Google Groups no longer supports new Usenet posts or subscriptions. Historical content remains viewable.
Dismiss

liquid electric tape?

106 views
Skip to first unread message

Jezebels_couz

unread,
Dec 6, 2020, 1:49:13 PM12/6/20
to
Anyone here use it and what is its durability? How about melting
temperature in warmer environments? Thanks.

Paul Drahn

unread,
Dec 6, 2020, 1:57:39 PM12/6/20
to
On 12/6/2020 10:49 AM, Jezebels_couz wrote:
> Anyone here use it and what is its durability?  How about melting
> temperature in warmer environments?  Thanks.
I have used it on connections between coax and antennas. Never had a
problem. Regular PVC black electrical tape either splits or looses it's
sticky after two years due to the UV here in the Central Oregon desert.

Liquid tape in bottles turns solid after about two years.

Paul

Jeff Liebermann

unread,
Dec 6, 2020, 2:05:08 PM12/6/20
to
On Sun, 6 Dec 2020 13:49:08 -0500, Jezebels_couz <jb...@three.net>
wrote:

>Anyone here use it and what is its durability? How about melting
>temperature in warmer environments? Thanks.

I bought a can of this stuff at the local hardware store:
<https://www.amazon.com/Star-brite-Liquid-Electrical-Tape/dp/B0000AXNOD>
My first use was to patch cracks and cuts in several expensive rubber
cables. It went on fairly easily but hardened a bit lumpy. It lasted
about a month before pieces started falling off. There might have
been some contamination (grease, hand oils, solvents) involved, but it
was too late to check. I later used it for rubber microphone coil
cords, which also crumbled after a few weeks of movement. This time,
I gave the cable an acetone wipe, which should have removed any
grease.

However, the lack of durability was not the major problem. It was the
can. No matter how hard I tried, I could not keep the rubber compound
from getting into the threads on the lid. Once the stuff hardened, it
was impossible to remove the lid. I tried various straps, clamps,
pliers, pipe wrenches, and solvents. Nothing would get the lid loose.
After losing the contents of 2 cans in this manner, I gave up and
decided to find something else.

No clue on melting temperature.

--
Jeff Liebermann je...@cruzio.com
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558

amdx

unread,
Dec 7, 2020, 7:51:24 AM12/7/20
to
On 12/6/2020 12:49 PM, Jezebels_couz wrote:
> Anyone here use it and what is its durability?  How about melting
> temperature in warmer environments?  Thanks.

 I used liquid Tape to repair a large nick in the insulation of a heavy
duty extension cord over 25 years ago.

 The cord is still great (but very heavy) the repair is fine and I
never thought about it melting, but I'm in Florida and I never noticed
it soften.

Wish I could till you the brand and if they still make it the same way.


                                    Mikek


--
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus

Stephen Wolstenholme

unread,
Dec 7, 2020, 8:49:02 AM12/7/20
to
On Sun, 6 Dec 2020 13:49:08 -0500, Jezebels_couz <jb...@three.net>
wrote:

>Anyone here use it and what is its durability? How about melting
>temperature in warmer environments? Thanks.

I used some liquid electric tape about five year ago. It was to
insulate a joint in a cable supplying the pump in a waterfall. It is a
few inches under a lawn. It gets frozen in winter and baked in summer.
I think it is Loctite brand.

Steve

--
http://www.npsnn.com

Rob

unread,
Dec 7, 2020, 10:02:43 AM12/7/20
to
Jezebels_couz <jb...@three.net> wrote:
> Anyone here use it and what is its durability? How about melting
> temperature in warmer environments? Thanks.

Unless you have some special requirement I would advice self-amalgamating
tape instead.

Tom Kupp

unread,
Dec 9, 2020, 5:43:00 PM12/9/20
to
On 12/06/20 13:49, Jezebels_couz wrote:
> Anyone here use it and what is its durability?  How about melting
> temperature in warmer environments?  Thanks.
Check Glyptal.

bruce bowser

unread,
Dec 10, 2020, 3:37:38 PM12/10/20
to
On Sunday, December 6, 2020 at 2:05:08 PM UTC-5, Jeff Liebermann wrote:
> On Sun, 6 Dec 2020 13:49:08 -0500, Jezebels_couz <jb...@three.net>
> wrote:
> >Anyone here use it and what is its durability? How about melting
> >temperature in warmer environments? Thanks.
> I bought a can of this stuff at the local hardware store:
> <https://www.amazon.com/Star-brite-Liquid-Electrical-Tape/dp/B0000AXNOD>
> My first use was to patch cracks and cuts in several expensive rubber
> cables. It went on fairly easily but hardened a bit lumpy. It lasted
> about a month before pieces started falling off. There might have
> been some contamination (grease, hand oils, solvents) involved, but it
> was too late to check. I later used it for rubber microphone coil
> cords, which also crumbled after a few weeks of movement. This time,
> I gave the cable an acetone wipe, which should have removed any
> grease.
>
> However, the lack of durability was not the major problem. It was the
> can. No matter how hard I tried, I could not keep the rubber compound
> from getting into the threads on the lid. Once the stuff hardened, it
> was impossible to remove the lid. I tried various straps, clamps,
> pliers, pipe wrenches, and solvents. Nothing would get the lid loose.

I'm a regular with liquid nails when wiring up construction sites and I know the feeling trying to recover goop, sparkle, other tube/can/bottle contents. I guess ultimately two channel locks going in opposite directions might crush or damage the bottle if wet rags don't cushion the jaws. I've seen where you could use a belt to unscrew an oil filter near a car's engine for an oil change.

FromTheRafters

unread,
Feb 1, 2021, 12:57:40 AM2/1/21
to
Jeff Liebermann used his or her keyboard to write :

> It lasted
> about a month before pieces started falling off.

My experience is similar.

Three Jeeps

unread,
Feb 3, 2021, 12:20:50 AM2/3/21
to
On Sunday, December 6, 2020 at 1:49:13 PM UTC-5, Jezebels_couz wrote:
> Anyone here use it and what is its durability? How about melting
> temperature in warmer environments? Thanks.
I tried it once. Was not impressed, seemed to crack off after a while.
What I have used that I really like is rubber electrical tape. Ethylene propylene and silicone rubber electrical tapes have the highest dielectric rating of electrical tapes, as much at 70KV. I use 3M 2228.
I learned about this stuff during my first engineering job in a blast furnace construction site. the controls I designed interfaced to some beefy motors. One of the electricians that followed me around was tasked to replace one of the motors because it was not what I specified. As I watched him wire the new motor, he used that rubber electrical tape. Neat stuff-the overlapping wraps fuse together to make a rubber jacket. Long lasting in hot and cold environments. Follow up with a few wraps of good electrical tape - I like 3M 88 or for everyday use, super 33.
Good luck
J

Jeff Liebermann

unread,
Feb 3, 2021, 1:42:18 PM2/3/21
to
It costs about $1/ft:
<https://www.homedepot.com/p/3M-Scotch-1-in-x-10-ft-x-0-065-in-2228-Rubber-Mastic-Electrical-Tape-Black-50727-BA-5/202195402>
I've used it on radio towers and found a problem. The self-fusing
glue is so tenacious, that removing it from a connector is almost
impossible. For situations where you're certain it never needs to be
removed, it's great and quite waterproof. For RF connectors that need
to be removed, I use 1" wide PTFE (Teflon) tape for waterproofing,
covered with 1 or 2 layers of Scotch 66 to hold it in place. When the
tape wrap is removed, the connectors look like new.


--
Jeff Liebermann je...@cruzio.com
PO Box 272 http://www.LearnByDestroying.com
Ben Lomond CA 95005-0272
Skype: JeffLiebermann AE6KS 831-336-2558

tschw...@aol.com

unread,
Feb 3, 2021, 8:33:14 PM2/3/21
to
There is a product called Sugru, it's not liquid but rather a very resilient rubber putty. Cures in a few hours, It's mold-able and comes in several colors. I've used it to repair things and reinforce cords where they exit devices. Handy stuff.

three_jeeps

unread,
Feb 10, 2021, 1:03:36 PM2/10/21
to
Yes, good point - it is rather tenacious. If the connection needs to be reworked in the future, it is a little tough to remove it. I've tried teflon tape on occasion and found that it slides and shifts around so much that it is hard to get a clean wrap so to speak. One good thing is that teflon tape has a very high dielectric strength, something like 6kv at 0.001 inch thick, (or is it 0.001? i forget). It would do quite well in RF applications.
J

Peter W.

unread,
Feb 12, 2021, 7:54:09 AM2/12/21
to
Late on this, but there is a material called Bond-Tech GS 112 rated for electronics and cables. It is also food-safe and stable (solid) to 85C +/- 5C. This stuff is NOT meant to be re-worked, nor would I think that any liquid-applied material would work well that way. It would have to dry out in a way that does not adhere to the substrate to be easily removable. Which seems contrary to the intent, unless very temporary.

Just a thought.

Peter Wieck
Melrose Park, PA

bruce bowser

unread,
Feb 21, 2021, 4:52:06 AM2/21/21
to
What are some foreign equivalents to the jeep or Humvee (HMMWV)?

Peter W.

unread,
Feb 21, 2021, 7:21:14 AM2/21/21
to
G-Wagon
Unimog

Borh by Daimler.

Wolf by Land Rover

Sherpa by Renault

All that I can think of, offhand. There must be more.

Peter Wieck
Melrose Park, PA

bruce bowser

unread,
Feb 25, 2021, 7:23:37 PM2/25/21
to
In WWII, the japanese used something called the type 95 by Tokyu Kurogane Industries and I guess you could remember the Volkswagen Kübelwagen (type 82) from Hogan's Heroes.

Chuck

unread,
Feb 26, 2021, 12:38:53 PM2/26/21
to
The Russian Lada Niva is considered one of the most rugged SUVs.
0 new messages