Sanyo M2820 Portable Radio/Cassette Recorder Schematic Source

[jaugu...@verizon.net]

Hi,

Does anyone know of a site where I can buy a schematic for a Sanyo model
M2820 portable (mono) radio/cassette recorder?

Thank You in advance, John

PS, I searched the Web and tried www.samswebsite.com (Photofacts &
technical publications).

[dansabr...@yahoo.com]

A different approach would be to mention the problem. Perhaps we can suggest a fix without the need for the manual.

Dan

[Dave]

I see there's one listed on ebay - not mine but I should have one according to an old database I have from my service days back then.
I do put some on ebay as I find them depending on condition etc.
I'll keep a look out for it but it could take some weeks to locate.
Dave

[jurb...@gmail.com]

Try your basic Google search. Many times it comes up with a link to electrotanya. There is also a very very slight chance the hifmanuals or hifiengine has it.

[jaugu...@verizon.net]

On Thu, 28 Sep 2017 14:38:47 -0700 (PDT), dansabr...@yahoo.com wrote:

>A different approach would be to mention the problem. Perhaps we can suggest a fix without the need for the manual.
>
>Dan

Hi Dan,

I should have mentioned I am a retired service tech (many years) in consumer
products (TVs, VCRs, Stereos, etc.) repair.

The problem has to do with a long delay 30 to 40 seconds when you turn on
the Radio before you hear the sound. This happens when the radio
has not been turned on for several hours. If you turn on the radio in 15
minutes to a few hours after it was on, the sound "comes on" very quickly.

I know the technique to isolate the faulty stage. The schematic would save
me time (I won't have to circuit trace).

John

[pf...@aol.com]

On Friday, September 29, 2017 at 4:27:32 PM UTC-4, jaugu...@verizon.net wrote:

>
> I know the technique to isolate the faulty stage. The schematic would save
> me time (I won't have to circuit trace).

Agreed. However, I suspect that you will find that electrolytic capacitors in general will be the actual problem(s). Look for any swelling or signs of damage or leakage - you may not need the schematic after all.

Peter Wieck
Melrose Park, PA

[John-Del]

On Friday, September 29, 2017 at 4:27:32 PM UTC-4, jaugu...@verizon.net wrote:

Try preheating the radio. If it then comes on immediately you've almost certainly got a lazy small value electrolytic on the board.

If you have an ESR checker, run through all the caps after the radio has spent about half an hour in the refrigerator.

I still make an excellent living repairing consumer electronics, and using time saving shortcuts allow me to do so. Very few things these days has a full schematic for it. Most of the time I'm piecing them together from IC datasheets.

[Ralph Mowery]

In article <20011a14-9032-446b...@googlegroups.com>,
ohg...@gmail.com says...

>
>
>
>
> Try preheating the radio. If it then comes on immediately you've almost certainly got a lazy small value electrolytic on the board.
>
> If you have an ESR checker, run through all the caps after the radio has spent about half an hour in the refrigerator.
>
> I still make an excellent living repairing consumer electronics, and using time saving shortcuts allow me to do so. Very few things these days has a full schematic for it. Most of the time I'm piecing them together from IC datasheets.

If it has a switching power supply that is where I would look for a bad
capacitor or more. If you have one of the SMD heat guns, play it on the
electrolytic capacitors to see which one makes it come on faster.