Parting out Quickie Q-200
Sam Hoskins
flying Quickie Q-200 and he asked me to spread the word. Here it is:
The attached list shows items available from parting out my Q-200.
Asking prices are shown for each item. All sales are being made on an
as is where is basis. All items have been removed from the airplane and
are available for shipment. Shipment for all items except the Airframe
components can be made via UPS. Estimated cost for shipment will be
added
to the purchase price Airframe components require the buyer to arrange
for packing and shipment at buyers expense. Payment of purchase price
and
estimated shipment cost will be in USA Curreny, or Certified Check
before
shipment unless other arrangements are agreed to..
If you are interested in any of the items contact me by phone
502-426-0442 or e-mail to ----artj...@juno.com. The airframe pieces
are located in Hangar #46 on Bowman field (LOU) Louisville, Ky.
arrangement for inspection of airframe components can be made at a
mutually agreeable time and date.
Art Jewett
8906 Nottingham Pkwy
Louisvillle, KY 40222-5219
502-426-0442 or---- artjewett@ juno.com
----------------------------------------------------------------
Engine group:
Vernier throttle & mixture cables $25 each
Master and starter solenoids. $10 each
L-R Start ignition switch $25
Faucett Primer pump. $50
Remote operated fuel shutoff valve.$20
Radios - Instruments
Altimeter 0-20,000' $100
Westach recording tach. $50
Hobbs meter. with oil pressure switch $25
Westach volt -amp gauge $25
Westach CHT/EGT with single point. $25
Westach oil temp - pressure guage $120
Whiskey compass $30
Hamilton Vertical card compass $50
Airspeed Indicator 0-220 MPH $75
Airspeed indicator 40-200 MPH $50
Airframe group is offered as a single item priced at $2,500.
All external surfaces have been filled, contour sanded,
primed and painted with Imron 508U.
This group is composed of:
LS1 Canard airfoil with carbon fiber spar
With counter balanced elevators.
Elevator trim control wheel and friction devise
mounted in center sub instrument panel.
Main wheels with dual brake system ie rudder pedal
mounted individual toe brakes on Pilots side and
single lever dual wheel braking actuator arm with
master cylinder mounted inside the left console
accessible by screw removal section of arm rest,.
Canard mounted Dual rudder pedals with return springs
attached to back side of engine fire wall with disconnect
cables.
Main wheels with individual brake cylinders and calipers with
removable bubble covers,
Removable tie down rings for each main wheel.
Set of three tie down screws with Nylon rope in canvas
bag.
Spare main wheel with tire and break disc stand offs with
brake disc mounted..
Canopy
Clear front hinged with gas spring assists mounted to back
side of header tank.
Over center locking by hinged tube with solid bullet nose
with spring return locking into the seat back bulkhead.
Lockable from inside or outside by Allen wrench.
Canopy opening via inserting Allen wrench into short steel
tube located at the rear on each side.
Wing
Trailing edge fairing to match fairing at junction
with fuselage.
Copper foil strip Nav antenna with BX connector cable mounted
on underside of wing center panel.
Tail cone
With copper foil Com antenna mounted inside the vertical
stabilizer and on the under side of tail cone.
Rear half of disconnect rudder cables running to tail wheel
and return cabled to rudder.
Aircraft Spruce donut shaped solid rubber home
builders special tail wheel with spare (6.25"x2.0").
Other items
Header and, main fuel tanks with sight gauges.
Faucett 3/8" fuel pump and bulb type emergency backup pump.
Removable locking door on external fill pipe.
Speed brake with accurator and locking devise mounted in the
center consul,
Aileron reflexer mounted in the left consul.
NACA air vents connected to eyeballs mounted in sub panels
below the main instrument panel. on each side.