The kit's got a couple of spray guns in it - one gravity feed, one suction.
Both guns look alright, the suction gun being identical to a primer gun I
picked up for £15 a while back, but to use either properly you really need a
small gun reg and gauge, particularly with a small compressor due to the
small reciever and lack of excess capacity. There's an airbrush, but it's
only useable with water or oil based paints, so it's fairly useless for car
work. There's a load of air hose chucked in for free, which is nice, and
everything is fitted with high flow connectors, which would be a few quid if
you bought them seperately. Neither gun looks to be HVLP.
The other bits and bobs are a tyre inflator, a blow duster, a parafin gun
and a jet washer gun. Basically the stuff you get in any cheap kit of air
tools from any tool shop.
All in all it's bloody cheap for what it is - I reckon you'd be looking at
near on £150 at machine mart for the same sort of clobber. It'd probably be
sufficient for spraying a panel or two, perhaps even a bodyside, but you'd
probably struggle for air with an entire car to do, and would almost
certainly be exceeding the stated duty cycle. Obviously there's the usual
caveat about 2 pack - yes, you could spray it with this kit but you'd need
another compressor outside to run an air fed mask, if you don't want to be
very ill or die.
The compressor is made (or more likely imported by) Omega Wolf, who own the
Wolf Air brand. This appears to be their version of the same kit, minus a
couple of the extra bits and bobs:
http://www.wolf-online.co.uk/product.asp?id=001619
> The other bits and bobs are a tyre inflator, a blow duster, a parafin
> gun and a jet washer gun.
Out of interest, how's that last one work with an air compressor?
You connect up a hose, put the tap on full and the air pressure blasts the
water out. Even without any pressure pushing the spray medium into the gun,
you can wash things down with thinners with a normal spray gun if you set up
a tight pattern.
Sounds handy. And by using a long airline, I guess the compressor could
be kept right out of the way too.
<adds one to shopping list>
> Even without any pressure pushing the spray medium into
> the gun, you can wash things down with thinners with a normal spray gun
> if you set up a tight pattern.
Yup, BTDT.
Its the same motor/compressor as mine bought years ago. Slightly different
paint.
Its been "adjusted" up to 150 psi, and runs at times all day long doing all
kinds of stuff. So far its pretty unbreakable so I wouldnt worry!
Its a "proper" well built oil in sump (synthetic in my case!) compressor
with crank and piston/rings etc but instead of driving by belt its turned
to face the motor and is direct drive. And the motor is a powerful induction
motor so nothing to wear.
The only problem was the crappy diy connectors. Easily swapped and adapted
Now its got one or two of every connector!
www.cordeaux.net/comp1.JPG
www.cordeaux.net/comp2.JPG
--
DIY Nitrous www.nitrous.info
Powerchairs www.powerchair-review.co.uk
Disabled vehicle conversion www.wheelchairdriver.com
Engines www.more-power.info
Any good for spraying fencing panels with Cuprinol or whatever, do you
reckon? I've got about 20 to do this summer :o(
John
Fine as long as you're willing to wait for it to fill the reciever.
Atomisation won't really be important so you should be able to drop the air
pressure down (probably below the recommended minimum of 40psi, say 20 or
30) open the needle right up and lather it on. That way you'll minimise
overspray - even with a really good efficient spraygun, 70% of the paint you
shoot at a car doesn't end up on it.
I've not got it out yet as it's in the house rather than the workshop. Does
it have a basic regulator fitted to the tin outputs?
Ah, cheers mate. I might just treat myself to a new toy then :o)
John
> www.cordeaux.net/comp1.JPG
> www.cordeaux.net/comp2.JPG
<topic wandering>
Ooh, a D300. Nice.
--
Douglas
"Douglas Payne" <dou...@cheerful.com> wrote in message
news:62o15tF...@mid.individual.net...
Marvelous for photographing dusty dusty old compressors in dingy dark
workshops!
Seriously recommended for everything else though...
See I get priorities right! Cheapest compressor possible but almost the
dearest camera...
One fopr all outputs
There is (was?) a proper reg/lube with 10m and 3m hose for £19.99.
I seem to have a full boot.
--
Peter Hill
Spamtrap reply domain as per NNTP-Posting-Host in header
Can of worms - what every fisherman wants.
Can of worms - what every PC owner gets!
> There is (was?) a proper reg/lube with 10m and 3m hose for £19.99.
>
> I seem to have a full boot.
The reg is identical to a sealey one I have already. I expect the oiler will
be similarly identical to the Sealey equiv. Just been and got one as I'm fed
up of air tools needing a bit of 3 in 1 in whenever I pick them up...