Hi chaps. Im going to be looking on Ebay but it seems that we need a
storage locker for our dewar if we want to get busy with the fizzy.
I've measured up and we need at least 45cm x 45cm x 80cm space to fit
the dewar inside. If anyone has any suggestions (that other auction
site, pp maybe?) then do let me know.
> Hi chaps. Im going to be looking on Ebay but it seems that we need a
> storage locker for our dewar if we want to get busy with the fizzy.
> I've measured up and we need at least 45cm x 45cm x 80cm space to fit
> the dewar inside. If anyone has any suggestions (that other auction
> site, pp maybe?) then do let me know.
> Hi chaps. Im going to be looking on Ebay but it seems that we need a
> storage locker for our dewar if we want to get busy with the fizzy.
> I've measured up and we need at least 45cm x 45cm x 80cm space to fit
> the dewar inside. If anyone has any suggestions (that other auction
> site, pp maybe?) then do let me know.
Not sure. For now Im happy to get the the NO2 one properly secured so
we can get it filled. Not a bad idea Peter but I'll need to check if
there is anything we need to be "compliant" with.
B
On 7 October 2012 15:02, Peter "Sci" Turpin <s...@sci-fi-fox.com> wrote:
> Some steel angle-iron, mesh and an hour with the arc-welder.
> On that matter though, what other gas bottles need to be caged?
> On 07/10/2012 13:45, Benjamin Blundell wrote:
>> Hi chaps. Im going to be looking on Ebay but it seems that we need a
>> storage locker for our dewar if we want to get busy with the fizzy.
>> I've measured up and we need at least 45cm x 45cm x 80cm space to fit
>> the dewar inside. If anyone has any suggestions (that other auction
>> site, pp maybe?) then do let me know.
On 7 October 2012 15:13, Benjamin Blundell <onida...@gmail.com> wrote:
> Not sure. For now Im happy to get the the NO2 one properly secured so
> we can get it filled. Not a bad idea Peter but I'll need to check if
> there is anything we need to be "compliant" with.
There isn't - that would be fine. Just weld something together and
stick a hasp + padlock on it. It would probably be better to do it
ourselves because the dewar will need to wheel in and out, and I doubt
you'll find a locker like that.
> Understood. I thought that might have been the issue. Good news
> all-round then, especially as yes, I didnt find very many.
> On 7 October 2012 22:46, Russ Garrett <r...@garrett.co.uk> wrote:
>> On 7 October 2012 15:13, Benjamin Blundell <onida...@gmail.com> wrote:
>>> Not sure. For now Im happy to get the the NO2 one properly secured so
>>> we can get it filled. Not a bad idea Peter but I'll need to check if
>>> there is anything we need to be "compliant" with.
>> There isn't - that would be fine. Just weld something together and
>> stick a hasp + padlock on it. It would probably be better to do it
>> ourselves because the dewar will need to wheel in and out, and I doubt
>> you'll find a locker like that.
Three sided cage (fourth side will be the wall that it is screwed to) half
built and in the room with the Dewar. In the trolley and with the delivery
tube fitted the cage needs to be higher than the 800mm mentioned so will
hold off finishing until exact dimensions and location has been finalised.
It might be an idea to have in the cage the PPE (gloves, apron, goggles
etc.) required for safe use. If required I will make provision for those
too.
Phil
-- " et cognoscetis veritatem et veritas liberabit vos. "
On Sun, 07 Oct 2012 13:45:59 +0100, Benjamin Blundell <onida...@gmail.com>
wrote:
> Hi chaps. Im going to be looking on Ebay but it seems that we need a
> storage locker for our dewar if we want to get busy with the fizzy.
> I've measured up and we need at least 45cm x 45cm x 80cm space to fit
> the dewar inside. If anyone has any suggestions (that other auction
> site, pp maybe?) then do let me know.
The gloves are an essential - the correct ones for sure. My
measurements for the cage were rough ones made by eye with a tape
measure as a guide for looking at storage lockers. when you are next
in phil, we should talk more about it.
B
On 9 October 2012 06:45, <cepmen...@yahoo.co.uk> wrote:
> Three sided cage (fourth side will be the wall that it is screwed to) half
> built and in the room with the Dewar. In the trolley and with the delivery
> tube fitted the cage needs to be higher than the 800mm mentioned so will
> hold off finishing until exact dimensions and location has been finalised.
> It might be an idea to have in the cage the PPE (gloves, apron, goggles
> etc.) required for safe use. If required I will make provision for those
> too.
> Phil
> --
> " et cognoscetis veritatem et veritas liberabit vos. "
> On Sun, 07 Oct 2012 13:45:59 +0100, Benjamin Blundell <onida...@gmail.com>
> wrote:
>> Hi chaps. Im going to be looking on Ebay but it seems that we need a
>> storage locker for our dewar if we want to get busy with the fizzy.
>> I've measured up and we need at least 45cm x 45cm x 80cm space to fit
>> the dewar inside. If anyone has any suggestions (that other auction
>> site, pp maybe?) then do let me know.
