FS or swap: *huge* metalcutting bandsaw, 40 inch throat, 1700 lbs, in north central florida
dave
model "enco 1000" made in taiwan. 2hp motor, infinitely variable speed,
230 volt three phase, table tilts (all four ways: forward, back, left
and right). has blade WELDER and annealer, too. grinds the blade too, is
my understanding. and an 'air puffer' that blows the chips off your cut
line. it's all there. it's dusty. it needs four new tires, and a general
cleanup. it weighs 1700 lbs
NOT stored at my location, but I *am* the owner. will provide any type
receipt or bill of sale you want. can 'probably' load the thing up for
you (inquire first). no asking price, it must go, I'm not insane though.
prefer to sell outright, but will also 'partial swap' for stuff on my
wants list (or maybe other stuff). might even swap it outright for
something of extreme grooviness.
spec's online, photos online, 'comparable' saw pix with spec's online,
movie of it online, see it in ALL its glory here:
http://machines.netai.net/bandsaw_40_inch_cheap/
e-mail links on site, bottom center of every page
thanks,
dave
Gunner Asch
wrote:
Where are you located?
And your website is "under review"...no pictures are available.
Gunner
"IMHO, some people here give Jeff far more attention than he deserves,
but obviously craves. The most appropriate response, and perhaps the
cruelest, IMO, is to simply killfile and ignore him. An alternative, if
you must, would be to post the same standard reply to his every post,
listing the manifold reasons why he ought to be ignored. Just my $0.02
worth."
ATP*
"Gunner Asch" <gun...@NOSPAMlightspeed.net> wrote in message
news:on8cf59vtvbhf9bmo...@4ax.com...
> On Sat, 07 Nov 2009 17:09:35 -0500, dave <tool...@weirdstuffcox.net>
> wrote:
>
>>bubba bought a biggie. WAY TOO biggie, matter of fact.
>>
>>model "enco 1000" made in taiwan. 2hp motor, infinitely variable speed,
>>230 volt three phase, table tilts (all four ways: forward, back, left
>>and right). has blade WELDER and annealer, too. grinds the blade too, is
>>my understanding. and an 'air puffer' that blows the chips off your cut
>>line. it's all there. it's dusty. it needs four new tires, and a general
>>cleanup. it weighs 1700 lbs
>>
>>NOT stored at my location, but I *am* the owner. will provide any type
>>receipt or bill of sale you want. can 'probably' load the thing up for
>>you (inquire first). no asking price, it must go, I'm not insane though.
>>
>>prefer to sell outright, but will also 'partial swap' for stuff on my
>>wants list (or maybe other stuff). might even swap it outright for
>>something of extreme grooviness.
>>
>>spec's online, photos online, 'comparable' saw pix with spec's online,
>>movie of it online, see it in ALL its glory here:
>>
>>http://machines.netai.net/bandsaw_40_inch_cheap/
>>
>>e-mail links on site, bottom center of every page
>>
>>thanks,
>>
>>dave
>>
> Where are you located?
>
Michael A. Terrell
ATP* wrote:
>
> Gunner Aschwrote:
> >
> > Where are you located?
>
> north central florida
'North Central Florida' covers over 25% of the state but his IP
address resolves to Gainesville. No telling how accurate that is, since
it is assigned to Cox Cable. My IP address shows me about a two hour
drive from where I live.
--
The movie 'Deliverance' isn't a documentary!
dave
> ATP* wrote:
>> Gunner Aschwrote:
>>> Where are you located?
>> north central florida
whoa! I'm in gainesville, however the saw is in alachua florida. site
says so (who would've expected to post a site, test it as working and
answering, *then* have it 'go down' an hour later with that 'under
review' nuisance. brand new host today, 1st site posted there. these
'free site hosts' can be *QUITE* the huge nuisance, and always for some
totally Unexpected reason...
meanwhile, here's an ALTERNATE location: same exact site, on a different
host (also tested working, as of time of this post)
http://machines.2x.nu/bandsaw_40_inch_cheap/
direct e-mail reply links on the bottom of -each- page on the site,
along with links to the bandsaw movie, and other stuff...
sorry, guys, thanks,
dave
Gunner Asch
wrote:
Damn. Sigh
Nice looking saw. Be nice to have in the shop.
Damn........sigh......
Michael A. Terrell
Gunner Asch wrote:
>
> ATP* wrote:
> >
> >north central florida
> >
> Damn. Sigh
>
> Nice looking saw. Be nice to have in the shop.
>
> Damn........sigh......
Yes. It's a little over 60 miles from me, but I'm sure it's not in my
budget. :(
Gunner Asch
<mike.t...@earthlink.net> wrote:
>
>Gunner Asch wrote:
>>
>> ATP* wrote:
>> >
>> >north central florida
>> >
>> Damn. Sigh
>>
>> Nice looking saw. Be nice to have in the shop.
>>
>> Damn........sigh......
>
>
> Yes. It's a little over 60 miles from me, but I'm sure it's not in my
>budget. :(
I wonder if he would donate it and take the credit on his taxes?
dave
bandsaw sale now includes bonus pair of shoes:
(see last three pix)
http://machines.freehostia.com/shoes_3_pair/
ok, thanks :-)
dave