Methane geoengineering paper

6 views
Skip to first unread message

Andrew Lockley

unread,
Jan 29, 2010, 10:22:43 AM1/29/10
to geoengineering
Hi,

I paste below my Methane Geoengineering paper for ASL.  The deadline is tomorrow, so I'd appreciate some quick comments if possible.  The references are yet to be formatted (given as DOIs in text), and I've not yet done my final check read, but other than that, it's done.

It's my first paper, but hopefully it's not too much of a shambles.  I'm interested to know whether the qualitative evaluation is sufficiently rigorous.  (Not a lot I can do now if it's not, though!)

I am having trouble finding references for basic scientific data, such as ignition points and the life of OH radicals.  No-one's researching such basic things as they were established long ago, so how do you reference them?

Any ideas or comments are welcome, no matter how disparaging they may be!

Thanks

A

Geoengineering treatment of methane

Methane is a significant GHG, and substantial reservoirs are vulnerable to instability due to AGW.  Excursions, from permafrost and clathrates especially, act a positive feedback to AGW. Existing concentrations of well-mixed atmospheric methane substantially exceed pre-industrial levels.

Various geoengineering methods are herein proposed for containment of methane, and/or accelerated oxidation to CO2 (a gas with a lower GWP over all timescales).

A basic qualitative analysis of each technique is undertaken, to direct further study.  Consideration is also given to the potential capacity of each technique to treat the total likely excursions of methane expected as a result of AGW.

.Acknowledgements

Ideas used in this paper have been worked on by the following:

§  Alvia Gaskill

§  N. Currier

§  Alan Gardain

§  Stephen Salter

§  David Schware

§  Eugene Gordon

§  Mike McCracken

§  Luxi Zhou

§  Dan Wylie-Sears

They have not endorsed the whole work.


 

 

Background

LeLieveld et al (1998) state that: Methane concentrations have  increased from about 0.75–1.73 μmol/mol during the past 150 years to date of paper; ~70% of the total source is anthropogenic; methane accounts for 22% of the radiative  forcing by all long-lived greenhouse gases (2.6 W m−2) ; GWP is 21 (kgCH4/kgCO2) over 100yr {{10.1034/j.1600-0889.1998.t01-1-00002.x}}

However, the GWP of methane has probably been underestimated.(Shindell et al, 2009){{10.1126/science.1174760}}

The paleoclimatic record implies the possibility of dramatic warming in the Arctic in response to AGW http://www.micropress.org/stratigraphy/papers/Stratigraphy_6_4_265-275.pdf 

Dickens et al (1997) note that “Gas hydrates in oceanic sediments may in fact comprise the Earth's largest fossil-fuel reservoir. But the amount of methane stored in gas-hydrate and free-gas zones is poorly constrained.”{{ 10.1038/385426a0}}

Reagan & Moridis (2008) note that “shallow deposits can be very unstable and release significant quantities of methane under the influence of as little as 1°C of seafloor temperature increase”{{ 10.1029/2008JC004938} However,{{ 10.1029/2008GL035291}} Lamarque, predicts.Using an observed 1% ratio to estimate the amount of methane reaching the atmosphere, our analysis leads to a relatively small methane flux of approximately 5–21 Tg(CH4)/year”.

Archer (2007) notes “The hydrate reservoir is so large that if 10% of the methane were released to the atmosphere within a few years, it would have an impact on the Earth’s radiation budget equivalent to a factor of 10 increase in atmospheric CO2

 

Permafrost environments within the Siberian Arctic are natural sources of

methane.{{ 10.1111/j.1365-2486.2007.01331.x}}

The paleoclimatic record indicates a significant role for abrupt methane excursions in major climatic events such as the PETM (Schmitt & Shindell, 2003) {{ 10.1029/2002PA000757}} and the P-T Mass Extinction (Krull & Retallack, 2000). {{10.1130/0016-7606(2000)112<1459:CDPFPA>2.0.CO;2}}

Atmospheric methane is naturally broken down by oxidation, ultimately to water and carbon dioxide.  This oxidation process is primarily conducted by reaction with OH radicals (GHANSHYAM L. VAGHJIANI* & A. R. RAVISHANKARA, 1991) {{ 10.1038/350406a0}}

Introduction

Herein is set out possible treatments for:

1)     Unstable methane reservoirs (including frozen organic detritus),

2)     Aquatic methane production and excursions

3)     Concentrated atmospheric methane

4)     Diffuse atmospheric methane

Treatment methods are rated by estimated scale of practicable application as

1)     ‘limited’ – able to treat some excursions

2)     ‘significant’ –climatically significant capacity

3)     ‘full’ – able to manage the entire methane budget

Treatments are assessed against the following criteria:

1)     Infrastructure/implementation cost

2)     Energy cost

3)     Expected efficacy

4)     Development cost & uncertanties

5)     Environmental impacts

6)     Potential for CCS

A ranking is given simply of ‘positive’, ‘neutral’ or ‘negative’ in each category, with accompanying commentary.  Rankings are a matter of personal judgement and are used to crudely rank proposals. An asterisk marks outliers.

The intention of ranking the treatments is simply to highlight proposals worthy of further study, and is not set out as fully considered analysis.

0: - SRM geoengineering

The potential use of geoengineering techniques such as Cloud Condensation Nuclei {{10.1038/347339b0}} and Stratospheric Sulphur Aerosols{{ 10.1098/rsta.2008.0132}} is widely acknowledged.  Such techniques may be regionally or globally applied, and thus can contribute to cooling and hence stabilising methane deposits.  Further, these techniques may additionally have a role in cooling the planet in response to a sudden warming caused by an excursion of methane into the atmosphere.  The opportunities to employ such techniques is the subject of ongoing research,  For comparison, the use of these techniques to react to a large flux of methane is evaluated below, using the same rating scale.  We conclude the scale of the technique to be ‘full’, considering the work of Robock {{10.1029/2008JD011652}}

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

-1

0

0

-1

-1

0

Moderate deployment costs

Low ongoing energy requirements

Potential to counter warming without allowing enhanced remediation

Costly to develop and test at scale.

Possible climatic disruption

None

Score = -3         Scale = Full

 

Section 1 - Pre-emptive treatment of methane reservoirs

Unstable reservoirs of methane may be mined, or otherwise treated to initiate controlled release of methane for collection and treatment.

 

Soil heating

Excursion of methane from soil and mire is seasonal, and is temperature dependent.{{ 10.1002/ppp.443}} {{ doi:10.1029/2003GL018680}} Soil temperature may be raised to hasten the excursion and permit collection and treatment. 

Soil Heating using Polytunnels

Agricultural 'polytunnels' create warmed microclimates, which may be used to trigger excursions into the contained tunnel environment.  Depending on extraction timescales, equipment re-use is possible.

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

-1

0

-1

1

-1

-1

Large treatment area, long timescales

Economic recovery unlikely

Slow, leaky.

Simple to construct and test.

Widespread disruption to ecosystems.

Low concentrations.

 

Score = -3         Scale = Significant

 

 

Soil heating using heat pumps

Active or passive heat pumps may be used to warm soils and mires. Energy from warmer soils and water bodies, or from solar heating, could be used as the heat source.  It may be possible to extract methane from deep permafrost while shallower layers serve as a cap.

 

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

-1

0

1

1

-1

-1

Large treatment area required

Renewables, possible recovery

Reasonably effective recovery from limited areas may be possible.

Inexpensive to test and trial

Major ecosystem disruption.

Volumes too low and locations too remote to allow CCS

Score = -1         Scale = Significant

 

Soil aeration

Physical treatment of the soil to enhance aeration may be possible (e.g. ploughing).  This may cause decomposition of organic matter to occur in an oxygen-rich environment.  However, it may simply stimulate the excursion of methane, and further research is needed.

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

-1

0

0

1

-1

-1

Large area required

Operations require little energy, other than tractor fuel

Unproven.  Treats surface layers only.

Inexpensive to test and trial

Large scale mechanical processing needed.

Impossible

Score = -2         Scale = Significant

 

Mining clathrates

Established proposals{{ 10.1146/annurev.eg.15.110190.000413}}{{10.1016/S0378-3820(01)00145-X}} exist for the commercial mining of methane clathrate as an energy source.  At cost, this may be extended to uneconomic deposits.

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

1

1

1

1

1

1

Economic recovery possible

Concentrated energy source

Highly effective at treating concentrated deposits.

Already under consideration without subsidy.

Mostly limited and localised impacts, save leakage and landslide.

Ideal for capture

 

Score = 6          Scale = Significant

 

Burning of clathrates

In clathrate deposits where mining or other recovery is impractical or uneconomic, controlled or partially-controlled releases for burning may be initiated.  Disruption of clathrates could be done by heating, blasting, or the use of machinery.  Burning could be performed at the surface as detailed above.  Alternatively, underwater burning could be oxygenated with piped air, either within submersible plant, or possibly in open water.

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

-1

0

0

-1

1

-1

Significant and complex engineering, often at depth, without recovery

Minimal energy consumption

Depends of containment efficacy

Requires significant development, with no economic benefits

Mostly limited and localised impacts, save possible shelf collapse

Capture likely impractical at scales uneconomic for mining.

 

Score = -2         Scale = Significant

 

 


2: Aquatic methane production & excursions

.

Methane fluxes to the atmosphere from lakes are principally by ebullition (bubbling) from thawing shoreline permafrost {{10.1038/nature05040}}.  Larger bubbles, and those released from shallow deposits may reach the surface and deposit their methane load into the atmosphere.{{can}} Aqueous solutions of methane are typically biodegraded before reaching the atmosphere.{{can}}

 

Lake sealing

 

Covering lakes with an airtight seal will prevent methane fluxes to the atmosphere.  Non-biodegradable foaming agents could be used to trap methane bubbles in a stable layer.  Burning or collecting the foam is then possible.  In shallow lakes a miscible foaming agent could be used, but in deeper lakes an oily foaming agent could be floated on the surface, This technique would severely affect the oxygen supply, and thus tend to create further methane by forcing anaerobic respiration to dominate.  Aeration equipment could be used to avoid the collapse of the lake ecosystem.

 

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

-1

0

1

1

-1

0

Large treatment area, ongoing maintenance

Energy recovery difficult

Reasonably effective containment possible

Simple to test and trial

Blanket coverage of lakes required

Potentially possible in larger lakes

 

Score = 0          Scale = Significant

 

Mixing of aquatic strata

Methane bubbles may dissolve into the water column, with shallow releases having much higher chance of entering the atmosphere{{ 10.1029/2005JC003183}}.

Geoengineering techniques for mixing ocean strata have already been proposed {{ 10.1007/s10584-005-5933-0}}.  Water mixing may promote methane dissolution by means of temperature adjustment, downwelling and gas concentration adjustment. 

Smaller bubbles are relatively prone to dissolution due to their surface area and ascent time.  Mixing equipment may cleave bubbles, aiding dissolution.  Enhanced flow rates on sea and lake floors may encourage the cleavage of smaller bubbles from gas reservoirs.

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

0

1

-1

1

0

-1

Treatable area uncertain, subject to ongoing research

Established technology has been proposed for mixing using wind/wave energy.

No evidence the approach will work.

Simple, low technology testing.

Some disruption to ecosystems may occur.  Effects likely local & limited.

Impractical

 

Score = 0          Scale = Significant

 

 

Bubble capture

Funnelling bubbles into capture pipework may be practical.   As an alternative to capture, the funnel may be perforated to release small bubbles, aiding dissolution and aquatic methantrophy.

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

0

1

1

1

0

1

Costs depend on concentration of sources

Net energy source, although economic recovery may not be possible

Potentially very effective for locally concentrated aquatic excursions.

Easy to prototype

May disrupt marine ecosystems. Could disrupted upwelling/downwelling currents

Concentrated gas could be collected and transported to CCS plant.

 

Score = 4          Scale = Significant

 

Water aeration

Successful oxygenation of anoxic waters and sediments facilitates aerobic methanotrophy, which is a significant factor in the local methane budget.{{ 10.1016/S0016-7037(01)00625-1}} .  Oxygenation also impedes methanogenesis. Aeration technology using bubblers and impellers is widely studied and implemented, e.g {{ 10.1021/es040471b}}, including cold water systems {{10.1061/(ASCE)0733-9372(1990)116:2(376))}}

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

-1

0

-1

1

1

-1

Large numbers of lakes require treatment

Renewable power readily available

Unproven.  Mixing may not penetrate anoxic sediments and/or aquatic strata.

Widely commercially available

Low impact on most ecosystems

Impossible

 

Score = 1          Scale = Significant

 

Biological oxidation in aquatic environments

Aerobic metabolism of methane could be enhanced by depositing or fertilising methanotrophs, where their relative absence limits metabolism. The concurrent distribution or fertilisation of autotrophic flora (e.g. phytoplankton) may additionally benefit by enhancing oxygenation, although consideration must be given to preventing consequential eutrophication.  This technique partners with mechanical aeration.

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

0

0

-1

1

1

-1

Continual resupply of active organisms required.

Distribution /manufacture energy only

Unlikely that existing microorganisms can be significantly enhanced.

Relatively cheap to test with non-GMO organisms.

Significant ecosystem damage unlikely.

Impossible

 

Score = 0          Scale = Significant

 

 


3: Remediation of concentrated atmospheric methane

.

In some areas, concentrations of atmospheric methane are occasionally so high that it forms a flammable fuel-air mix at small scales{{can}}. This opens up the possibility of an ignition-based oxidation process in appropriate areas.

 

Regenerative Thermal Oxidation

Reverse-flow regenerative thermal oxidation plant is widely available commercially

It is well tested for a variety of gases {{ 10.1061/(ASCE)0733-9372(2002)128:4(313)}}.  The lower limit of self-sustaining operation is ~0.1-0.2% vol, {{ http://seca.doe.gov/publications/proceedings/03/carbon-seq/PDFs/122.pdf}}  This is significantly lower than the concentration limit for flammability, but far higher than the current ambient concentration. 

Plant or intake pipe would be sited adjacent to excursions.

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

-1

1

1

1

1

0

Significant cost to install at scale

Recovery viable

Proven efficacy in correct concentrations

Based on established technology

Proven and benign in operation

Sensitive to concentration.

 

Score = 3          Scale = Significant

 

 

Electrical ignition

Small sparking devices that sit atop lakes, seas and soils can be manufactured using vehicle spark plug technology.  Robust construction is required to withstand the heating and blast effects.

The low electrical power requirements could be provided by micro-renewables, typically located outside the blast area.

Distribution could be manual, mechanical or air-dropped.

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

0

0

-1

1

0

-1

In some specific areas may be relatively inexpensive

No overall impact, save manufacture/delivery

Limited efficacy and only in certain areas

Based on established technology

Causes frequent explosions

Impossible

 

Score = -1         Scale = Limited

 

Thermal ignition using incendiary munitions

 

Very large excursions of methane can potentially occur as a result of the breakdown of clathrate deposits.{{ 10.1073/pnas.0402909101}}  Detection of natural excursions may be possible using satellite, surface or airborne monitoring.   Thermal ignition of the resulting concentrated plumes is possible using incendiary munitions fired from air, surface vessels or field artillery.  Existing medium-calibre artillery has a range of 40km, therefore shorelines, shelf edges and other linear features may be flared with no more than 25 guns per 1000km, even allowing for substantial overlap to give a belt of coverage, capacity for ignition at altitude, & redundancy.

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

0

0

-1

-1

1

-1

Somewhat costly, especially offshore

Neutral

Partially-effective treatment of last resort for large fluxes

Monitoring and control a significant challenge

Explosions will typically take place well above ground level

Impossible

 

Score = -2         Scale = Limited

 

 

 


4: Diffuse atmospheric methane

Rarified methane will oxidise if heated.  Catalysts allow remediation at temperatures as low as 500C and concentrations as low as 0.2% (Lee, 2006){{ 10.1016/j.cattod.2006.05.035}}   All techniques below can be used on concentrated or diffuse sources.

 

Thermal oxidation by concentrated solar power

Concentrated solar power is able to drive the temperatures needed for thermal oxidation of methane, even when rarefied in the atmosphere. Such plants are also able to generate electricity on site, which will give the mechanical power needed to drive the necessary fans and steer the mirror arrays. Heat imparted into the air can be recovered by means of a boiler, like that in a power station. It may be more efficient to use the CSP plants to warm a heat-exchanger fluid to avoid the need to heat air directly, although losses will occur as a result of the transfer process.  Further research on efficiency losses is required.

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

0

0

1

1

1

0

Efficiency costs requires extra plant

Process efficiency reduced significantly

Complete treatment of limited volume

Cheap to build test plant

No impact, other than increasing CSP plant area.

Uses ambient air

Score = 3          Scale = Significant, (full with dedicated plant)

 

Thermal oxidation by waste heat

Where high-grade waste heat is available, heat exchangers may be used to transfer this heat to air, potentially in the presence of catalysts.

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

-1

0

1

1

1

-1

Typically requires expensive catalysts

Uses waste heat

Effective treatment of limited volume

Cheap to build test plant

No impact, especially if NOx catalysed.

Distributed, small sources.

Score = 1          Scale = Limited

 

Compression ignition

Diesel engines heat air by compression to achieve thermal ignition. By designing engines with sufficient compression ratios, spontaneous oxidation of atmospheric methane can be achieved.  Modified vehicle engines driven electrically when not in use could be employed, and the possible future generation of plug-in hybrids makes this possible at useful scale. Unmodified jet engines typically have higher compression ratios.  NOx is a climatically-useful (although toxic and environmentally harmful) by-product of compression heating, which can be catalytically mitigated if required. 

Energy expended in compression is partially recovered during expansion, and can also be recovered by heat exchangers acting to cool the pressurised gas.  However, frictional and heat transfer losses are inevitable.  Dedicated plant could be developed with vast, insulated cylinders or similarly-designed jets, to minimise losses.  Such plant may benefit from catalysts to enhance methane oxidation, which are unlikely to be suitable for use in working engines.

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

-1

-1

1

1

-1

-1

Requires modification of global vehicle fleet or dedicated plant

Frictional & thermal losses, vehicle efficiency issues

Complete treatment of treated volume

Cheap to build test plant

Increased engine wear and early scrapping. NOx.

Uses ambient air

Score = -2         Scale = Full

 

Chemical degradation

Degredation of methane by hydroxyl radicals is the primary fate of atmospheric methane at present.  ((VAGHJIANI & RAVISHANKARA, 1991), 1991). OH lifetimes in the atmosphere are of the order of seconds, and point injection of OH radicals are therefore unlikely to mix well.  Raising concentrations of photochemical precursors to OH may be more successful.

The principle natural method for the creation of OH radicals is the photolysis of ozone (itself a GHG).  Ozone may be manufactured at high energy cost and injected directly.  A lower-energy method is the manipulation of ozone precursors, including NOx, which catalyses the ozone production photochemistry cycle. NOx emissions lead typically to a net negative radiative forcing effect by this method{{10.1029/2000GL012573}}.  NOx is evaluated below.

 

Cost

Energy

Efficacy

Development

Environmental

CO2 capture

0

0

1

0

0

-1

Moderate investment in plant

Chemical manufacture.

High with correct design

Development at scale possibly costly.

Potential damage to atmos. chemistry

Diffuse

Score = 0          Scale = Full

 

Conclusion

There is no one technique which offers a ‘magic bullet’ to the problem of atmospheric methane, as all solutions detailed have potential or identified major drawbacks or limitations of scale.  However, cheap, simple research can be carried out to test most proposals. Higher-scored and fuller-scale techniques merit further detailed study.

Andrew Lockley

unread,
Jan 29, 2010, 11:35:59 AM1/29/10
to geoengineering
I've had a complaint that some people can't read the pasted paper, so I'm sending at as an attachment.

Prompt  comments welcome. - deadline tomorrow.!

A

2010/1/29 Andrew Lockley <andrew....@gmail.com>
methane paper.doc

Veli Albert Kallio

unread,
Jan 29, 2010, 4:44:59 PM1/29/10
to Andrew Lockley, Geoengineering FIPC
Hi Andrew,
 
We have an extremely important author to add on this particular subject. Could you contact me to discuss this further over the weekend.
+44-7794-981238.  Our FIPC Campaign (Frozen Isthmuses' Protection Campaign of the Arctic Oceans has methane management one of its key campaingning areas we, therefore, have investested lots of our funds and time on this particular area.)
 
Therere are some very influential people doing excellent work in this matter and would do a fabulous contribution for our geoeng community.
 
Many thanks,
 
Albert
 

Date: Fri, 29 Jan 2010 16:35:59 +0000
Subject: [geo] Re: Methane geoengineering paper
From: andrew....@gmail.com
To: geoengi...@googlegroups.com
--
You received this message because you are subscribed to the Google Groups "geoengineering" group.
To post to this group, send email to geoengi...@googlegroups.com.
To unsubscribe from this group, send email to geoengineerin...@googlegroups.com.
For more options, visit this group at http://groups.google.com/group/geoengineering?hl=en.


We want to hear all your funny, exciting and crazy Hotmail stories. Tell us now
Reply all
Reply to author
Forward
0 new messages