS1_PIN #define X2_MS1_PIN _EPIN(X2_E_INDEX, MS1) #endif #ifndef X2_MS2_PIN #define X2_MS2_PIN _EPIN(X2_E_INDEX, MS2) #endif #ifndef X2_MS3_PIN #define X2_MS3_PIN _EPIN(X2_E_INDEX, MS3) #endif #if AXIS_HAS_SPI(X2) && !defined(X2_CS_PIN) #define X2_CS_PIN _EPIN(X2_E_INDEX, CS) #endif #if AXIS_HAS_UART(X2) #ifndef X2_SERIAL_TX_PIN #define X2_SERIAL_TX_PIN _EPIN(X2_E_INDEX, SERIAL_TX) #endif #ifndef X2_SERIAL_RX_PIN #define X2_SERIAL_RX_PIN _EPIN(X2_E_INDEX, SERIAL_RX) #endif #endif
// // Auto-assign pins for stallGuard sensorless homing // #if defined(X2_STALL_SENSITIVITY) && ENABLED(X_DUAL_ENDSTOPS) && _PEXI(X2_E_INDEX, DIAG) #define X2_DIAG_PIN _EPIN(X2_E_INDEX, DIAG) #if DIAG_REMAPPED(X2, X_MIN) // If already remapped in the pins file... #define X2_USE_ENDSTOP _XMIN_ #elif DIAG_REMAPPED(X2, Y_MIN) #define X2_USE_ENDSTOP _YMIN_ #elif DIAG_REMAPPED(X2, Z_MIN) #define X2_USE_ENDSTOP _ZMIN_ #elif DIAG_REMAPPED(X2, X_MAX) #define X2_USE_ENDSTOP _XMAX_ #elif DIAG_REMAPPED(X2, Y_MAX) #define X2_USE_ENDSTOP _YMAX_ #elif DIAG_REMAPPED(X2, Z_MAX) #define X2_USE_ENDSTOP _ZMAX_ #else // Otherwise use the driver DIAG_PIN directly #define _X2_USE_ENDSTOP(P) _E##P##_DIAG_ #define X2_USE_ENDSTOP _X2_USE_ENDSTOP(X2_E_INDEX) #endif #undef X2_DIAG_PIN #endif
#define Y2_E_INDEX INCREMENT(X2_E_INDEX)#else #define Y2_E_INDEX X2_E_INDEX#endif
#ifndef X2_CS_PIN #define X2_CS_PIN -1#endif#ifndef X2_MS1_PIN #define X2_MS1_PIN -1#endif#ifndef X2_MS2_PIN #define X2_MS2_PIN -1#endif#ifndef X2_MS3_PIN #define X2_MS3_PIN -1#endif
// The Y2 axis, if any, should be the next open extruder port#if ENABLED(Y_DUAL_STEPPER_DRIVERS) #ifndef Y2_STEP_PIN #define Y2_STEP_PIN _EPIN(Y2_E_INDEX, STEP) #define Y2_DIR_PIN _EPIN(Y2_E_INDEX, DIR) #define Y2_ENABLE_PIN _EPIN(Y2_E_INDEX, ENABLE) #if Y2_E_INDEX >= MAX_EXTRUDERS || !PIN_EXISTS(Y2_STEP) #error "No E stepper plug left for Y2!" #endif #endif #ifndef Y2_MS1_PIN #define Y2_MS1_PIN _EPIN(Y2_E_INDEX, MS1) #endif #ifndef Y2_MS2_PIN #define Y2_MS2_PIN _EPIN(Y2_E_INDEX, MS2) #endif #ifndef Y2_MS3_PIN #define Y2_MS3_PIN _EPIN(Y2_E_INDEX, MS3) #endif #if AXIS_HAS_SPI(Y2) && !defined(Y2_CS_PIN) #define Y2_CS_PIN _EPIN(Y2_E_INDEX, CS) #endif #if AXIS_HAS_UART(Y2) #ifndef Y2_SERIAL_TX_PIN #define Y2_SERIAL_TX_PIN _EPIN(Y2_E_INDEX, SERIAL_TX) #endif #ifndef Y2_SERIAL_RX_PIN #define Y2_SERIAL_RX_PIN _EPIN(Y2_E_INDEX, SERIAL_RX) #endif #endif #if defined(Y2_STALL_SENSITIVITY) && ENABLED(Y_DUAL_ENDSTOPS) && _PEXI(Y2_E_INDEX, DIAG) #define Y2_DIAG_PIN _EPIN(Y2_E_INDEX, DIAG) #if DIAG_REMAPPED(Y2, X_MIN) #define Y2_USE_ENDSTOP _XMIN_ #elif DIAG_REMAPPED(Y2, Y_MIN) #define Y2_USE_ENDSTOP _YMIN_ #elif DIAG_REMAPPED(Y2, Z_MIN) #define Y2_USE_ENDSTOP _ZMIN_ #elif DIAG_REMAPPED(Y2, X_MAX) #define Y2_USE_ENDSTOP _XMAX_ #elif DIAG_REMAPPED(Y2, Y_MAX) #define Y2_USE_ENDSTOP _YMAX_ #elif DIAG_REMAPPED(Y2, Z_MAX) #define Y2_USE_ENDSTOP _ZMAX_ #else #define _Y2_USE_ENDSTOP(P) _E##P##_DIAG_ #define Y2_USE_ENDSTOP _Y2_USE_ENDSTOP(Y2_E_INDEX) #endif #undef Y2_DIAG_PIN #endif #define Z2_E_INDEX INCREMENT(Y2_E_INDEX)#else #define Z2_E_INDEX Y2_E_INDEX#endif
#ifndef Y2_CS_PIN #define Y2_CS_PIN -1#endif#ifndef Y2_MS1_PIN #define Y2_MS1_PIN -1#endif#ifndef Y2_MS2_PIN #define Y2_MS2_PIN -1#endif#ifndef Y2_MS3_PIN #define Y2_MS3_PIN -1#endif
// The Z2 axis, if any, should be the next open extruder port#if NUM_Z_STEPPER_DRIVERS >= 2 #ifndef Z2_STEP_PIN #define Z2_STEP_PIN _EPIN(Z2_E_INDEX, STEP) #define Z2_DIR_PIN _EPIN(Z2_E_INDEX, DIR) #define Z2_ENABLE_PIN _EPIN(Z2_E_INDEX, ENABLE) #if Z2_E_INDEX >= MAX_EXTRUDERS || !PIN_EXISTS(Z2_STEP) #error "No E stepper plug left for Z2!" #endif #endif #ifndef Z2_MS1_PIN #define Z2_MS1_PIN _EPIN(Z2_E_INDEX, MS1) #endif #ifndef Z2_MS2_PIN #define Z2_MS2_PIN _EPIN(Z2_E_INDEX, MS2) #endif #ifndef Z2_MS3_PIN #define Z2_MS3_PIN _EPIN(Z2_E_INDEX, MS3) #endif #if AXIS_HAS_SPI(Z2) && !defined(Z2_CS_PIN) #define Z2_CS_PIN _EPIN(Z2_E_INDEX, CS) #endif #if AXIS_HAS_UART(Z2) #ifndef Z2_SERIAL_TX_PIN #define Z2_SERIAL_TX_PIN _EPIN(Z2_E_INDEX, SERIAL_TX) #endif #ifndef Z2_SERIAL_RX_PIN #define Z2_SERIAL_RX_PIN _EPIN(Z2_E_INDEX, SERIAL_RX) #endif #endif #if defined(Z2_STALL_SENSITIVITY) && ENABLED(Z_MULTI_ENDSTOPS) && NUM_Z_STEPPER_DRIVERS >= 2 && _PEXI(Z2_E_INDEX, DIAG) #define Z2_DIAG_PIN _EPIN(Z2_E_INDEX, DIAG) #if DIAG_REMAPPED(Z2, X_MIN) #define Z2_USE_ENDSTOP _XMIN_ #elif DIAG_REMAPPED(Z2, Y_MIN) #define Z2_USE_ENDSTOP _YMIN_ #elif DIAG_REMAPPED(Z2, Z_MIN) #define Z2_USE_ENDSTOP _ZMIN_ #elif DIAG_REMAPPED(Z2, X_MAX) #define Z2_USE_ENDSTOP _XMAX_ #elif DIAG_REMAPPED(Z2, Y_MAX) #define Z2_USE_ENDSTOP _YMAX_ #elif DIAG_REMAPPED(Z2, Z_MAX) #define Z2_USE_ENDSTOP _ZMAX_ #else #define _Z2_USE_ENDSTOP(P) _E##P##_DIAG_ #define Z2_USE_ENDSTOP _Z2_USE_ENDSTOP(Z2_E_INDEX) #endif #undef Z2_DIAG_PIN #endif #define Z3_E_INDEX INCREMENT(Z2_E_INDEX)#else #define Z3_E_INDEX Z2_E_INDEX#endif
#ifndef Z2_CS_PIN #define Z2_CS_PIN -1#endif#ifndef Z2_MS1_PIN #define Z2_MS1_PIN -1#endif#ifndef Z2_MS2_PIN #define Z2_MS2_PIN -1#endif#ifndef Z2_MS3_PIN #define Z2_MS3_PIN -1#endif
#if NUM_Z_STEPPER_DRIVERS >= 3 #ifndef Z3_STEP_PIN #define Z3_STEP_PIN _EPIN(Z3_E_INDEX, STEP) #define Z3_DIR_PIN _EPIN(Z3_E_INDEX, DIR) #define Z3_ENABLE_PIN _EPIN(Z3_E_INDEX, ENABLE) #if Z3_E_INDEX >= MAX_EXTRUDERS || !PIN_EXISTS(Z3_STEP) #error "No E stepper plug left for Z3!" #endif #endif #if AXIS_HAS_SPI(Z3) #ifndef Z3_CS_PIN #define Z3_CS_PIN _EPIN(Z3_E_INDEX, CS) #endif #endif #ifndef Z3_MS1_PIN #define Z3_MS1_PIN _EPIN(Z3_E_INDEX, MS1) #endif #ifndef Z3_MS2_PIN #define Z3_MS2_PIN _EPIN(Z3_E_INDEX, MS2) #endif #ifndef Z3_MS3_PIN #define Z3_MS3_PIN _EPIN(Z3_E_INDEX, MS3) #endif #if AXIS_HAS_UART(Z3) #ifndef Z3_SERIAL_TX_PIN #define Z3_SERIAL_TX_PIN _EPIN(Z3_E_INDEX, SERIAL_TX) #endif #ifndef Z3_SERIAL_RX_PIN #define Z3_SERIAL_RX_PIN _EPIN(Z3_E_INDEX, SERIAL_RX) #endif #endif #if defined(Z3_STALL_SENSITIVITY) && ENABLED(Z_MULTI_ENDSTOPS) && NUM_Z_STEPPER_DRIVERS >= 3 && _PEXI(Z3_E_INDEX, DIAG) #define Z3_DIAG_PIN _EPIN(Z3_E_INDEX, DIAG) #if DIAG_REMAPPED(Z3, X_MIN) #define Z3_USE_ENDSTOP _XMIN_ #elif DIAG_REMAPPED(Z3, Y_MIN) #define Z3_USE_ENDSTOP _YMIN_ #elif DIAG_REMAPPED(Z3, Z_MIN) #define Z3_USE_ENDSTOP _ZMIN_ #elif DIAG_REMAPPED(Z3, X_MAX) #define Z3_USE_ENDSTOP _XMAX_ #elif DIAG_REMAPPED(Z3, Y_MAX) #define Z3_USE_ENDSTOP _YMAX_ #elif DIAG_REMAPPED(Z3, Z_MAX) #define Z3_USE_ENDSTOP _ZMAX_ #else #define _Z3_USE_ENDSTOP(P) _E##P##_DIAG_ #define Z3_USE_ENDSTOP _Z3_USE_ENDSTOP(Z3_E_INDEX) #endif #undef Z3_DIAG_PIN #endif #define Z4_E_INDEX INCREMENT(Z3_E_INDEX)#endif
#ifndef Z3_CS_PIN #define Z3_CS_PIN -1#endif#ifndef Z3_MS1_PIN #define Z3_MS1_PIN -1#endif#ifndef Z3_MS2_PIN #define Z3_MS2_PIN -1#endif#ifndef Z3_MS3_PIN #define Z3_MS3_PIN -1#endif
#if NUM_Z_STEPPER_DRIVERS >= 4 #ifndef Z4_STEP_PIN #define Z4_STEP_PIN _EPIN(Z4_E_INDEX, STEP) #define Z4_DIR_PIN _EPIN(Z4_E_INDEX, DIR) #define Z4_ENABLE_PIN _EPIN(Z4_E_INDEX, ENABLE) #if Z4_E_INDEX >= MAX_EXTRUDERS || !PIN_EXISTS(Z4_STEP) #error "No E stepper plug left for Z4!" #endif #endif #if AXIS_HAS_SPI(Z4) #ifndef Z4_CS_PIN #define Z4_CS_PIN _EPIN(Z4_E_INDEX, CS) #endif #endif #ifndef Z4_MS1_PIN #define Z4_MS1_PIN _EPIN(Z4_E_INDEX, MS1) #endif #ifndef Z4_MS2_PIN #define Z4_MS2_PIN _EPIN(Z4_E_INDEX, MS2) #endif #ifndef Z4_MS3_PIN #define Z4_MS3_PIN _EPIN(Z4_E_INDEX, MS3) #endif #if AXIS_HAS_UART(Z4) #ifndef Z4_SERIAL_TX_PIN #define Z4_SERIAL_TX_PIN _EPIN(Z4_E_INDEX, SERIAL_TX) #endif #ifndef Z4_SERIAL_RX_PIN #define Z4_SERIAL_RX_PIN _EPIN(Z4_E_INDEX, SERIAL_RX) #endif #endif #if defined(Z4_STALL_SENSITIVITY) && ENABLED(Z_MULTI_ENDSTOPS) && NUM_Z_STEPPER_DRIVERS >= 4 && _PEXI(Z4_E_INDEX, DIAG) #define Z4_DIAG_PIN _EPIN(Z4_E_INDEX, DIAG) #if DIAG_REMAPPED(Z4, X_MIN) #define Z4_USE_ENDSTOP _XMIN_ #elif DIAG_REMAPPED(Z4, Y_MIN) #define Z4_USE_ENDSTOP _YMIN_ #elif DIAG_REMAPPED(Z4, Z_MIN) #define Z4_USE_ENDSTOP _ZMIN_ #elif DIAG_REMAPPED(Z4, X_MAX) #define Z4_USE_ENDSTOP _XMAX_ #elif DIAG_REMAPPED(Z4, Y_MAX) #define Z4_USE_ENDSTOP _YMAX_ #elif DIAG_REMAPPED(Z4, Z_MAX) #define Z4_USE_ENDSTOP _ZMAX_ #else #define _Z4_USE_ENDSTOP(P) _E##P##_DIAG_ #define Z4_USE_ENDSTOP _Z4_USE_ENDSTOP(Z4_E_INDEX) #endif #undef Z4_DIAG_PIN #endif#endif
#ifndef Z4_CS_PIN #define Z4_CS_PIN -1#endif#ifndef Z4_MS1_PIN #define Z4_MS1_PIN -1#endif#ifndef Z4_MS2_PIN #define Z4_MS2_PIN -1#endif#ifndef Z4_MS3_PIN #define Z4_MS3_PIN -1#endif
#if HAS_MARLINUI_U8GLIB #if !defined(ST7920_DELAY_1) && defined(BOARD_ST7920_DELAY_1) #define ST7920_DELAY_1 BOARD_ST7920_DELAY_1 #endif #if !defined(ST7920_DELAY_2) && defined(BOARD_ST7920_DELAY_2) #define ST7920_DELAY_2 BOARD_ST7920_DELAY_2 #endif #if !defined(ST7920_DELAY_3) && defined(BOARD_ST7920_DELAY_3) #define ST7920_DELAY_3 BOARD_ST7920_DELAY_3 #endif#else #undef ST7920_DELAY_1 #undef ST7920_DELAY_2 #undef ST7920_DELAY_3#endif
#undef HAS_FREE_AUX2_PINS#undef DIAG_REMAPPED
3DFans [Ben]
Dec 10, 2020, 5:11:08 PM12/10/20
to DYZE DESIGN, benva...@gmail.com
It continues. Printing is possible, but as you can see, temperatures fluctuate around + - 12 ° C during printing. PGD was done, but hardly possible as it shoots out over the target. Should I attach my config?
Patrick Emerick
Dec 10, 2020, 7:03:46 PM12/10/20
to DYZE DESIGN, benva...@gmail.com
I don't have any experience with your particular printer or the control board you are using, so I can't really help with specifics on that, but it sounds like your temperature fluctuation is coming from an improper PID tuning process.
1) Your thermistor should read close to room temperature say +/-5C if you temperature table is correct and you haven't heated your nozzle recently.
2) You should be tuning close to the temperature you'll print at, so 50C is far too low. I typically tune for 250C because I print between 220C and 300C depending on the material I'm running.
Check out the Marlin docs: https://marlinfw.org/docs/gcode/M303.html and definitely check out the Dyze Manual: https://docs.dyzedesign.com/hotends.html#pid-tuning-and-adjustments because it mentions PID tuning temperature.
Stick with it because the Dyze Extruder/Hotend is awesome once you get it working!
3DFans [Ben]
Dec 11, 2020, 2:27:46 AM12/11/20
to DYZE DESIGN, benva...@gmail.com
I know the instructions, but the problem is that the documentation is very old and these values no longer exist in the current version. Meanwhile Marlin 2.7.x is out and the documentary is still about Marlin 1.x.x;) Then I'll try my luck on my own. It's a shame that you can't find the fault, because it works with other cheap products without any problems. ;)
Patrick Emerick
Dec 11, 2020, 7:00:28 AM12/11/20
to DYZE DESIGN, benva...@gmail.com
I don't think your problem has anything to do with the Marlin version. I'm not affiliated with Dyze Design, I was just trying to help because it doesn't sound like your problem is specifically related to a Dyze product.
1) Run M303 C8 S250 Utrue
2) If that command fails reduce the PID_MAX variable in the Marlin config until M303 succeeds - I set mine to 204 which limits power to 80% of maximum
3) Once M303 succeeds set a hotend temperature close to what you'll be printing at - The 50C you mentioned earlier may oscillate regardless of how good your PID tune is when using a 60W heater at such a low temperature
Philippe Carrier
Dec 11, 2020, 8:39:24 AM12/11/20
to DYZE DESIGN, Patrick Emerick, benva...@gmail.com
Thanks Patrick for your help.
Also, if you still have problems with the initial heating, make sure you set the E0 Mintemp to a value closer to 10°C. The 500°C thermistor needed a mintemp at 21°C due to poor resolution and limitation, but the 300°C can go much below that. Remember that if the temperature you read is lower than the mintemps, the heaters are turned off automatically.
3DFans [Ben]
Dec 12, 2020, 11:51:42 AM12/12/20
to DYZE DESIGN, pemer...@gmail.com, benva...@gmail.com
Hey, first of all thanks for your help, but that doesn't seem to work either. In any case, he already prints and does the PID tuning, but that doesn't do me much good.
During printing, it goes from the set 235 ° C up to 250 ° C and then down again and of course the results do not look particularly good. Do you have any ideas where to look in Marlin?
Philippe Carrier
Dec 14, 2020, 7:45:05 AM12/14/20
to DYZE DESIGN, benva...@gmail.com, Patrick Emerick
Can you show us a print screen of your temperature graph?
Sometimes, a connector / wire problem can be the source of temperature stability.
A bad PID will move the temperature off slowly (looking like a flat sin wave) while a bad connection will generally have spikes and abrupt changes.
3DFans [Ben]
Dec 16, 2020, 6:15:37 AM12/16/20
to DYZE DESIGN, benva...@gmail.com, pemer...@gmail.com
I have implemented all the tips from above, but unfortunately still the problem that it slowly controls the temperature, but then goes at least 20 ° C too high.
Screenshot: https://ibb.co/HBGd75R
Regards
Philippe Carrier
Dec 16, 2020, 9:20:17 AM12/16/20
to DYZE DESIGN, benva...@gmail.com, Patrick Emerick
Thanks for sharing this picture.
You can see the temperature overshoot is caused by a lag in the heater output (shown in green) and the temperature rise.
With a proper PID tuning, you'll see a flat power usage (green).
Please try making a new PID tuning. I usually use: "M303 S200 C5"
Once it is done, note the ki, kd, and kp values, and make sure they are written to your EEPROM. If they aren't, the values will be reset on each machine startup. You can either activate the EEPROM, or add the PID settings gcode to your start Gcode.
3DFans [Ben]
Dec 16, 2020, 10:12:01 AM12/16/20
to DYZE DESIGN, benva...@gmail.com, pemer...@gmail.com
Hey
I've tried PID tuning several times, but always with different results. Of course I saved the values with M500 after each PID. I have access to Marlin and EPROM through the SKR E3 Turbo. So I don't understand why the temperatures fluctuate so much. I can link a Configuration.h and configuration_adh. Maybe I'm missing something? Thank you for your help.
Patrick Emerick
Dec 16, 2020, 11:52:58 AM12/16/20
to DYZE DESIGN, benva...@gmail.com, Patrick Emerick
I checked my hotend temperature this morning - When temperature is set, full power is applied until the set point is reached, then the power is dropped to a low value and temperature stabilizes, but power never drops to zero like yours does. At that point if no filament is flowing the power value fluctuates by 1 or 2 to maintain the set point temperature. I develop electronics and control systems as my normal job and that picture looks like a poorly tuned PID.
NOTE: Unless you run M303 with the Utrue parameter, the PID values won't even be stored to memory, so M500 won't do anything for you. If you want to view the results of M303 before saving PID values to memory, make sure you save PID values using M301. If you run M301 without any parameters, it should provide you with the PID values that are currently loaded in memory.
3DFans [Ben]
Dec 16, 2020, 12:06:14 PM12/16/20
to DYZE DESIGN, benva...@gmail.com, pemer...@gmail.com
It should go without saying that after the PID the values are entered with M301 and then saved with M500. ;) For me it is also more about that when I set 230 ° C, it then goes up to 250 ° C and then slowly down to 230 ° C. My other printers don't do that. So I assume that at some point in Marlin is wrong.
Frederic Boulianne
Dec 16, 2020, 3:48:41 PM12/16/20
to DYZE DESIGN, benva...@gmail.com, pemer...@gmail.com
Hello Ben
Mine also does that with the steel block but less of an overshoot with the alu block
the pid won't really help with that since the pid are mostly the ability to keep the temp in check after the initial heating
the steel block has a lot more heat mass so the temp variation is slower, as such, it tends to overshoot more on the initial heating
Fred
Reply all
Reply to author
Forward
0 new messages