Adaptec SATA 1210SA+ Freebsd 6.0
Filip Wuytack
I just installed freebsd 6 and it all runs fine, but when I try (via
sysinstall) to make a new label on a partition on ar0, the system says:
'ata2 disconnect requested' and freezes. I there something extra I need to
do make ar0 to work properly?
Many thanks,
Filip
This is the output of my dmesg.boot:
=============================================
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RELEASE #0: Thu Nov 3 09:36:13 UTC 2005
ro...@x64.samsco.home:/usr/obj/usr/src/sys/GENERIC
ACPI APIC Table: <DELL PE500SC >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) III CPU family 1133MHz (1130.45-MHz 686-class
CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 1207894016 (1151 MB)
avail memory = 1173618688 (1119 MB)
ioapic0: Changing APIC ID to 1
ioapic1: Changing APIC ID to 2
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-15 on motherboard
ioapic1 <Version 1.1> irqs 16-31 on motherboard
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL PE500SC> on motherboard
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link LNKA> on acpi0
pci_link1: <ACPI PCI Link LNKB> on acpi0
pci_link2: <ACPI PCI Link LNKC> on acpi0
pci_link3: <ACPI PCI Link LNKD> on acpi0
pci_link4: <ACPI PCI Link LNKE> irq 11 on acpi0
pci_link5: <ACPI PCI Link LNKF> on acpi0
pci_link6: <ACPI PCI Link LNKG> on acpi0
pci_link7: <ACPI PCI Link LNKH> irq 10 on acpi0
pci_link8: <ACPI PCI Link LNKI> on acpi0
pci_link9: <ACPI PCI Link LNKJ> on acpi0
pci_link10: <ACPI PCI Link LNKK> on acpi0
pci_link11: <ACPI PCI Link LNKL> on acpi0
pci_link12: <ACPI PCI Link LNKM> on acpi0
pci_link13: <ACPI PCI Link LNKN> on acpi0
pci_link14: <ACPI PCI Link LNKO> irq 5 on acpi0
pci_link15: <ACPI PCI Link LNKP> on acpi0
pci_link16: <ACPI PCI Link LUSB> irq 3 on acpi0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> on acpi0
pci0: <ACPI PCI bus> on pcib0
fxp0: <Intel 82559 Pro/100 Ethernet> port 0xecc0-0xecff mem
0xfe102000-0xfe102fff,0xfe000000-0xfe0fffff irq 20 at device 2.0 on pci0
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:c0:9f:0a:3d:56
atapci0: <SiI 3112 SATA150 controller> port
0xecb8-0xecbf,0xecb0-0xecb3,0xeca0-0xeca7,0xec98-0xec9b,0xec80-0xec8f mem
0xfe103000-0xfe1031ff irq 23 at device 6.0 on pci0
ata2: <ATA channel 0> on atapci0
ata3: <ATA channel 1> on atapci0
amr0: <LSILogic MegaRAID 1.51> mem 0xfb000000-0xfb00ffff irq 30 at device
10.0 on pci0
amr0: <LSILogic CERC ATA100/4ch> Firmware H661, BIOS 1.01, 16MB RAM
pci0: <display, VGA> at device 11.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <ServerWorks CSB5 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x8b0-0x8bf,0x8c0-0x8c3 at device 15.1
on pci0
ata0: <ATA channel 0> on atapci1
ata1: <ATA channel 1> on atapci1
ohci0: <OHCI (generic) USB controller> mem 0xfe100000-0xfe100fff irq 3 at
device 15.2 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pcib1: <ACPI Host-PCI bridge> on acpi0
pci1: <ACPI PCI bus> on pcib1
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 drq 1
on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xcbfff,0xec000-0xeffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1130453349 Hz quality 800
Timecounters tick every 1.000 msec
acd0: CDROM <SAMSUNG CD-ROM SC-148C/B100> at ata1-master UDMA33
ad4: 381554MB <Seagate ST3400832AS 3.02> at ata2-master SATA150
ad6: 381554MB <Seagate ST3400832AS 3.02> at ata3-master SATA150
amrd0: <LSILogic MegaRAID logical drive> on amr0
amrd0: 38138MB (78106624 sectors) RAID 1 (optimal)
ar0: 381554MB <Adaptec HostRAID RAID1> status: READY
ar0: disk0 READY (master) using ad4 at ata2-master
ar0: disk1 READY (mirror) using ad6 at ata3-master
Trying to mount root from ufs:/dev/amrd0s1a
WARNING: / was not properly dismounted
WARNING: /tmp was not properly dismounted
WARNING: /usr was not properly dismounted
WARNING: /var was not properly dismounted
_______________________________________________
freebsd...@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "freebsd-stabl...@freebsd.org"
Filip Wuytack
I also tried to create the label via the command line (following the
handbook).
web2# dd if=/dev/zero of=/dev/ar0 count=2
2+0 records in
2+0 records out
1024 bytes transferred in 0.000757 secs (1352746 bytes/sec)
web2# disklabel /dev/ar0 | disklabel -B -R -r ar0 /dev/stdin
disklabel: /dev/ar0: no valid label found
And the system freezes and shows 'ata2: DISCONNECT requested'
Any help would be appreciated.
Thanks,
Filip
:-----Original Message-----
:From: owner-free...@freebsd.org
:[mailto:owner-free...@freebsd.org] On Behalf Of Filip Wuytack
:Sent: 10 November 2005 11:45
:To: freebsd...@freebsd.org
:Subject: Adaptec SATA 1210SA+ Freebsd 6.0
:
:Hi,
:
:I just installed freebsd 6 and it all runs fine, but when I try (via
:sysinstall) to make a new label on a partition on ar0, the system says:
:'ata2 disconnect requested' and freezes. I there something
:extra I need to
:do make ar0 to work properly?
:
:Many thanks,
:
:Filip
:
:This is the output of my dmesg.boot:
:=============================================
:
:Copyright (c) 1992-2005 The FreeBSD Project.
:Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992,
:1993, 1994
: The Regents of the University of California. All rights
:reserved.
:FreeBSD 6.0-RELEASE #0: Thu Nov 3 09:36:13 UTC 2005
: ro...@x64.samsco.home:/usr/obj/usr/src/sys/GENERIC
:ACPI APIC Table: <DELL PE500SC >
:Timecounter "i8254" frequency 1193182 Hz quality 0
:CPU: Intel(R) Pentium(R) III CPU family 1133MHz
:(1130.45-MHz 686-class
:CPU)
: Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
:
:Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,
:MTRR,PGE,MCA,
:CMOV,PAT,PSE36,MMX,FXSR,SSE>
:0xecb8-0xecbf,0xecb0-0xecb3,0xeca0-0xeca7,0xec98-0xec9b,0xec80-
:0xec8f mem
:
Doug White
> Hi,
>
> I also tried to create the label via the command line (following the
> handbook).
>
> web2# dd if=/dev/zero of=/dev/ar0 count=2
> 2+0 records in
> 2+0 records out
> 1024 bytes transferred in 0.000757 secs (1352746 bytes/sec)
> web2# disklabel /dev/ar0 | disklabel -B -R -r ar0 /dev/stdin
> disklabel: /dev/ar0: no valid label found
>
> And the system freezes and shows 'ata2: DISCONNECT requested'
I'd take a first guess that the disk attached to ata2 is having issues.
Reseat and perhaps replace the cables. If that doesn't work then download
and run the manufacturer's diagnostic tool and see if you can get that to
error out.
--
Doug White | FreeBSD: The Power to Serve
dwh...@gumbysoft.com | www.FreeBSD.org