Anyone want some cheap NEMA 17 steppers?

[Peter "Sci" Turpin]

Found an ebay seller in the USA with a limited stock of refurbished NEMA
17 steppers. They're not listed as NEMA 17, but found more info on the
model through another website.
http://cncsuperstore.com/index.php?route=product/product&manufacturer_id=15&product_id=64

They're 4-wire 1.8degree/200-step steppers with a 43.2oz/in 305mNm
torque. Relatively high-voltage with a range of 12-36v, so may not be
reliable for microstepping with low-cost drivers.

They're being sold in lots of 5 for $35. One lot including postage would
come to about �40, which would mean each stepper costing about �8 each.

I've contacted the seller and he's getting me a shipping quote based on
2 and 5 lots of 5. So if we order several lots, the price will come down
further through shipping savings. Total number of lots appears to be 25
currently.

The motors appear to be ideal for 3D printer projects and other small
CNC/robotics.

The listing is here for your perusal: http://www.ebay.com/itm/111056326418

Is anyone else interested in getting a lot or partial-lot along with me
and saving some cash?

Has anyone got any comment on the suitability/type of steppers, in case
I've found an appealing white elephant here?

I note the seller also has some other stepper lots for similar, but
slightly higher, prices. Some 4-wire, some 6. Suspect they would be
covered in the same shipping total if requested.

If there's interest and no technical objections to the choice, I'll
start a short-run pledge page. Will need the money quickly though, so
please have it ready to go if interested.


(PS; these are NEMA 17, not the NEMA 23 req for the engraver CNC. Still
looking there.)

[Adrian Godwin]

In the workshop, near the end of the member's shelves, is a box with a partially assembled Prusa. I think it's the one Billy's building.  It has two steppers at the top with only a date label, no other markings. They came from me and I think they're NEMA 23 : I'll donate another couple for the engraver if they're suitable.

--
You received this message because you are subscribed to the Google Groups "London Hackspace" group.
To unsubscribe from this group and stop receiving emails from it, send an email to london-hack-space+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.

[Billy]

They're Nema 23's. There's three of them.

They're a little too big for the Prusa parts that i've got.

I'll swap them for three of the Nema 17's.

On 16 May, 16:30, Adrian Godwin <artgod...@gmail.com> wrote:
> In the workshop, near the end of the member's shelves, is a box with a
> partially assembled Prusa. I think it's the one Billy's building.  It has
> two steppers at the top with only a date label, no other markings. They
> came from me and I think they're NEMA 23 : I'll donate another couple for
> the engraver if they're suitable.
>
> On Thu, May 16, 2013 at 4:20 PM, Peter "Sci" Turpin <s...@sci-fi-fox.com>wrote:
>
>
>
>
>
>
>
> > Found an ebay seller in the USA with a limited stock of refurbished NEMA
> > 17 steppers. They're not listed as NEMA 17, but found more info on the
> > model through another website.

> >http://cncsuperstore.com/**index.php?route=product/**
> > product&manufacturer_id=15&**product_id=64<http://cncsuperstore.com/index.php?route=product/product&manufacturer...>

>
> > They're 4-wire 1.8degree/200-step steppers with a 43.2oz/in 305mNm torque.
> > Relatively high-voltage with a range of 12-36v, so may not be reliable for
> > microstepping with low-cost drivers.
>
> > They're being sold in lots of 5 for $35. One lot including postage would
> > come to about £40, which would mean each stepper costing about £8 each.
>
> > I've contacted the seller and he's getting me a shipping quote based on 2
> > and 5 lots of 5. So if we order several lots, the price will come down
> > further through shipping savings. Total number of lots appears to be 25
> > currently.
>
> > The motors appear to be ideal for 3D printer projects and other small
> > CNC/robotics.
>

> > The listing is here for your perusal:http://www.ebay.com/itm/**
> > 111056326418 <http://www.ebay.com/itm/111056326418>

>
> > Is anyone else interested in getting a lot or partial-lot along with me
> > and saving some cash?
>
> > Has anyone got any comment on the suitability/type of steppers, in case
> > I've found an appealing white elephant here?
>
> > I note the seller also has some other stepper lots for similar, but
> > slightly higher, prices. Some 4-wire, some 6. Suspect they would be covered
> > in the same shipping total if requested.
>
> > If there's interest and no technical objections to the choice, I'll start
> > a short-run pledge page. Will need the money quickly though, so please have
> > it ready to go if interested.
>
> > (PS; these are NEMA 17, not the NEMA 23 req for the engraver CNC. Still
> > looking there.)
>
> > --
> > You received this message because you are subscribed to the Google Groups
> > "London Hackspace" group.
> > To unsubscribe from this group and stop receiving emails from it, send an

> > email to london-hack-space+unsubscribe@**googlegroups.com<london-hack-space%2Bunsu...@googlegroups.com>
> > .
> > For more options, visithttps://groups.google.com/**groups/opt_out<https://groups.google.com/groups/opt_out>
> > .

[Nick Johnson]

I'll happily buy a lot at that price.

-Nick

On Thu, May 16, 2013 at 4:20 PM, Peter "Sci" Turpin <s...@sci-fi-fox.com> wrote:

--
You received this message because you are subscribed to the Google Groups "London Hackspace" group.

[Dan Reid]

I would be interested in a lot

To unsubscribe from this group and stop receiving emails from it, send an email to london-hack-sp...@googlegroups.com.

[Peter "Sci" Turpin]

We only need three NEMA 23's for the engraver.

As the engraver is a project for the space, anyone want to pony up for
the extra three for this swap if there aren't enough going spare? Would
be cheaper than buying them independently.

NEMA 23's should be a drop-in replacement assuming they're not over 50mm
body-length. They 6 or 4-wire? We don't have the connector pin-out yet,
so 6-wire would allow flexibility.

[Adrian Godwin]

Billy has a mixture of NEMA 17 and 23s. I've got one more similar 17, which he can have (and free up a 23). Two more from that group purchase for Billy would be nice but the offer of two more 23s still stands if  not enough are available to replace his.

They're all 4-wire. I may have some old round-style 6-wire if they're required.

The steppers I have are unknown spec so probably not good enough for the Stratasys, in case anyone thinks that's a better use - if it needs 17s they'll have to be pretty good ones.

--
You received this message because you are subscribed to the Google Groups "London Hackspace" group.

[Peter "Sci" Turpin]

Heard back. Collective postage is $80 or $60 without tracking. Not as
large a saving as I'd have hoped, but I'd favour with tracking all the same.

$35 for 5, times the three lots people seem interested in; 15 steppers.
$30 for the one lot of 4 higher torque ones for swapping with Billy for
the Stratasys and CNC Mill.

Total 19 steppers, so highest postage would be ~$4.21ea.

Means for the order, each lot of 5 cheap ones would be $56.05 and the
lot of 4 stronger ones would be $46.84. Total;

$135+$80P&P= $215 (�ｿｽ142)

Lots of 5 to pay; �ｿｽ36.94 (�ｿｽ7.39 per stepper)
Lot of 4 to pay; �ｿｽ30.87 (�ｿｽ7.72 per stepper)

Before we go any further, any objections on price? *And any risk we'll
get stung at customs by importing 2nd-hand goods or electronics?* Is
there a best type to (legally!) request it be listed as on customs forms?

I've talked to the seller through my personal account. I can either pay
myself and take money directly, but will need it all in advance. Or
people can pay to the hackspace IF the space is okay with paying it on
to me. I suspect the former would have less fees involved. Or I can hand
the transaction over to someone with access to the space's paypal account.

On 16/05/2013 16:20, Peter "Sci" Turpin wrote:
> Found an ebay seller in the USA with a limited stock of refurbished NEMA
> 17 steppers. They're not listed as NEMA 17, but found more info on the
> model through another website.
> http://cncsuperstore.com/index.php?route=product/product&manufacturer_id=15&product_id=64
>
>
> They're 4-wire 1.8degree/200-step steppers with a 43.2oz/in 305mNm
> torque. Relatively high-voltage with a range of 12-36v, so may not be
> reliable for microstepping with low-cost drivers.
>
> They're being sold in lots of 5 for $35. One lot including postage would

> come to about �ｿｽ40, which would mean each stepper costing about �ｿｽ8 each.

[Simon Howes]

Get I add in an order for 8 of them?

On May 19, 2013 4:24 PM, "Peter "Sci" Turpin" <s...@sci-fi-fox.com> wrote:

Heard back. Collective postage is $80 or $60 without tracking. Not as large a saving as I'd have hoped, but I'd favour with tracking all the same.

$35 for 5, times the three lots people seem interested in; 15 steppers.
$30 for the one lot of 4 higher torque ones for swapping with Billy for the Stratasys and CNC Mill.

Total 19 steppers, so highest postage would be ~$4.21ea.

Means for the order, each lot of 5 cheap ones would be $56.05 and the lot of 4 stronger ones would be $46.84. Total;

$135+$80P&P= $215 (£142)

Lots of 5 to pay; £36.94 (£7.39 per stepper)
Lot of 4 to pay; £30.87 (£7.72 per stepper)

Before we go any further, any objections on price? *And any risk we'll get stung at customs by importing 2nd-hand goods or electronics?* Is there a best type to (legally!) request it be listed as on customs forms?

I've talked to the seller through my personal account. I can either pay myself and take money directly, but will need it all in advance. Or people can pay to the hackspace IF the space is okay with paying it on to me. I suspect the former would have less fees involved. Or I can hand the transaction over to someone with access to the space's paypal account.

On 16/05/2013 16:20, Peter "Sci" Turpin wrote:

Found an ebay seller in the USA with a limited stock of refurbished NEMA
17 steppers. They're not listed as NEMA 17, but found more info on the
model through another website.
http://cncsuperstore.com/index.php?route=product/product&manufacturer_id=15&product_id=64


They're 4-wire 1.8degree/200-step steppers with a 43.2oz/in 305mNm
torque. Relatively high-voltage with a range of 12-36v, so may not be
reliable for microstepping with low-cost drivers.

They're being sold in lots of 5 for $35. One lot including postage would

come to about £40, which would mean each stepper costing about £8 each.

I've contacted the seller and he's getting me a shipping quote based on
2 and 5 lots of 5. So if we order several lots, the price will come down
further through shipping savings. Total number of lots appears to be 25
currently.

The motors appear to be ideal for 3D printer projects and other small
CNC/robotics.

The listing is here for your perusal: http://www.ebay.com/itm/111056326418

Is anyone else interested in getting a lot or partial-lot along with me
and saving some cash?

Has anyone got any comment on the suitability/type of steppers, in case
I've found an appealing white elephant here?

I note the seller also has some other stepper lots for similar, but
slightly higher, prices. Some 4-wire, some 6. Suspect they would be
covered in the same shipping total if requested.

If there's interest and no technical objections to the choice, I'll
start a short-run pledge page. Will need the money quickly though, so
please have it ready to go if interested.


(PS; these are NEMA 17, not the NEMA 23 req for the engraver CNC. Still
looking there.)

[Peter "Sci" Turpin]

For 8 lots??

Each lot is a lot of 5 steppers. I don't think the seller will split
lots. I'd recommend getting 2 lots then.

On 19/05/2013 17:26, Simon Howes wrote:
> Get I add in an order for 8 of them?
>
> On May 19, 2013 4:24 PM, "Peter "Sci" Turpin" <s...@sci-fi-fox.com

> http://cncsuperstore.com/__index.php?route=product/__product&manufacturer_id=15&__product_id=64

> <http://cncsuperstore.com/index.php?route=product/product&manufacturer_id=15&product_id=64>
>
>
> They're 4-wire 1.8degree/200-step steppers with a 43.2oz/in 305mNm
> torque. Relatively high-voltage with a range of 12-36v, so may
> not be
> reliable for microstepping with low-cost drivers.
>
> They're being sold in lots of 5 for $35. One lot including
> postage would
> come to about �40, which would mean each stepper costing about
> �8 each.
>
> I've contacted the seller and he's getting me a shipping quote
> based on
> 2 and 5 lots of 5. So if we order several lots, the price will
> come down
> further through shipping savings. Total number of lots appears
> to be 25
> currently.
>
> The motors appear to be ideal for 3D printer projects and other
> small
> CNC/robotics.
>
> The listing is here for your perusal:

> http://www.ebay.com/itm/__111056326418

> <http://www.ebay.com/itm/111056326418>
>
> Is anyone else interested in getting a lot or partial-lot along
> with me
> and saving some cash?
>
> Has anyone got any comment on the suitability/type of steppers,
> in case
> I've found an appealing white elephant here?
>
> I note the seller also has some other stepper lots for similar, but
> slightly higher, prices. Some 4-wire, some 6. Suspect they would be
> covered in the same shipping total if requested.
>
> If there's interest and no technical objections to the choice, I'll
> start a short-run pledge page. Will need the money quickly
> though, so
> please have it ready to go if interested.
>
>
> (PS; these are NEMA 17, not the NEMA 23 req for the engraver
> CNC. Still
> looking there.)
>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from it,

> send an email to london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
> For more options, visit https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.

>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from it, send

> an email to london-hack-sp...@googlegroups.com.

[Simon Howes]

Okay, I'll take 2 lots then (10 steppers)

an email to london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--
You received this message because you are subscribed to the Google Groups "London Hackspace" group.

To unsubscribe from this group and stop receiving emails from it, send an email to london-hack-space+unsubscribe@googlegroups.com.

[Peter "Sci" Turpin]

If I calculate correctly that'll put it at the limit for the weight
category, so no more additions to this order!

PLEDGE PAGE IS UP!
http://wiki.london.hackspace.org.uk/view/Cheap_steppers_pledge

We still need some backing for the single lot of 4 more powerful
steppers included in the order that will be exchanged with Billy for
steppers suitable for the Stratasys and Engraver rebuilds, so please
contribute a spare couple of quid to raise that �30.

Please pay money to the hackspace with the reference "CHEAPSTEP".

On 19/05/2013 18:20, Simon Howes wrote:
> Okay, I'll take 2 lots then (10 steppers)
>
> On May 19, 2013 5:11 PM, "Peter "Sci" Turpin" <s...@sci-fi-fox.com

> <mailto:s...@sci-fi-fox.com>> wrote:
>
> For 8 lots??
>
> Each lot is a lot of 5 steppers. I don't think the seller will split
> lots. I'd recommend getting 2 lots then.
>
> On 19/05/2013 17:26, Simon Howes wrote:
>
> Get I add in an order for 8 of them?
>
> On May 19, 2013 4:24 PM, "Peter "Sci" Turpin"
> <s...@sci-fi-fox.com <mailto:s...@sci-fi-fox.com>

> http://cncsuperstore.com/____index.php?route=product/____product&manufacturer_id=15&____product_id=64
> <http://cncsuperstore.com/__index.php?route=product/__product&manufacturer_id=15&__product_id=64>

> http://www.ebay.com/itm/____111056326418
> <http://www.ebay.com/itm/__111056326418>

> london-hack-space+unsubscribe@____googlegroups.com
> <http://googlegroups.com>
> <mailto:london-hack-space%__2Buns...@googlegroups.com
> <mailto:london-hack-space%252Buns...@googlegroups.com>__>.
> For more options, visit
> https://groups.google.com/____groups/opt_out
> <https://groups.google.com/__groups/opt_out>

> <https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>>.
>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from
> it, send
> an email to london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
> For more options, visit
> https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.
>
>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from it,
> send an email to london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
> For more options, visit https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.
>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from it, send

> an email to london-hack-sp...@googlegroups.com.

[Nick Johnson]

Apologies, but can I reconsider? I've realised that I don't really _need_ 5 new steppers. If anyone wants to pick up my batch, it's available.

-Nick

             <mailto:london-hack-space%__2Bunsu...@googlegroups.com
        <mailto:london-hack-space%252Bunsubscribe@googlegroups.com>__>.

an email to london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--
You received this message because you are subscribed to the Google Groups "London Hackspace" group.

To unsubscribe from this group and stop receiving emails from it, send an email to london-hack-space+unsubscribe@googlegroups.com.

[chrisbob12]

@Sci - not sure what the state of play is with this, but I'm up for a batch of five, though I can't pay till Friday (in practical terms, I may not be able to process it till the bank holiday)

If that works for you, I'm up for it, if I've missed the boat; c'est la vie.

Regards, Chris.

[Peter "Sci" Turpin]

I've swapped Nick's lot with one for you.
I've also rounded my total up to �40 to throw a few quid toward the
Stratasys & CNC Mill steppers.

I suspect waiting until friday won't be a problem, as we still need to
fill backers for those steppers that'll help the space.

[chrisbob12]

Thanks.

[Peter "Sci" Turpin]

Due to some bills I'll likely be waiting until Friday to pay as well. :P

On 20/05/2013 16:06, chrisbob12 wrote:
> Thanks.
>

[Peter "Sci" Turpin]

There's been some miscommunication about what steppers are needed for
what regarding the engraver & stratasys. Will aim to come in on Sunday
(or MAYBE sat afternoon) to hook up the offered steppers to the engraver
now I have most of the pinouts and make sure they're compatible. This
may mean making some changes to the order, and change payment prices a bit.

On 16/05/2013 16:20, Peter "Sci" Turpin wrote:

[Billy]

NP.

If the steppers i've offered aren't compatible for a swap, then add me
to one lot of the nema 17's.

On 25 May, 00:25, "Peter \"Sci\" Turpin" <s...@sci-fi-fox.com> wrote:
> There's been some miscommunication about what steppers are needed for
> what regarding the engraver & stratasys. Will aim to come in on Sunday
> (or MAYBE sat afternoon) to hook up the offered steppers to the engraver
> now I have most of the pinouts and make sure they're compatible. This
> may mean making some changes to the order, and change payment prices a bit.
>
> On 16/05/2013 16:20, Peter "Sci" Turpin wrote:
>
>
>
>
>
>
>
> > Found an ebay seller in the USA with a limited stock of refurbished NEMA
> > 17 steppers. They're not listed as NEMA 17, but found more info on the
> > model through another website.

> >http://cncsuperstore.com/index.php?route=product/product&manufacturer...

[Chris Brasted]

@Sci

How's it looking at the moment? Do you need payment? Happy to do Paypal or BACS if that suits you.

--
You received this message because you are subscribed to a topic in the Google Groups "London Hackspace" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe?hl=en-GB.
To unsubscribe from this group and all of its topics, send an email to london-hack-space+unsubscribe@googlegroups.com.

[Peter "Sci" Turpin]

Will hopefully know tomorrow. Now engraver's confirmed running with
Billy's stepper, gotta see what sort he wants on the order in exchange
for them.

On 27/05/2013 18:46, Chris Brasted wrote:
> @Sci
> How's it looking at the moment? Do you need payment? Happy to do Paypal
> or BACS if that suits you.
>
>
> On Mon, May 20, 2013 at 4:03 PM, Peter "Sci" Turpin <s...@sci-fi-fox.com
> <mailto:s...@sci-fi-fox.com>> wrote:
>
> I've swapped Nick's lot with one for you.
> I've also rounded my total up to �40 to throw a few quid toward the
> Stratasys & CNC Mill steppers.
>
> I suspect waiting until friday won't be a problem, as we still need
> to fill backers for those steppers that'll help the space.
>
>
> On 20/05/2013 09:45, chrisbob12 wrote:
>
> @Sci - not sure what the state of play is with this, but I'm up
> for a batch of five, though I can't pay till Friday (in
> practical terms, I may not be able to process it till the bank
> holiday)
>
> If that works for you, I'm up for it, if I've missed the boat;
> c'est la vie.
>
> Regards, Chris.
>
>
> --
> You received this message because you are subscribed to a topic in
> the Google Groups "London Hackspace" group.
> To unsubscribe from this topic, visit

> https://groups.google.com/d/__topic/london-hack-space/__09YQfRCPKqg/unsubscribe?hl=en-__GB
> <https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe?hl=en-GB>.

> To unsubscribe from this group and all of its topics, send an email

> to london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
> For more options, visit https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.
>
>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.

> To unsubscribe from this group and stop receiving emails from it, send

> an email to london-hack-sp...@googlegroups.com.

[Peter "Sci" Turpin]

Okay, all the details are finally sorted.
Please send �32 per lot of 5 to the hackspace with reference
"CHEAPSTEPPERS" and mark yourself off the list on the pledge-page.
http://wiki.london.hackspace.org.uk/view/Cheap_steppers_pledge

On 16/05/2013 16:20, Peter "Sci" Turpin wrote:

[Peter "Sci" Turpin]

All sorted now. �32 to the hackspace's account with reference
"CHEAPSTEPPERS"

On 27/05/2013 18:46, Chris Brasted wrote:

> @Sci
> How's it looking at the moment? Do you need payment? Happy to do Paypal
> or BACS if that suits you.
>
>
> On Mon, May 20, 2013 at 4:03 PM, Peter "Sci" Turpin <s...@sci-fi-fox.com
> <mailto:s...@sci-fi-fox.com>> wrote:
>
> I've swapped Nick's lot with one for you.
> I've also rounded my total up to �40 to throw a few quid toward the
> Stratasys & CNC Mill steppers.
>
> I suspect waiting until friday won't be a problem, as we still need
> to fill backers for those steppers that'll help the space.
>
>
> On 20/05/2013 09:45, chrisbob12 wrote:
>
> @Sci - not sure what the state of play is with this, but I'm up
> for a batch of five, though I can't pay till Friday (in
> practical terms, I may not be able to process it till the bank
> holiday)
>
> If that works for you, I'm up for it, if I've missed the boat;
> c'est la vie.
>
> Regards, Chris.
>
>
> --
> You received this message because you are subscribed to a topic in
> the Google Groups "London Hackspace" group.
> To unsubscribe from this topic, visit

> https://groups.google.com/d/__topic/london-hack-space/__09YQfRCPKqg/unsubscribe?hl=en-__GB
> <https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe?hl=en-GB>.

> To unsubscribe from this group and all of its topics, send an email

> to london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
> For more options, visit https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.
>
>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.

> To unsubscribe from this group and stop receiving emails from it, send

> an email to london-hack-sp...@googlegroups.com.

[chrisbob12]

Done. Thank you.

[Peter "Sci" Turpin]

Noted it on the pledge page.

On 31/05/2013 00:08, chrisbob12 wrote:
> Done. Thank you.

[chrisbob12]

Thanks for noting it too. I was tired and missed that.

[Simon Howes]

Woups, will pay in a bit when work here dies down.
Rushie rushie!

On May 31, 2013 8:13 AM, "chrisbob12" <chris...@yahoo.com> wrote:

Thanks for noting it too. I was tired and missed that.

[Peter "Sci" Turpin]

That'd be appreciated Simon. Can you also note it on the wiki when you
have? It's the only way I know when to request the purchase be made.

On 31/05/2013 09:58, Simon Howes wrote:
> Woups, will pay in a bit when work here dies down.
> Rushie rushie!
>
> On May 31, 2013 8:13 AM, "chrisbob12" <chris...@yahoo.com

> <mailto:chris...@yahoo.com>> wrote:
>
> Thanks for noting it too. I was tired and missed that.
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from it,
> send an email to london-hack-sp...@googlegroups.com

> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.

[Peter "Sci" Turpin]

Still waiting on payment from Simon and Billy.

[Simon Howes]

Paid now.
sorry for the delay.

Can't seem to update the wiki though. Apparently I am not a member of group users. Hmmm.
Can some loving soul tell me how to do this, or update it for me?

--
You received this message because you are subscribed to the Google Groups "London Hackspace" group.

To unsubscribe from this group and stop receiving emails from it, send an email to london-hack-space+unsubscribe@googlegroups.com.

[Billy]

I paid it on Friday.

Didn't update the wiki though, as my e inter access is playing up, and
i've been ld u[ with arthritis, so couldn't get down to the space.

On 5 June, 15:56, Simon Howes <simonhowes...@googlemail.com> wrote:
> Paid now.
> sorry for the delay.
>
> Can't seem to update the wiki though. Apparently I am not a member of group
> users. Hmmm.
> Can some loving soul tell me how to do this, or update it for me?
> On Jun 5, 2013 1:26 PM, "Peter "Sci" Turpin" <s...@sci-fi-fox.com> wrote:
>
>
>
>
>
>
>
> > Still waiting on payment from Simon and Billy.
>
> > On 16/05/2013 16:20, Peter "Sci" Turpin wrote:
>
> >> Found an ebay seller in the USA with a limited stock of refurbished NEMA
> >> 17 steppers. They're not listed as NEMA 17, but found more info on the
> >> model through another website.

> >>http://cncsuperstore.com/**index.php?route=product/**
> >> product&manufacturer_id=15&**product_id=64<http://cncsuperstore.com/index.php?route=product/product&manufacturer...>

>
> >> They're 4-wire 1.8degree/200-step steppers with a 43.2oz/in 305mNm
> >> torque. Relatively high-voltage with a range of 12-36v, so may not be
> >> reliable for microstepping with low-cost drivers.
>
> >> They're being sold in lots of 5 for $35. One lot including postage would
> >> come to about £40, which would mean each stepper costing about £8 each.
>
> >> I've contacted the seller and he's getting me a shipping quote based on
> >> 2 and 5 lots of 5. So if we order several lots, the price will come down
> >> further through shipping savings. Total number of lots appears to be 25
> >> currently.
>
> >> The motors appear to be ideal for 3D printer projects and other small
> >> CNC/robotics.
>

> >> The listing is here for your perusal:http://www.ebay.com/itm/**
> >> 111056326418 <http://www.ebay.com/itm/111056326418>

>
> >> Is anyone else interested in getting a lot or partial-lot along with me
> >> and saving some cash?
>
> >> Has anyone got any comment on the suitability/type of steppers, in case
> >> I've found an appealing white elephant here?
>
> >> I note the seller also has some other stepper lots for similar, but
> >> slightly higher, prices. Some 4-wire, some 6. Suspect they would be
> >> covered in the same shipping total if requested.
>
> >> If there's interest and no technical objections to the choice, I'll
> >> start a short-run pledge page. Will need the money quickly though, so
> >> please have it ready to go if interested.
>
> >> (PS; these are NEMA 17, not the NEMA 23 req for the engraver CNC. Still
> >> looking there.)
>
> > --
> > You received this message because you are subscribed to the Google Groups
> > "London Hackspace" group.
> > To unsubscribe from this group and stop receiving emails from it, send an

> > email to london-hack-space+unsubscribe@**googlegroups.com<london-hack-space%2Bunsu...@googlegroups.com>
> > .
> > For more options, visithttps://groups.google.com/**groups/opt_out<https://groups.google.com/groups/opt_out>
> > .

[Simon Howes]

Are these coming now then? :)

To unsubscribe from this group and stop receiving emails from it, send an email to london-hack-sp...@googlegroups.com.

[chrisbob12]

+1 on that: what's the status?

[Simon Howes]

Hate to microstep this, but what's the status?

On Jun 20, 2013 4:32 PM, "chrisbob12" <chris...@yahoo.com> wrote:

+1 on that: what's the status?

[Peter "Sci" Turpin]

Russ let me know on the 11th that they'd been purchased, so should be on
their way. Will email and request the tracking info.

On 21/06/2013 10:39, Simon Howes wrote:
> Hate to microstep this, but what's the status?
>
> On Jun 20, 2013 4:32 PM, "chrisbob12" <chris...@yahoo.com

> <mailto:chris...@yahoo.com>> wrote:
>
> +1 on that: what's the status?
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from it,
> send an email to london-hack-sp...@googlegroups.com

> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.

[Chris Brasted]

Thanks Peter, that's good to know.

I'm planning on either building a second reprap, or a largish CNC
gantry, though it may take a while to acquire parts.

What are you planning for yours?

> You received this message because you are subscribed to a topic in the

> Google Groups "London Hackspace" group.

> To unsubscribe from this topic, visit
> https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe.
> To unsubscribe from this group and all of its topics, send an email to

[Peter "Sci" Turpin]

Called parcelforce. We have a customs fee of �28.25 to pay. So an extra
�4.71 per lot is needed from everyone.
They can take payment online, so I'm going to send my money to the
space's account as before and then we can arrange delivery or collect it
ourselves from NW1.

[Peter "Sci" Turpin]

An additional tally for the customs fees has been added to the pledge page.
Billy, you told me directly that you had paid your portion of the
original pledge. Please update it on the wiki page.

And for mine I intend to put my makerslide to good use. Planning a 3D
printer with a cubic-foot print volume. Aluminium profile frame,
leadscrews..

On 21/06/2013 11:55, Chris Brasted wrote:

[Chris Brasted]

Paid and updated wiki

On Jun 21, 2013 12:14 PM, "Peter "Sci" Turpin" <s...@sci-fi-fox.com> wrote:

Called parcelforce. We have a customs fee of £28.25 to pay. So an extra £4.71 per lot is needed from everyone.
They can take payment online, so I'm going to send my money to the space's account as before and then we can arrange delivery or collect it ourselves from NW1.

On 21/06/2013 11:55, Chris Brasted wrote:

Thanks Peter, that's good to know.

I'm planning on either building a second reprap, or a largish CNC
gantry, though it may take a while to acquire parts.

What are you planning for yours?

On 6/21/13, Peter "Sci" Turpin <s...@sci-fi-fox.com> wrote:

Russ let me know on the 11th that they'd been purchased, so should be on
their way. Will email and request the tracking info.

On 21/06/2013 10:39, Simon Howes wrote:

Hate to microstep this, but what's the status?

On Jun 20, 2013 4:32 PM, "chrisbob12" <chris...@yahoo.com
<mailto:chris...@yahoo.com>> wrote:

     +1 on that: what's the status?

     --
     You received this message because you are subscribed to the Google
     Groups "London Hackspace" group.
     To unsubscribe from this group and stop receiving emails from it,

     send an email to london-hack-space+unsubscribe@googlegroups.com

     <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
     For more options, visit https://groups.google.com/groups/opt_out.


--
You received this message because you are subscribed to the Google
Groups "London Hackspace" group.
To unsubscribe from this group and stop receiving emails from it, send

an email to london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--
You received this message because you are subscribed to a topic in the
Google Groups "London Hackspace" group.
To unsubscribe from this topic, visit
https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe.
To unsubscribe from this group and all of its topics, send an email to

london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--
You received this message because you are subscribed to a topic in the Google Groups "London Hackspace" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe.

To unsubscribe from this group and all of its topics, send an email to london-hack-space+unsubscribe@googlegroups.com.

[Chris Brasted]

mmm... Cubic foot and lead screws sounds good.

On Jun 21, 2013 12:21 PM, "Peter "Sci" Turpin" <s...@sci-fi-fox.com> wrote:

An additional tally for the customs fees has been added to the pledge page.
Billy, you told me directly that you had paid your portion of the original pledge. Please update it on the wiki page.

And for mine I intend to put my makerslide to good use. Planning a 3D printer with a cubic-foot print volume. Aluminium profile frame, leadscrews..

On 21/06/2013 11:55, Chris Brasted wrote:

Thanks Peter, that's good to know.

I'm planning on either building a second reprap, or a largish CNC
gantry, though it may take a while to acquire parts.

What are you planning for yours?

On 6/21/13, Peter "Sci" Turpin <s...@sci-fi-fox.com> wrote:

Russ let me know on the 11th that they'd been purchased, so should be on
their way. Will email and request the tracking info.

On 21/06/2013 10:39, Simon Howes wrote:

Hate to microstep this, but what's the status?

On Jun 20, 2013 4:32 PM, "chrisbob12" <chris...@yahoo.com
<mailto:chris...@yahoo.com>> wrote:

     +1 on that: what's the status?

     --
     You received this message because you are subscribed to the Google
     Groups "London Hackspace" group.
     To unsubscribe from this group and stop receiving emails from it,

     send an email to london-hack-space+unsubscribe@googlegroups.com

     <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
     For more options, visit https://groups.google.com/groups/opt_out.


--
You received this message because you are subscribed to the Google
Groups "London Hackspace" group.
To unsubscribe from this group and stop receiving emails from it, send

an email to london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--
You received this message because you are subscribed to a topic in the
Google Groups "London Hackspace" group.
To unsubscribe from this topic, visit
https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe.
To unsubscribe from this group and all of its topics, send an email to

london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--
You received this message because you are subscribed to a topic in the Google Groups "London Hackspace" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe.

To unsubscribe from this group and all of its topics, send an email to london-hack-space+unsubscribe@googlegroups.com.

[Peter "Sci" Turpin]

Trying to make it rock solid. Got some ideas for alternate printheads,
so of which might vibrate a bit.
Thinking TR8 size threads will probably do, TR10 at a pinch. Just trying
to work out the best rigid mounting arrangement using 20x20 profile.

On 21/06/2013 12:24, Chris Brasted wrote:
> mmm... Cubic foot and lead screws sounds good.
>
> On Jun 21, 2013 12:21 PM, "Peter "Sci" Turpin" <s...@sci-fi-fox.com

> <mailto:s...@sci-fi-fox.com>> wrote:
>
> An additional tally for the customs fees has been added to the
> pledge page.
> Billy, you told me directly that you had paid your portion of the
> original pledge. Please update it on the wiki page.
>
> And for mine I intend to put my makerslide to good use. Planning a
> 3D printer with a cubic-foot print volume. Aluminium profile frame,
> leadscrews..
>
> On 21/06/2013 11:55, Chris Brasted wrote:
>
> Thanks Peter, that's good to know.
>
> I'm planning on either building a second reprap, or a largish CNC
> gantry, though it may take a while to acquire parts.
>
> What are you planning for yours?
>
> On 6/21/13, Peter "Sci" Turpin <s...@sci-fi-fox.com

> <mailto:s...@sci-fi-fox.com>> wrote:
>
> Russ let me know on the 11th that they'd been purchased, so
> should be on
> their way. Will email and request the tracking info.
>
> On 21/06/2013 10:39, Simon Howes wrote:
>
> Hate to microstep this, but what's the status?
>
> On Jun 20, 2013 4:32 PM, "chrisbob12"
> <chris...@yahoo.com <mailto:chris...@yahoo.com>

> <mailto:chris...@yahoo.com

> <mailto:chris...@yahoo.com>>> wrote:
>
> +1 on that: what's the status?
>
> --
> You received this message because you are
> subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving
> emails from it,
> send an email to

> london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>
>
> <mailto:london-hack-space%__2Buns...@googlegroups.com <mailto:london-hack-space%252Buns...@googlegroups.com>__>.
> For more options, visit
> https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.

>
>
> --
> You received this message because you are subscribed to
> the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails
> from it, send
> an email to

> london-hack-space+unsubscribe@__googlegroups.com

> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
> For more options, visit

> https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.

>
>
>
> --
> You received this message because you are subscribed to a
> topic in the
> Google Groups "London Hackspace" group.
> To unsubscribe from this topic, visit

> https://groups.google.com/d/__topic/london-hack-space/__09YQfRCPKqg/unsubscribe
> <https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe>.

> To unsubscribe from this group and all of its topics, send
> an email to

> london-hack-space+unsubscribe@__googlegroups.com

> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
> For more options, visit

> https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.

>
>
>
>
>
> --
> You received this message because you are subscribed to a topic in
> the Google Groups "London Hackspace" group.
> To unsubscribe from this topic, visit

> https://groups.google.com/d/__topic/london-hack-space/__09YQfRCPKqg/unsubscribe
> <https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe>.

> To unsubscribe from this group and all of its topics, send an email

> to london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
> For more options, visit https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.

>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from it, send

> an email to london-hack-sp...@googlegroups.com.

[Chris Brasted]

I'm intrigued by why a print head might vibrate, good luck with the project!

RichRap's blog
http://richrap.blogspot.co.uk/
...has a number of reprap mods/improvements which I'm interested in
trying, and the gantry project plan B is intended to tackle CNC foam
cutting, with a view to laminating things like glider wings, however,
it has to get in the queue ;)

[Peter "Sci" Turpin]

Vortex-stabilised fused particle deposition. Nice theory, unsure if
it'll be precise enough though. We shall see! Regular printhead first tho.

[Chris Brasted]

Whoo! What advantage are you after?

[Peter "Sci" Turpin]

Hoping small particles will mean much finer detail and better bonding.

[cepm...@yahoo.co.uk]

A demand for import duties has arrived.

Tracking Ref. EC065027271GB

£28.25 to pay

www.parcelforce.com click on "receiving" Have your bank card ready!


Phil

--
" et cognoscetis veritatem et veritas liberabit vos.



"On Fri, 21 Jun 2013 11:24:04 +0100, Peter "Sci" Turpin

[Simon Howes]

Paid! :)

On Jun 21, 2013 1:27 PM, <cepm...@yahoo.co.uk> wrote:

A demand for import duties has arrived.

Tracking Ref. EC065027271GB

£28.25 to pay

www.parcelforce.com   click on "receiving"   Have your bank card ready!


Phil

--
" et cognoscetis veritatem et veritas liberabit vos.



"On Fri, 21 Jun 2013 11:24:04 +0100, Peter "Sci" Turpin <s...@sci-fi-fox.com> wrote:

Russ let me know on the 11th that they'd been purchased, so should be on their way. Will email and request the tracking info.

On 21/06/2013 10:39, Simon Howes wrote:

Hate to microstep this, but what's the status?

On Jun 20, 2013 4:32 PM, "chrisbob12" <chris...@yahoo.com
<mailto:chris...@yahoo.com>> wrote:

    +1 on that: what's the status?

    --
    You received this message because you are subscribed to the Google
    Groups "London Hackspace" group.
    To unsubscribe from this group and stop receiving emails from it,

    send an email to london-hack-space+unsubscribe@googlegroups.com

    <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
    For more options, visit https://groups.google.com/groups/opt_out.


--
You received this message because you are subscribed to the Google
Groups "London Hackspace" group.
To unsubscribe from this group and stop receiving emails from it, send

an email to london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--
You received this message because you are subscribed to the Google Groups "London Hackspace" group.

To unsubscribe from this group and stop receiving emails from it, send an email to london-hack-space+unsubscribe@googlegroups.com.

[Peter "Sci" Turpin]

Please mark it on the wiki then ;)

On 24/06/2013 10:14, Simon Howes wrote:
> Paid! :)
>
> On Jun 21, 2013 1:27 PM, <cepm...@yahoo.co.uk

> <mailto:cepm...@yahoo.co.uk>> wrote:
>
> A demand for import duties has arrived.
>
> Tracking Ref. EC065027271GB
>
> �28.25 to pay
>

> www.parcelforce.com <http://www.parcelforce.com> click on

> "receiving" Have your bank card ready!
>
>
> Phil
>
> --
> " et cognoscetis veritatem et veritas liberabit vos.
>
>
>
> "On Fri, 21 Jun 2013 11:24:04 +0100, Peter "Sci" Turpin

> <s...@sci-fi-fox.com <mailto:s...@sci-fi-fox.com>> wrote:
>
> Russ let me know on the 11th that they'd been purchased, so
> should be on their way. Will email and request the tracking info.
>
> On 21/06/2013 10:39, Simon Howes wrote:
>
> Hate to microstep this, but what's the status?
>
> On Jun 20, 2013 4:32 PM, "chrisbob12" <chris...@yahoo.com
> <mailto:chris...@yahoo.com>

> <mailto:chris...@yahoo.com <mailto:chris...@yahoo.com>>>

> wrote:
>
> +1 on that: what's the status?
>
> --
> You received this message because you are subscribed to
> the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving
> emails from it,
> send an email to

> london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>
>
> <mailto:london-hack-space%__2Buns...@googlegroups.com

> <mailto:london-hack-space%252Buns...@googlegroups.com>__>.
> For more options, visit
> https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.

>
>
> --
> You received this message because you are subscribed to the
> Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails
> from it, send

> an email to london-hack-space+unsubscribe@__googlegroups.com

> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
> For more options, visit

> https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.

>
>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from it,

> send an email to london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
> For more options, visit https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.

>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from it, send

> an email to london-hack-sp...@googlegroups.com.

[Simon Howes]

So, I've paid. Will update the wiki when I get home. My kindle fire doesn't seem to want to let me.

Has this been collected yet? Doesnt it get shipped back if you leave it over a week without paying customs?

            <mailto:london-hack-space%__2Bunsu...@googlegroups.com
            <mailto:london-hack-space%252Bunsubscribe@googlegroups.com>__>.

an email to london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--
You received this message because you are subscribed to the Google Groups "London Hackspace" group.

To unsubscribe from this group and stop receiving emails from it, send an email to london-hack-space+unsubscribe@googlegroups.com.

[Nigel Worsley]

> Has this been collected yet?

Doesn't look like it http://www.parcelforce.com/track-trace?page_type=parcel-tracking-details&parcel_number=EC065027271GB

> Doesnt it get shipped back if you leave it over a week without paying customs?

The card requesting payment arrived 5 days ago, should still be OK.

Nigle

[Simon Howes]

Cool? So we're 4.71 short of having steppers?
Pay, billah pay :)

[Billy]

Paid £5 into the donation box last night.

I forgot to update the wiki.

On Wednesday, June 26, 2013 5:36:14 PM UTC+1, Simon Howes wrote:

Cool? So we're 4.71 short of having steppers?
Pay, billah pay :)

On Jun 26, 2013 4:20 PM, "Nigel Worsley" <nig...@googlemail.com> wrote:

Has this been collected yet?

Doesn't look like it http://www.parcelforce.com/track-trace?page_type=parcel-tracking-details&parcel_number=EC065027271GB

Doesnt it get shipped back if you leave it over a week without paying customs?

The card requesting payment arrived 5 days ago, should still be OK.

Nigle

--
You received this message because you are subscribed to the Google Groups "London Hackspace" group.

To unsubscribe from this group and stop receiving emails from it, send an email to london-hack-sp...@googlegroups.com.

[Billy]

Just updated the wiki.

[Peter "Sci" Turpin]

Contacting Russ to see about delivery..

On 26/06/2013 23:14, Billy wrote:
>
> Just updated the wiki.
>
>
>
> On Wednesday, June 26, 2013 10:33:34 PM UTC+1, Billy wrote:
>
>
> Paid �5 into the donation box last night.
>
> I forgot to update the wiki.
>
>
>
>
> On Wednesday, June 26, 2013 5:36:14 PM UTC+1, Simon Howes wrote:
>
> Cool? So we're 4.71 short of having steppers?
> Pay, billah pay :)
>
> On Jun 26, 2013 4:20 PM, "Nigel Worsley" <nig...@googlemail.com>
> wrote:
>
> Has this been collected yet?
>
>
> Doesn't look like it

> http://www.parcelforce.com/__track-trace?page_type=parcel-__tracking-details&parcel___number=EC065027271GB

> <http://www.parcelforce.com/track-trace?page_type=parcel-tracking-details&parcel_number=EC065027271GB>
>
> Doesnt it get shipped back if you leave it over a week
> without paying customs?
>
>
> The card requesting payment arrived 5 days ago, should still
> be OK.
>
> Nigle
>
> --
> You received this message because you are subscribed to the
> Google Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails

> from it, send an email to london-hack-sp...@__googlegroups.com.
> For more options, visit
> https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.

[Mark Steward]

He's in Glastonbury.  I don't know if he's planning to be online periodically, but it's probably best to email trus...@london.hackspace.org.uk if you need payment sorted before Monday.

Mark

an email to london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--
You received this message because you are subscribed to the Google Groups "London Hackspace" group.

To unsubscribe from this group and stop receiving emails from it, send an email to london-hack-space+unsubscribe@googlegroups.com.

[Peter "Sci" Turpin]

Email sent. It's been there a week already, so I'd rather get it sorted
sooner than later.

On 27/06/2013 01:25, Mark Steward wrote:
> He's in Glastonbury. I don't know if he's planning to be online
> periodically, but it's probably best to email
> trus...@london.hackspace.org.uk

> <mailto:trus...@london.hackspace.org.uk> if you need payment sorted

> before Monday.
>
>
> Mark
>
>
> On Thu, Jun 27, 2013 at 1:20 AM, Peter "Sci" Turpin <s...@sci-fi-fox.com
> <mailto:s...@sci-fi-fox.com>> wrote:
>
> Contacting Russ to see about delivery..
>
>
> On 26/06/2013 23:14, Billy wrote:
>
>
> Just updated the wiki.
>
>
>
> On Wednesday, June 26, 2013 10:33:34 PM UTC+1, Billy wrote:
>
>
> Paid �5 into the donation box last night.
>
> I forgot to update the wiki.
>
>
>
>
> On Wednesday, June 26, 2013 5:36:14 PM UTC+1, Simon Howes
> wrote:
>
> Cool? So we're 4.71 short of having steppers?
> Pay, billah pay :)
>
> On Jun 26, 2013 4:20 PM, "Nigel Worsley"

> <nig...@googlemail.com <mailto:nig...@googlemail.com>>

> wrote:
>
> Has this been collected yet?
>
>
> Doesn't look like it

> http://www.parcelforce.com/____track-trace?page_type=parcel-____tracking-details&parcel_____number=EC065027271GB
> <http://www.parcelforce.com/__track-trace?page_type=parcel-__tracking-details&parcel___number=EC065027271GB>

>
>
> <http://www.parcelforce.com/__track-trace?page_type=parcel-__tracking-details&parcel___number=EC065027271GB
> <http://www.parcelforce.com/track-trace?page_type=parcel-tracking-details&parcel_number=EC065027271GB>>
>
> Doesnt it get shipped back if you leave it over
> a week
> without paying customs?
>
>
> The card requesting payment arrived 5 days ago,
> should still
> be OK.
>
> Nigle
>
> --
> You received this message because you are
> subscribed to the
> Google Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving
> emails
> from it, send an email to

> london-hack-sp...@__googlegrou__ps.com <http://googlegroups.com>.
> For more options, visit
> https://groups.google.com/____groups/opt_out
> <https://groups.google.com/__groups/opt_out>

> <https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>>.
>
>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from
> it, send

> an email to london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.

> For more options, visit
> https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.
>
>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from it,

> send an email to london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.

> For more options, visit https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.
>
>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from it, send

> an email to london-hack-sp...@googlegroups.com.

[Mark Steward]

Not received yet. Are your emails buffered somehow?


Mark

[Mark Steward]

Scratch that, it's just arrived.

[Peter "Sci" Turpin]

Got an email back from Paddy. Apparently it requires a reference number
that isn't the tracking number, which will presumably be in Russ's
possession, so we'll have to wait for him to get back.

Reading the terms and conditions however we're going to be charged a
storage fee of �5.50 as Monday will be past the 10-day free-holding
period. Past 20 days it's an additional �1.35 per parcel per day. :(

[Paddy Duncan]

Yes it is the Parcelforce Invoice number, and I've looked in the mail box
and Russ's box to no avail..
Paddy

[Peter "Sci" Turpin]

Doesn't matter. I just phoned Parcelforce, explained and they gave me
the payment reference which I've now emailed you Paddy.

[pad...@padski.co.uk]

Sending it to me will achieve nothing.......

Sent from my thing.

[Peter "Sci" Turpin]

Is anyone other than Russ able to make such a payment from the space's
account?

[Mark Steward]

Sorted, delivery will be attempted tomorrow.

[Chris Brasted]

I think, more to the point, who is authorised (from the post office's POV) to collect. Presumably a receipt for the duty payment could be translated into a refund from the space (or it could be paid online?)

 >>>>> <mailto:trustees@london.hackspace.org.uk> if you need payment

 >>>>> send an email to london-hack-space+unsubscribe@googlegroups.com.

 >>>>> For more options, visit https://groups.google.com/groups/opt_out.
 >>>>>
 >>>>>
 >>>>
 >>>> --
 >>>> You received this message because you are subscribed to the Google
 >>>> Groups "London Hackspace" group.
 >>>> To unsubscribe from this group and stop receiving emails from it,

 >>>> send an email to london-hack-space+unsubscribe@googlegroups.com.

 >>>> For more options, visit https://groups.google.com/groups/opt_out.
 >>>>
 >>>>
 >>
 >
 > --
 > You received this message because you are subscribed to the Google Groups
 > "London Hackspace" group.
 > To unsubscribe from this group and stop receiving emails from it, send an

 > email to london-hack-space+unsubscribe@googlegroups.com.

 > For more options, visit https://groups.google.com/groups/opt_out.
 >
 >
 >

--
You received this message because you are subscribed to the Google
Groups "London Hackspace" group.
To unsubscribe from this group and stop receiving emails from it, send

an email to london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.


--
You received this message because you are subscribed to the Google
Groups "London Hackspace" group.
To unsubscribe from this group and stop receiving emails from it, send

an email to london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--
You received this message because you are subscribed to a topic in the Google Groups "London Hackspace" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe.
To unsubscribe from this group and all of its topics, send an email to london-hack-space+unsubscribe@googlegroups.com.

[Chris Brasted]

Posts crossed in the ether. Thanks for that!

You received this message because you are subscribed to a topic in the Google Groups "London Hackspace" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe.
To unsubscribe from this group and all of its topics, send an email to london-hack-sp...@googlegroups.com.

[Peter "Sci" Turpin]

Awesome! I probably won't be able to get in in time to receive it
myself, but can come in Saturday to divide the order up if people can
tell me the location of their boxes.

[chrisbob12]

Slightly problematic, since I never had a box at the old space, and have yet to establish one at the new space. I should be able to come over on Saturday late afternoon, and hope to figure it out from there. I was hoping to pick up my lot of five and take them away for onward management. I'd appreciate if anyone involved in this transaction could let me know if they'll be around then, or could park my motors where I can find them.

Regards, Chris.

[chrisbob12]

Have they been delivered?

[Peter "Sci" Turpin]

http://www.parcelforce.com/track-trace?page_type=parcel-tracking-details&parcel_number=EC065027271GB

Evidently not. They were loaded onto a delivery truck at 20 past
midnight though, so odds are they'll be delivered on Saturday. Convenient!

Someone keep an ear out for the doorbell please? I won't be in until the
afternoon. o_o;

On 29/06/2013 00:05, chrisbob12 wrote:
> Have they been delivered?

[Chris Brasted]

Oh yes, the tracking details. Durr. Thanks. Maybe see you this afternoon. I'll probably in about five.

On Jun 29, 2013 1:46 AM, "Peter "Sci" Turpin" <s...@sci-fi-fox.com> wrote:

http://www.parcelforce.com/track-trace?page_type=parcel-tracking-details&parcel_number=EC065027271GB

Evidently not. They were loaded onto a delivery truck at 20 past midnight though, so odds are they'll be delivered on Saturday. Convenient!

Someone keep an ear out for the doorbell please? I won't be in until the afternoon. o_o;

On 29/06/2013 00:05, chrisbob12 wrote:

Have they been delivered?

--
You received this message because you are subscribed to the Google
Groups "London Hackspace" group.
To unsubscribe from this group and stop receiving emails from it, send

an email to london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--

You received this message because you are subscribed to a topic in the Google Groups "London Hackspace" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe.

To unsubscribe from this group and all of its topics, send an email to london-hack-space+unsubscribe@googlegroups.com.

[Chris Brasted]

Tracking still only shows it going out for despatch, so presumably, not delivered today.

On Jun 29, 2013 1:46 AM, "Peter "Sci" Turpin" <s...@sci-fi-fox.com> wrote:

http://www.parcelforce.com/track-trace?page_type=parcel-tracking-details&parcel_number=EC065027271GB

Evidently not. They were loaded onto a delivery truck at 20 past midnight though, so odds are they'll be delivered on Saturday. Convenient!

Someone keep an ear out for the doorbell please? I won't be in until the afternoon. o_o;

On 29/06/2013 00:05, chrisbob12 wrote:

Have they been delivered?

--
You received this message because you are subscribed to the Google
Groups "London Hackspace" group.
To unsubscribe from this group and stop receiving emails from it, send

an email to london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--

You received this message because you are subscribed to a topic in the Google Groups "London Hackspace" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe.
To unsubscribe from this group and all of its topics, send an email to london-hack-space+unsubscribe@googlegroups.com.

[Peter "Sci" Turpin]

Phoned them up to check. Yeah, delivery is scheduled for Monday not
today. They pre-load the vans several days in advance. :P

Do we have a note on the front door instructing deliveries to be made at
the rear? If not, can we get one stuck up there before Monday?

On 29/06/2013 13:46, Chris Brasted wrote:
> Tracking still only shows it going out for despatch, so presumably, not
> delivered today.
>
> On Jun 29, 2013 1:46 AM, "Peter "Sci" Turpin" <s...@sci-fi-fox.com

> <mailto:s...@sci-fi-fox.com>> wrote:
>
> http://www.parcelforce.com/__track-trace?page_type=parcel-__tracking-details&parcel___number=EC065027271GB

> <http://www.parcelforce.com/track-trace?page_type=parcel-tracking-details&parcel_number=EC065027271GB>
>
> Evidently not. They were loaded onto a delivery truck at 20 past
> midnight though, so odds are they'll be delivered on Saturday.
> Convenient!
>
> Someone keep an ear out for the doorbell please? I won't be in until
> the afternoon. o_o;
>
> On 29/06/2013 00:05, chrisbob12 wrote:
>
> Have they been delivered?
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from
> it, send

> an email to london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
> For more options, visit
> https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.

>
>
>
> --
> You received this message because you are subscribed to a topic in
> the Google Groups "London Hackspace" group.
> To unsubscribe from this topic, visit

> https://groups.google.com/d/__topic/london-hack-space/__09YQfRCPKqg/unsubscribe
> <https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe>.

> To unsubscribe from this group and all of its topics, send an email

> to london-hack-space+unsubscribe@__googlegroups.com
> <mailto:london-hack-space%2Bunsu...@googlegroups.com>.
> For more options, visit https://groups.google.com/__groups/opt_out
> <https://groups.google.com/groups/opt_out>.

>
>
> --
> You received this message because you are subscribed to the Google
> Groups "London Hackspace" group.
> To unsubscribe from this group and stop receiving emails from it, send

> an email to london-hack-sp...@googlegroups.com.

[Chris Brasted]

I've set myself up with a members box. It's a used club mate box with my name and alias, and some making tape over the club mate logo at the end. It's down the second aisle, third bay, second shelf from the floor. I'd be grateful to know if my motors find their way there.

an email to london-hack-space+unsubscribe@googlegroups.com.

For more options, visit https://groups.google.com/groups/opt_out.

--
You received this message because you are subscribed to a topic in the Google Groups "London Hackspace" group.

To unsubscribe from this topic, visit https://groups.google.com/d/topic/london-hack-space/09YQfRCPKqg/unsubscribe.
To unsubscribe from this group and all of its topics, send an email to london-hack-space+unsubscribe@googlegroups.com.

[Russ Garrett]

On 27 June 2013 16:39, Peter "Sci" Turpin <s...@sci-fi-fox.com> wrote:
> Got an email back from Paddy. Apparently it requires a reference number that
> isn't the tracking number, which will presumably be in Russ's possession, so
> we'll have to wait for him to get back.

Just for future reference I was never in possession of any magic
number - the only number given to me by the seller was the tracking
number. If another number existed I would expect it to be on the
missed-delivery slip, which I didn't have anything to do with.

Cheers,

--
Russ Garrett
ru...@garrett.co.uk

[Peter "Sci" Turpin]

Thanks for that Russ and all the help ordering them!
I sorted the actual items out tonight.

There was no missed-delivery slip or notice of holding fees that I could
see. Have to chalk it up to "fun with imports" I guess.