info
Google Groups no longer supports new Usenet posts or subscriptions. Historical content remains viewable.
Dismiss
Recommendations orExperience with Delta Electronics DPS-310CD?
36 views
Skip to first unread message
KenO
Feb 15, 2018, 2:54:32 PM2/15/18
to
Hi,
Recently my IBM/Lenovo ThinkCentre(Tower) would not turn on. There was no indication of failure on last run.
Did some power supply problem searching and one thing mentioned was a blown fuse.
Took the cover off and checked for leaking or bulging caps but found none.
Also checked for std fuse but also found none. Am wondering if it may have a fusible link?
Also searched for the schematics for the DPS-310CD but to date have not found any.
Appreciate any help!
Thanks
Ken
Recently my IBM/Lenovo ThinkCentre(Tower) would not turn on. There was no indication of failure on last run.
Did some power supply problem searching and one thing mentioned was a blown fuse.
Took the cover off and checked for leaking or bulging caps but found none.
Also checked for std fuse but also found none. Am wondering if it may have a fusible link?
Also searched for the schematics for the DPS-310CD but to date have not found any.
Appreciate any help!
Thanks
Ken
et...@whidbey.com
Feb 16, 2018, 12:31:25 PM2/16/18
to
On Thu, 15 Feb 2018 11:54:27 -0800 (PST), KenO <kenit...@yahoo.com>
wrote:
Recently I had a power supply in a computer that was going bad. It
wouldn't work properly until it was warm. I replaced it but before I
did I found that directing the warm air from a blow dryer through the
fan and warming the power supply would allow it to turn on. Once on it
would stay on. The hair dryer was a good way to determine that it was
the power supply and not the computer itself that was the problem.
Advice from the folks on the group helped too.
Eric
wrote:
wouldn't work properly until it was warm. I replaced it but before I
did I found that directing the warm air from a blow dryer through the
fan and warming the power supply would allow it to turn on. Once on it
would stay on. The hair dryer was a good way to determine that it was
the power supply and not the computer itself that was the problem.
Advice from the folks on the group helped too.
Eric
Ralph Mowery
Feb 16, 2018, 12:43:33 PM2/16/18
to
In article <g85e8dpepd11b6t68...@4ax.com>,
et...@whidbey.com says...
I had a piece of equipment with a power supply that had lots of
capacitors in it. I found the bad ones by directing the hot air from my
hot air rework station at them. I may have replaced some that were ok,
but they are inexpensive compaired to a new supply. Actually can not
get a new one, but a company repaires them for about $ 150.
et...@whidbey.com says...
>
> Recently I had a power supply in a computer that was going bad. It
> wouldn't work properly until it was warm. I replaced it but before I
> did I found that directing the warm air from a blow dryer through the
> fan and warming the power supply would allow it to turn on. Once on it
> would stay on. The hair dryer was a good way to determine that it was
> the power supply and not the computer itself that was the problem.
> Advice from the folks on the group helped too.
> Eric
>
>
Probably some bad capacitors in the supply.
> Recently I had a power supply in a computer that was going bad. It
> wouldn't work properly until it was warm. I replaced it but before I
> did I found that directing the warm air from a blow dryer through the
> fan and warming the power supply would allow it to turn on. Once on it
> would stay on. The hair dryer was a good way to determine that it was
> the power supply and not the computer itself that was the problem.
> Advice from the folks on the group helped too.
> Eric
>
>
I had a piece of equipment with a power supply that had lots of
capacitors in it. I found the bad ones by directing the hot air from my
hot air rework station at them. I may have replaced some that were ok,
but they are inexpensive compaired to a new supply. Actually can not
get a new one, but a company repaires them for about $ 150.
KenO
Feb 17, 2018, 12:09:34 PM2/17/18
to
Hi
Update since posting.
Did not get an immediate response so went to Youtube and searched using diagnosis repair Delta Electronics DPS-310CD ATX power supplies got ~ 197 results. Then started watching the videos.
One thing mentioned was to wait a while for caps to discharge so decided to take plenty of time and waited until this morning to test.
First thing I did was to recheck all the caps for bulges or leaks. Found none. Also rechecked for burn marks on pc board and components. Also found none. Still was unable to identify anything that looked like a fuse. Would be nice to find a schematic for DPS-310CD. Have done some searching but to date have not found one.
Then decided to try starting. Followed the connect green and black wires of main power connector http://www.instructables.com/id/Take-a-Look-Inside-a-ATX-power-supply-for-computer/ to start and was surprised that green lite on PSU came on and got readings of 11.89V for yellow and black, and 5.15V for red and black wires of a parallel HDD connector.
Am wondering if 11.89V for HDDs is too low? I do not have a scope to check the wave form but the readings were stable on my meter.
Update since posting.
Did not get an immediate response so went to Youtube and searched using diagnosis repair Delta Electronics DPS-310CD ATX power supplies got ~ 197 results. Then started watching the videos.
One thing mentioned was to wait a while for caps to discharge so decided to take plenty of time and waited until this morning to test.
First thing I did was to recheck all the caps for bulges or leaks. Found none. Also rechecked for burn marks on pc board and components. Also found none. Still was unable to identify anything that looked like a fuse. Would be nice to find a schematic for DPS-310CD. Have done some searching but to date have not found one.
Then decided to try starting. Followed the connect green and black wires of main power connector http://www.instructables.com/id/Take-a-Look-Inside-a-ATX-power-supply-for-computer/ to start and was surprised that green lite on PSU came on and got readings of 11.89V for yellow and black, and 5.15V for red and black wires of a parallel HDD connector.
Am wondering if 11.89V for HDDs is too low? I do not have a scope to check the wave form but the readings were stable on my meter.
KenO
Feb 17, 2018, 12:13:04 PM2/17/18
to
Update cont.
Forgot to mention the Fan came on when started..
Forgot to mention the Fan came on when started..
KenO
Feb 17, 2018, 12:15:07 PM2/17/18
to
Eric,
"Recently I had a power supply in a computer that was going bad. It
wouldn't work properly until it was warm. I replaced it but before I
did I found that directing the warm air from a blow dryer through the
fan and warming the power supply would allow it to turn on. Once on it
would stay on."
Any ideas why it needed to be warm?
"Recently I had a power supply in a computer that was going bad. It
wouldn't work properly until it was warm. I replaced it but before I
did I found that directing the warm air from a blow dryer through the
fan and warming the power supply would allow it to turn on. Once on it
would stay on."
KenO
Feb 17, 2018, 12:19:33 PM2/17/18
to
Ralph,
"I had a piece of equipment with a power supply that had lots of
capacitors in it. I found the bad ones by directing the hot air from my
hot air rework station at them."
That was what I was expecting to find!
"I had a piece of equipment with a power supply that had lots of
capacitors in it. I found the bad ones by directing the hot air from my
hot air rework station at them."
et...@whidbey.com
Feb 17, 2018, 1:47:57 PM2/17/18
to
On Sat, 17 Feb 2018 09:15:02 -0800 (PST), KenO <kenit...@yahoo.com>
wrote:
I was told by some folks here who know about this stuff that failing
electrolytic capacitors will sometimes work better once warm. They do
not need to be bulging to be bad or going bad.
Eric
wrote:
electrolytic capacitors will sometimes work better once warm. They do
not need to be bulging to be bad or going bad.
Eric
Ralph Mowery
Feb 17, 2018, 4:51:34 PM2/17/18
to
In article <f22ea9c5-13ac-4e5c...@googlegroups.com>,
kenit...@yahoo.com says...
11.89 is fine for the 12 volt line.
kenit...@yahoo.com says...
0 new messages