Smoke not accepted from cygwin

[Nick Glencross]

Guys,

I have tried to submit a smoke from cygwin, but the server does not
accept the smoke file (which I've attached).

Can someone in-the-know about what criteria the server uses shed any
light on it? I note that the file is bzip'd whereas on Linux it is gzip'd.

For the record, after running Configure I replaced the Makefile in
dynclasses with 'all:' to allow the build to complete. This does not
affect the coverage of the tests.

Thanks,

Nick

/usr/bin/perl t/harness --html

# Failed test (t/op/trans.t at line 307)
# got: 'ok 1
# ok 2
# ok 3
# ok 4
# ok 5
# ok 6
# ok 7
# ok 8
# ok 9
# ok 10
# ok 11
# ok 12
# ok 13
# ok 14
# ok 15
# ok 16
# not 0.000000ok 17
# '
# expected: 'ok 1
# ok 2
# ok 3
# ok 4
# ok 5
# ok 6
# ok 7
# ok 8
# ok 9
# ok 10
# ok 11
# ok 12
# ok 13
# ok 14
# ok 15
# ok 16
# ok 17
# '
# Looks like you failed 1 test of 19.

# Failed test (t/pmc/signal.t at line 87)
# got: 'start
# never
# '
# expected: 'start
# '
# './parrot.exe "/tmp/parrot/t/pmc/signal_1.pasm"' failed with exit
code 72057594037927935
# Looks like you failed 1 test of 3.

# Failed test (t/library/pcre.t at line 33)
# got: 'ok 1
# Couldn't load 'libpcre': No such file or directory
# assertion
"(interpreter->ctx.bp->pmc_reg.registers[cur_opcode[2]])->pmc_ext"
failed: file "ops/core.ops", line 1195
# '
# expected: 'ok 1
# ok 2
# ok 3
# ok 4
# ok 5
# '
# Looks like you failed 1 test of 1.
smoke.html has been generated.
/usr/bin/perl util/smokeserv-client.pl smoke.html
* smokeserv-client v0.4 started.
* Bzip2 compression on
* Reading smoke "smoke.html" to upload... ok.
* Sending data to smokeserver "http://smoke.parrotcode.org/smoke/"...
error: The submitted smoke does not look like a smoke!
make: *** [smoke] Error 1

[Nick Glencross]

Strange, something has stripped the attachment (I didn't forget to
attach it, honest!). I'll try again in a few hours using SMTP instead of
NNTP.

Nick

[Nick Glencross]

Here (hopefully) is the generated smoke file which might hold some clues...

[Nick Glencross]

Nick Glencross wrote:

> Guys,
>
> I have tried to submit a smoke from cygwin, but the server does not
> accept the smoke file (which I've attached).
>
> Can someone in-the-know about what criteria the server uses shed any
> light on it? I note that the file is bzip'd whereas on Linux it is gzip'd.

Sure enough the issue looks bzip/gzip related. I didn't initially
realise that the smoke server is also in svn, so now it's pretty easy to
hunt down the problem.

I can see why the client would use the best compression available to it,
but doing the same on the server (which will then receive files that it
can't uncompress) is just plain odd.

Can someone install Compress:Bzip2 on the smoke server?

Ta,

Nick