So I've got a vector file I'd like to use to generate a 3d object in
OpenSCAD to create an STL file from to print on the space printer.
Problem is, no matter what program I export the DXF file for the
linear_extrude in OpenSCAD it whines about unsupported lines and such.
I've exported it to every revision of DXF under the sun, re-did the
vector to ensure it was closed etc to no avail.
Does anyone have any experience with this at all? Logs are below, and
I've attached an SVG of the vector..
This is what I get when I export it from Inkscape after fixing up the
vector points:
WARNING: Unsupported DXF Entity `SPLINE' (37x) in
`C:/Users/nog3/Desktop/Imperial_Eagle2.dxf'.
WARING: Open paths in dxf_liniear_extrude(file =
"C:/Users/nog3/Desktop/Imperial_Eagle2.dxf", layer = ""):
153.06600 78.53500 ... 145.54400 83.59400
158.00700 98.60000 ... 170.04700 93.09700
136.12800 70.45800 ... 142.59600 43.57000
144.03800 66.55900 ... 147.64800 65.52100
148.58600 55.91500 ... 153.07200 64.37500
155.84300 64.00900 ... 159.31500 63.90400
180.65600 39.84400 ... 165.15400 65.35500
168.58800 67.59600 ... 170.65300 69.87500
172.47300 73.17200 ... 173.31900 75.87400
173.73700 78.36900 ... 173.84300 82.21600
173.34900 85.43800 ... 172.28000 88.73000
140.79400 35.89900 ... 148.58600 12.13300
152.67700 10.18500 ... 149.65700 7.16500
155.40400 8.04200 ... 149.57900 20.38600
155.98900 14.52100 ... 155.98900 25.57400
108.45600 83.59400 ... 100.93400 78.53500
113.20600 35.89900 ... 105.41400 12.13300
98.01100 25.57400 ... 98.01100 14.52100
104.42100 20.38600 ... 98.59600 8.04200
104.34300 7.16500 ... 101.32300 10.18500
106.35100 65.52100 ... 109.96200 66.55900
111.40400 43.57000 ... 117.87200 70.45900
95.99300 98.60000 ... 83.95200 93.09800
81.72000 88.73000 ... 80.65100 85.43800
80.15700 82.21700 ... 80.26300 78.36900
80.68100 75.87400 ... 81.52700 73.17200
83.34700 69.87500 ... 85.41200 67.59600
88.84500 65.35600 ... 73.34400 39.84400
94.68500 63.90400 ... 98.15700 64.00900
100.92700 64.37500 ... 105.41400 55.91500
Compiling design (CSG Products normalization)...
CSG generation finished.
Total rendering time: 0 hours, 0 minutes, 0 seconds
And this is what I get when I export directly from illustrator into
supposedly the right version of DXF to work with OpenSCAD:
WARNING: Unsupported DXF Entity `SPLINE' (7x) in
`C:/Users/nog3/Desktop/Imperial_Eagle2.dxf'.
WARNING: Unsupported DXF Entity `VERTEX' (53x) in
`C:/Users/nog3/Desktop/Imperial_Eagle2.dxf'.
WARNING: Unsupported DXF Entity `POLYLINE' (5x) in
`C:/Users/nog3/Desktop/Imperial_Eagle2.dxf'.
WARNING: Unsupported DXF Entity `HATCH' (10x) in
`C:/Users/nog3/Desktop/Imperial_Eagle2.dxf'.
WARNING: Unsupported DXF Entity `SEQEND' (5x) in
`C:/Users/nog3/Desktop/Imperial_Eagle2.dxf'.
Compiling design (CSG Products normalization)...
CSG generation finished.
Total rendering time: 0 hours, 0 minutes, 0 seconds
