PTFE covered wire - how to strip off the PTFE?
N_Cook
insulation. The outer strips off easily with any old wire stripper, but
however new , gap limited cutters , will not cut the underlying PTFE.
Outer is double spiral wound PTFE sheet/ribbon I think, heated to lock
together to a certain extent. The inner is more fibrous in nature. Cutting
the remaining inner material , even difficult with a razor. The only
technique I've found, is remove the outer as normal , then .5mm grinding
disc in a Dremmel , only just touching, run all around and then pull off,
rarely cuts a wire strand . Other than some mega-buck NASA/Mil approved
cutter any other ideas?
Smitty Two
"N_Cook" <div...@tcp.co.uk> wrote:
The type of stripper shown here:
<http://rocky.digikey.com/weblib/OK%20International/Web%20Photo/ST-500.jp
g>
is pretty good with teflon. Sold under various brand names, and also in
different adjustable gauge ranges or in fixed sizes.
For teflon, squeeze fully to cut through insulation, then back off very
slightly to pull off slug.
Jeff Liebermann
wrote:
Thermal wire stripper (STRIPALL)
<http://www.teledyneinterconnect.com/products/stripall/default.asp>
<http://shop.ebay.com/i.html?_nkw=thermal+wire+stripper>
I have several sets of these and use them on anything that might be
damaged by a blade. Make sure you get some spare blades.
--
Jeff Liebermann je...@cruzio.com
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558
Dave Platt
I've had reasonably good luck on PFTE wire and cable (including the
spiral-fused-tape-insulated type) using a set of "hot tweezer" wire
strippers. Bought 'em used through a dealer in such things who has a
table at a local hamfest every month.
The temperature of the heated stripping element can be adjusted...
anywhere from a gentle warmth which melts through PVC without making
it smoke, up to a literally red-hot glow which will cut through PFTE
down to the underlying wire.
[Using a fume evacuator, or at least a small fan, is a good idea in this
case, to avoid the risk of inhaling the fumes... a nasty respiratory
syndrome can result. Don't do this at all if you keep pet birds
around... they're acutely sensitive to the fumes from overheated
Teflon and etc.]
--
Dave Platt <dpl...@radagast.org> AE6EO
Friends of Jade Warrior home page: http://www.radagast.org/jade-warrior
I do _not_ wish to receive unsolicited commercial email, and I will
boycott any company which has the gall to send me such ads!
Jeffrey Angus
> [Using a fume evacuator, or at least a small fan, is a good idea in this
> case, to avoid the risk of inhaling the fumes... a nasty respiratory
> syndrome can result. Don't do this at all if you keep pet birds
> around... they're acutely sensitive to the fumes from overheated
> Teflon and etc.]
And nerve damage...
Both nasty side effects.
Good ventilation is a must.
Jeff
N_Cook
news:prestwhich-16DC1...@news.eternal-september.org...
Thats the type I use.
I think I'll make my own cutter, a pair of razor blades set with a tapered
gap between cutting edges (gap a bit larger than ext diam down to wire
diam). Push the wire down the gap in 2 orthogonal directions and then rotate
round at the narrow end. Then sleeve should slide off easily as its the
cutting completely around that is the problem. I'd rather avoid melting of
PTFE (the fluoro bit) especially as it cuts so easily.
Hopefully something like a minimal version of these PTFE specific cutters,
I only have one drum of one size of this wire, so no adjuster needed
http://int.rsdelivers.com/product/rs/o6804/ptfe-wire-stripper-091-45mmdia-cu
tting/0608301.aspx
http://docs-europe.electrocomponents.com/webdocs/001b/0900766b8001b254.pdf
N_Cook
filaments.
Two 2inch lengths of 12mm diameter hotmelt sticks. Temp controlled solder
iron , melt a slot axially in one. With a pair of razor blades gripped in an
engineer's cramp with gap one end , wider than the outer PTFE, and the other
with blade edges touching at a point. Push the wide gap end into the
hotmelt. Cool and repeat with the other end. Mark along the razor edge where
the stripped wire falls to.
Push some of the sleeved wire down to just beyond this point and drop
hotmelt , filling the space down to the closed gap end.
One sliding cut and 180 degree rotation is all that is needed , slide away,
remove from the slot and pull off the cut sleeving.
Smitty Two
"N_Cook" <div...@tcp.co.uk> wrote:
Glad your home-made gadget worked, but the cutters I referenced are the
ones we use every day for stripping teflon. I'm surprised they wouldn't
do it for you. It does take a bit of technique as noted, setting depth
to cut fully through, then backing off pressure to remove slug. The 90
degree rotate and 2nd cut helps, but for production work is too slow.
N_Cook
This wire is very fine filament multistrand. perhaps 30 wire strands. If it
was solid conductor it would be easier to strip. But the main problem is the
multiple thin sleeve layers , perhaps 3, under the thick outer sleeving.
PTFE seems to be strong in one sense and transverse very weak. If the fibrey
part was laid up transversely it would easily part at the cutting point, but
the layup is strong axially.