What's next after bad caps LG W2252TQ-TF schematic?

[mike]

I picked up a free LG W2252TQ-TF.
lights up for a second then quits.
Figgered bad caps, but I pulled and tested 'em all.
All good. No bulges.

Checked all the diodes. Other semiconductors aren't
shorted. Two fets in the backlight supply probably
have the highest stress level, but I thought I'd
ask for ideas before trying to get them out.

It's gonna be difficult to power it up disassembled.

Ideas on other possible high failure rate parts?
Schematic?

Thanks, mike

[Arfa Daily]

"mike" <ham...@netzero.net> wrote in message
news:kn7c2a$mda$1...@dont-email.me...

Backlight tube itself ? Most of the lamp inverters that I've seen, have
current monitoring. If a 'wrong' current caused by a defective tube is
detected, the inverter just shuts down. It makes them hard to troubleshoot
without an appropriate load. You can check that the supply voltage stays up,
and that the 'on' signal to the inverter stays asserted. I've had a couple
of the high voltage tube coupling caps fail over the years, and also
transformers. You can make sure that the backlight itself has quit, and it's
not just that the screen has gone black, by shining a powerful light at the
front of the screen, at an angle. Usually, you will be able to see at lest
some vestige of what should be being displayed, if it *is* that the
backlight has gone out.

Arfa

[mike]

Good call. One of the backlight secondaries is open.
Thought I'd take a shot at trying to fix it.

Hypothesizing that the connection to the pin might be open, I measured
some capacitances to attempt to determine which end.

The good secondary measures 2.68pF from primary to either end of the
secondary.
The bad secondary measures 2.68pF from primary to one end of the secondary
and 10pF to the other end.

Now, I'm confused. I expected to have the sum of the two measurements
on the open secondary to add up to about 2.68pF.

Another thing I'd never seen before was that each end of the winding has
two turns of what looks like 5 or so wires twisted together headed for the
connector pin. The wire to the pin is potted, so can't see the actual
pin connection.

Can't get my head around how or why they did that???

The winding is in the clear, looks like a single layer, so
if I can find the break, I can probably fix it.

[Arfa Daily]

"mike" <ham...@netzero.net> wrote in message

news:kn8c3k$oce$1...@dont-email.me...

Sod's law of course, says that it will be at the inside of the winding ...
:-\

Failing that, you might be able to cull a suitable transformer from a scrap
board. Quite a few use the same or very similar transformers. It might even
be worth Googling for a replacement, as some of these are available.
Likewise, complete inverter boards for some models, are available at quite
reasonable prices.

i.e.
http://www.shopjimmy.com/lg-eay38280101-power-supply-backlight-inverter.htm

and

http://www.ebay.com/itm/New-replacement-Transformer-for-Samsung-LCD-TMS93137CT-/400219921779

or

http://www.aliexpress.com/store/product/TMS93137CT-Inverter-Transformer-100-New-High-Quality-Free-Shipping/208458_735816735.html

Arfa

[Plai...@yawhoo.com]

Much good advice may be available at www.badcaps.net/forum Be
prepared to provide good quality pictures.

Try www.elektrotanya.com for a service manual.

PlainBill

[mike]

Thanks, guys.
Found the service manual.
Looks like I can get a transformer for $12 or so.
I've got lots of time, so I think I'll take a whack at fixing
the transformer.
Be just my luck to buy a transformer and find other issues.
Never can tell what you're gettin' at a garage sale.

Thanks, mike

[mike]

The plot thickens...

LG W2252TQ-TF
Powers up but no backlight.
has four backlight lamps with two transformer secondaries.
TMS93137CT is the transformer.
One of the secondaries is open. The other one measures about 1.5K.
I zapped it with a stun gun. The open secondary now measures 1.5K also.
But the "fix" didn't survive the reinstallation of the transformer.
It's open again.

So, I ordered a new transformer. Got it today, and the SAME secondary
is open.
Looks new and has the right part number on it. The secondary winding is
definitely
there, just open. Same side as the original. Maybe some manufacturing
defect.

When I opened up the monitor, both my original secondaries measure ~1K,
but after
powering it up, the bad one is open again and no backlight at all.

By now, you're asking, "is there a question in there?"...
nope, just venting.
If anybody has a suggestion, I'm all ears.
Meanwhile contacting the vendor....

Thanks, mike