6.1 hardware issues
workd...@yahoo.ca
problem is however a little beyond me.
Essentially I was given an Intergraph workstation. (TDZ2000 GT1)
Simply a dual 700Mhz PIII that has a Symbios 53C896 and a Symbios
53C860 built in.
FBSD 4.9 (generic) can see the hardware (896), and yet FBSD 6.1
(generic) can't. I've been poking around with this for ages, and I
can't get it.. Thus I'm asking for help!
On the 6.1 dmesg, it appears that the computer misses a host PCI
bridge.. somehow skipping from pcib1 to pcib3.. Which I think is odd.
And of course, that's the same bus that the 896 is on..
Thus I have 6.1 up and running on a 2GB scsi HD, (from the 860) however
I would like to use the 896 since it's faster and I actually have HD's
with reasonable sizes on there. ;) (FBSD4.9 is installed and running
from the 896 controller, however without SMP.)
So, I'm looking to see if anyone has any insights, help, or simply
guesses! Pardon the long post.
6.1 dmesg (-v)
++++++++++++++++++++++++++++++++++++++++
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993,
1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-RELEASE #0: Sun May 7 04:42:56 UTC 2006
ro...@opus.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP
MPTable: <INGR TDZ2000 GT1 >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Pentium III (695.33-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x681 Stepping = 1
Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory = 536870912 (512 MB)
avail memory = 515846144 (491 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 1
cpu1 (AP): APIC ID: 0
ioapic0: Assuming intbase of 0
ioapic1: Assuming intbase of 16
ioapic0 <Version 1.1> irqs 0-15 on motherboard
ioapic1 <Version 1.1> irqs 16-31 on motherboard
kbd1 at kbdmux0
cpu0 on motherboard
cpu1 on motherboard
pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 0.1 on pci0
pci1: <PCI bus> on pcib1
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xfc00-0xfc7f mem
0xfebef800-0xfebef87f irq 23 at device 1.0 on pci0
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: Ethernet address: 08:00:36:04:3f:99
pci0: <multimedia, audio> at device 3.0 (no driver attached)
pci0: <display, VGA> at device 12.0 (no driver attached)
pci0: <multimedia, audio> at device 14.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
pcib3: <MPTable Host-PCI bridge> pcibus 3 on motherboard
pci3: <PCI bus> on pcib3
sym0: <860> port 0xe400-0xe4ff mem 0xdffdf800-0xdffdf8ff irq 29 at
device 2.0 on pci3
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym0: open drain IRQ line driver
sym0: using LOAD/STORE-based firmware.
sym0: SCAN FOR LUNS disabled for targets 0 1 2 3 4 5 6.
sym0: [GIANT-LOCKED]
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcb7ff on
isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model MouseMan+, device ID 0
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq
2 on isa0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0200> can't assign resources (port)
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0400> can't assign resources (port)
Timecounters tick every 1.000 msec
Waiting 5 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
SMP: AP CPU #1 Launched!
da0 at sym0 bus 0 target 4 lun 0
da0: <COMPAQPC ST32155N 0564> Fixed Direct Access SCSI-2 device
da0: 20.000MB/s transfers (20.000MHz, offset 8), Tagged Queueing
Enabled
da0: 2006MB (4110000 512 byte sectors: 255H 63S/T 255C)
cd0 at sym0 bus 0 target 2 lun 0
cd0: < CD-R/RW RW7060S 1.80> Removable CD-ROM SCSI-2 device
cd0: 8.064MB/s transfers (8.064MHz, offset 8)
cd0: cd present [294118 x 2048 byte records]
Trying to mount root from ufs:/dev/da0s1a
4.9 dmesg (-v)
++++++++++++++++++++++++++++++++++++++++++
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988,
1989, 1991, 1992, 1993, 1994
The Regents of the University of California.
All rights reserved.
FreeBSD 4.9-RELEASE #0: Mon Oct 27 17:51:09 GMT 2003
ro...@freebsd-stable.sentex.ca:/usr/obj/usr/src/sys/GENERIC
Calibrating clock(s) ... TSC clock: 695339753
Hz, i8254 clock: 1193204 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Intel Pentium III (695.33-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x681 Stepping = 1
Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory = 536870912 (524288K bytes)
Physical memory chunk(s):
0x000001000 - 0x00009dfff, 643072 bytes (157 pages)
0x000566000 - 0x01fff7fff, 531177472 bytes (129682 pages)
avail memory = 516988928 (504872K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f7460
bios32: Entry = 0xfd6c0 (c00fd6c0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x203
pnpbios: Found PnP BIOS data at 0xc00f7490
pnpbios: Entry = f0000:a066 Rev = 1.0
Other BIOS signatures found:
ACPI: 00000000
Preloaded elf kernel "kernel" at 0xc053f000.
Pentium Pro MTRR support enabled
Creating DISK md0
md0: Malloc disk
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x80008870
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000]
[hdr=80] is there (id=00071166)
Using $PIR table, 15 entries at 0xc00fde60
pcib-: pcib0 exists, using next available unit number
pcib-: pcib0 exists, using next available unit number
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x1166, dev=0x0007, revid=0x04
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base e0000000, size 28
map[14]: type 1, range 32, base febee000, size 12
found-> vendor=0x1166, dev=0x0005, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=1
subordinatebus=1 secondarybus=1
found-> vendor=0x10b7, dev=0x9055, revid=0x24
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base 0000fc00, size 7
map[14]: type 1, range 32, base febef800, size 7
found-> vendor=0x1274, dev=0x1371, revid=0x02
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000fcc0, size 6
found-> vendor=0x121a, dev=0x0005, revid=0x01
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base fc000000, size 25
map[14]: type 1, range 32, base f8000000, size 25
map[18]: type 1, range 32, base 0000f800, size 8
found-> vendor=0x1220, dev=0x4242, revid=0x02
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000f440, size 6
map[14]: type 1, range 32, base fe400000, size 22
map[18]: type 1, range 32, base 0000f480, size 7
map[1c]: type 1, range 32, base 0000fca0, size 5
found-> vendor=0x1166, dev=0x0200, revid=0x4d
class=06-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0007, revid=0x04
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base 00000000, size 0
found-> vendor=0x1166, dev=0x0005, revid=0x02
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
pci0: <PCI bus> on pcib0
pcib4: <PCI to PCI bridge (vendor=1166 device=0005)> at device 0.1 on
pci0
pci1: <PCI bus> on pcib4
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xfc00-0xfc7f mem
0xfebef800-0xfebef87f irq 5 at device 1.0 on pci0
xl0: using port I/O
xl0: Ethernet address: 08:00:36:04:3f:99
xl0: media options word: a
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: xl0 attached
pci0: <unknown card> (vendor=0x1274, dev=0x1371) at 3.0 irq 10
pci0: <3Dfx Voodoo 3 graphics accelerator> (vendor=0x121a, dev=0x0005)
at 12.0 irq 10
pci0: <unknown card> (vendor=0x1220, dev=0x4242) at 14.0 irq 10
isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
pci-: pci1 exists, using next available unit number
pcib1: <ServerWorks NB6536 2.0HE host to PCI bridge> on motherboard
found-> vendor=0x1000, dev=0x000b, revid=0x01
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000f000, size 8
map[14]: type 1, range 64, base dffef800, size 10
map[1c]: type 1, range 64, base dffec000, size 13
found-> vendor=0x1000, dev=0x000b, revid=0x01
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=10
map[10]: type 1, range 32, base 0000e800, size 8
map[14]: type 1, range 64, base dffef400, size 10
map[1c]: type 1, range 64, base dffea000, size 13
pci2: <PCI bus> on pcib1
sym0: <896> port 0xf000-0xf0ff mem
0xdffec000-0xdffedfff,0xdffef800-0xdffefbff irq 10 at device 1.0 on
pci2
sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: handling phase mismatch from SCRIPTS.
sym0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 07/4e/a0/01/00/24
sym0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 07/4e/80/01/08/24
sym0: SCAN FOR LUNS disabled for targets 0 1.
sym0: Delay (GEN=11): 234 msec, 37984 KHz
sym0: Delay (GEN=11): 264 msec, 33667 KHz
sym0: Delay (GEN=11): 265 msec, 33540 KHz
sym0: enabling clock multiplier
sym0: Downloading SCSI SCRIPTS.
sym1: <896> port 0xe800-0xe8ff mem
0xdffea000-0xdffebfff,0xdffef400-0xdffef7ff irq 10 at device 1.1 on
pci2
sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym1: handling phase mismatch from SCRIPTS.
sym1: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 07/4e/a0/01/00/24
sym1: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 07/4e/80/01/08/24
sym1: Delay (GEN=11): 234 msec, 37984 KHz
sym1: Delay (GEN=11): 264 msec, 33667 KHz
sym1: Delay (GEN=11): 265 msec, 33540 KHz
using shared irq10.
sym1: enabling clock multiplier
sym1: Downloading SCSI SCRIPTS.
pci-: pci2 exists, using next available unit number
pcib2: <Host to PCI bridge> on motherboard
found-> vendor=0x1000, dev=0x0006, revid=0x13
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000e400, size 8
map[14]: type 1, range 32, base dffdf800, size 8
pci3: <PCI bus> on pcib2
sym2: <860> port 0xe400-0xe4ff mem 0xdffdf800-0xdffdf8ff irq 10 at
device 2.0 on pci3
sym2: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym2: open drain IRQ line driver
sym2: using LOAD/STORE-based firmware.
sym2: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/ce/a0/01/00/00
sym2: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/ce/a0/01/08/00
sym2: SCAN FOR LUNS disabled for targets 0 1 2 3 4 5 6.
sym2: Delay (GEN=11): 236 msec, 37662 KHz
sym2: Delay (GEN=11): 264 msec, 33667 KHz
sym2: Delay (GEN=11): 265 msec, 33540 KHz
pci-: pci3 exists, using next available unit number
pcib3: <ServerWorks NB6536 2.0HE host to PCI bridge> on motherboard
pci4: <PCI bus> on pcib3
ex_isa_identify()
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcb7ff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x0000
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
adv0 failed to probe on isa0
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 failed to probe at port 0x134-0x137 on isa0
aha0: status reg test failed ff
Aug 11 01:42:17 TDZ2KGT1 last message repeated 5 times
aha0 failed to probe at port 0x134-0x137 on isa0
aic0 failed to probe at port 0x140-0x15f on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model MouseMan+, device ID 0-4c, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:08, syncbits:08
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
sn0: not probed (disabled)
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fffe3f 0..1023=1024 cylinders, 0..254=255
heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 68c040, tty 63109a, net 6710ba
bpf: sl0 attached
bpf: faith0 attached
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
sym0: enabling clock multiplier
sym0: Downloading SCSI SCRIPTS.
(noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
sym1: enabling clock multiplier
sym1: Downloading SCSI SCRIPTS.
(noperiph:sym2:0:-1:-1): SCSI BUS reset delivered.
Creating DISK da0
Creating DISK cd0
pass0 at sym1 bus 0 target 0 lun 0
pass0: <SEAGATE ST39102LW 0006> Fixed Direct Access SCSI-2 device
pass0: Serial Number LJB723570000192615NW
pass0: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged
Queueing Enabled
pass1 at sym2 bus 0 target 2 lun 0
pass1: < CD-R/RW RW7060S 1.80> Removable CD-ROM SCSI-2 device
pass1: Serial Number [
pass1: 8.064MB/s transfers (8.064MHz, offset 8)
da0 at sym1 bus 0 target 0 lun 0
da0: <SEAGATE ST39102LW 0006> Fixed Direct Access SCSI-2 device
da0: Serial Number LJB723570000192615NW
da0: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged
Queueing Enabled
da0: 8683MB (17783240 512 byte sectors: 255H 63S/T 1106C)
cd0 at sym2 bus 0 target 2 lun 0
cd0: < CD-R/RW RW7060S 1.80> Removable CD-ROM SCSI-2 device
cd0: Serial Number [
cd0: 8.064MB/s transfers (8.064MHz, offset 8)
cd0: cd present [294118 x 2048 byte records]
Mounting root from ufs:/dev/da0s3a
da0s1: type 0x6, start 63, end = 4192964, size 4192902 : OK
da0s2: type 0x7, start 4192965, end = 10329794, size 6136830 : OK
da0s3: type 0xa5, start 10329795, end = 17751824, size 7422030 : OK
start_init: trying /sbin/init
++++++++++++++++++++++++++++++++++++++
MP Table:
===============================================================================
MPTable, version 2.0.15
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000f7440
signature: '_MP_'
length: 16 bytes
version: 1.4
checksum: 0x56
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x0009e160
signature: 'PCMP'
base table length: 340
version: 1.4
checksum: 0x41
OEM ID: 'INGR '
Product ID: 'TDZ2000 GT1 '
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 34
local APIC address: 0xfee00000
extended table length: 308
extended table checksum: 13
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step
Flags
1 0x11 BSP, usable 6 8 1
0x387fbff
0 0x11 AP, usable 6 8 1
0x387fbff
--
Bus: Bus ID Type
0 PCI
1 PCI
2 PCI
3 PCI
4 ISA
--
I/O APICs: APIC ID Version State Address
2 0x11 usable 0xfec00000
3 0x11 usable 0xfec01000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID
PIN#
ExtINT active-hi edge 4 0 2
0
INT active-hi edge 4 1 2
1
INT active-hi edge 4 0 2
2
INT active-hi edge 4 3 2
3
INT active-hi edge 4 4 2
4
INT active-lo edge 4 5 2
5
INT active-hi edge 4 6 2
6
INT active-hi edge 4 7 2
7
INT active-hi edge 4 8 2
8
INT active-hi edge 4 9 2
9
INT active-lo edge 4 10 2
10
INT active-hi edge 4 11 2
11
INT active-hi edge 4 12 2
12
INT active-hi edge 4 13 2
13
INT active-hi edge 4 14 2
14
INT active-hi edge 4 15 2
15
INT active-lo level 0 1:A 3
7
INT active-lo level 0 3:A 3
14
INT active-lo level 0 12:A 3
4
INT active-lo level 0 14:A 3
6
INT active-lo level 2 1:A 3
10
INT active-lo level 2 1:B 3
11
INT active-lo level 3 2:A 3
13
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID
PIN#
ExtINT active-hi edge 4 0 255
0
NMI active-hi edge 0 0:A 255
1
-------------------------------------------------------------------------------
MP Config Extended Table Entries:
--
System Address Space
bus ID: 0 address type: I/O address
address base: 0x0
address range: 0xe400
--
System Address Space
bus ID: 3 address type: I/O address
address base: 0xe400
address range: 0x100
--
System Address Space
bus ID: 0 address type: I/O address
address base: 0xe500
address range: 0x300
--
System Address Space
bus ID: 2 address type: I/O address
address base: 0xe800
address range: 0x900
--
System Address Space
bus ID: 0 address type: I/O address
address base: 0xf100
address range: 0xf00
--
System Address Space
bus ID: 0 address type: memory address
address base: 0x20000000
address range: 0xbffd0000
--
System Address Space
bus ID: 3 address type: memory address
address base: 0xdffd0000
address range: 0x10000
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xdffe0000
address range: 0x0
--
System Address Space
bus ID: 2 address type: memory address
address base: 0xdffe0000
address range: 0x10000
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xdfff0000
address range: 0x10000
--
System Address Space
bus ID: 0 address type: prefetch address
address base: 0xe0000000
address range: 0x1a000000
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xfa000000
address range: 0x4e00000
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xfee01000
address range: 0x11ff000
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xa0000
address range: 0x20000
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xcc000
address range: 0x10000
--
Bus Heirarchy
bus ID: 4 bus info: 0x01 parent bus ID: 0
===============================================================================
4.9 ScanPCI (-v)
pci bus 0x0000 cardnum 0x00 function 0x00: vendor 0x1166 device 0x0007
ServerWorks CNB20-LE Host Bridge
STATUS 0x2200 COMMAND 0x0106
CLASS 0x06 0x00 0x00 REVISION 0x04
BIST 0x00 HEADER 0x80 LATENCY 0x40 CACHE 0x08
BASE0 0xe0000008 addr 0xe0000000 MEM PREFETCHABLE
BASE1 0xfebee000 addr 0xfebee000 MEM
pci bus 0x0000 cardnum 0x00 function 0x01: vendor 0x1166 device 0x0005
ServerWorks CNB20-LE Host Bridge
STATUS 0x22b0 COMMAND 0x0007
CLASS 0x06 0x04 0x00 REVISION 0x02
HEADER 0x81 LATENCY 0x40
PRIBUS 0x00 SECBUS 0x01 SUBBUS 0x01
SECLT 0x40 SECSTATUS 0x22a0
IOBASE 0xf000 IOLIM 0x0fff
NOPREFETCH_MEMBASE 0xfff00000 MEMLIM 0x000fffff
PREFETCH_MEMBASE 0xfff00000 MEMLIM 0x000fffff
NO_FAST_B2B NO_SEC_BUS_RST NO_M_ABRT NO_VGA_EN NO_ISA_EN NO_SERR_EN
NO_PERR_EN
pci bus 0x0000 cardnum 0x01 function 0x00: vendor 0x10b7 device 0x9055
3Com Corporation 3c905B 100BaseTX [Cyclone]
CardVendor 0x1091 card 0x9055 (Intergraph Corporation, Card unknown)
STATUS 0x0210 COMMAND 0x0017
CLASS 0x02 0x00 0x00 REVISION 0x24
BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x08
BASE0 0x0000fc01 addr 0x0000fc00 I/O
BASE1 0xfebef800 addr 0xfebef800 MEM
MAX_LAT 0x0a MIN_GNT 0x0a INT_PIN 0x01 INT_LINE 0x0a
pci bus 0x0000 cardnum 0x03 function 0x00: vendor 0x1274 device 0x1371
Ensoniq ES1371 [AudioPCI-97]
STATUS 0x0410 COMMAND 0x0005
CLASS 0x04 0x01 0x00 REVISION 0x02
BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x00
BASE0 0x0000fcc1 addr 0x0000fcc0 I/O
MAX_LAT 0x80 MIN_GNT 0x0c INT_PIN 0x01 INT_LINE 0x0a
pci bus 0x0000 cardnum 0x0c function 0x00: vendor 0x121a device 0x0005
3Dfx Interactive, Inc. Voodoo 3
CardVendor 0x121a card 0x0036 (3Dfx Interactive, Inc. Voodoo3)
STATUS 0x8090 COMMAND 0x0003
CLASS 0x03 0x00 0x00 REVISION 0x01
BIST 0x00 HEADER 0x00 LATENCY 0x00 CACHE 0x00
BASE0 0xfc000000 addr 0xfc000000 MEM
BASE1 0xf8000008 addr 0xf8000000 MEM PREFETCHABLE
BASE2 0x0000f801 addr 0x0000f800 I/O
MAX_LAT 0x00 MIN_GNT 0x00 INT_PIN 0x01 INT_LINE 0x07
BYTE_0 0x01 BYTE_1 0x00 BYTE_2 0x00 BYTE_3 0x00
pci bus 0x0000 cardnum 0x0e function 0x00: vendor 0x1220 device 0x4242
Ariel Corporation Device unknown
STATUS 0x0000 COMMAND 0x0007
CLASS 0x04 0x01 0x00 REVISION 0x02
BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x00
BASE0 0x0000f441 addr 0x0000f440 I/O
BASE1 0xfe400000 addr 0xfe400000 MEM
BASE2 0x0000f481 addr 0x0000f480 I/O
BASE3 0x0000fca1 addr 0x0000fca0 I/O
MAX_LAT 0x03 MIN_GNT 0x0f INT_PIN 0x01 INT_LINE 0x0a
BYTE_0 0xff BYTE_1 0xff BYTE_2 0xff BYTE_3 0xff
pci bus 0x0000 cardnum 0x0f function 0x00: vendor 0x1166 device 0x0200
ServerWorks OSB4 South Bridge
STATUS 0x0200 COMMAND 0x0007
CLASS 0x06 0x01 0x00 REVISION 0x4d
BIST 0x00 HEADER 0x00 LATENCY 0x00 CACHE 0x00
BYTE_0 0xf0 BYTE_1 0x33 BYTE_2 0x00 BYTE_3 0x00
pci bus 0x0000 cardnum 0x11 function 0x00: vendor 0x1166 device 0x0007
ServerWorks CNB20-LE Host Bridge
STATUS 0x6200 COMMAND 0x0106
CLASS 0x06 0x00 0x00 REVISION 0x04
BIST 0x00 HEADER 0x80 LATENCY 0x30 CACHE 0x08
BASE0 0x00000008 addr 0x00000000 MEM PREFETCHABLE
pci bus 0x0000 cardnum 0x11 function 0x01: vendor 0x1166 device 0x0005
ServerWorks CNB20-LE Host Bridge
STATUS 0x2200 COMMAND 0x0107
CLASS 0x06 0x00 0x00 REVISION 0x02
BIST 0x00 HEADER 0x80 LATENCY 0x30 CACHE 0x08
pci bus 0x0002 cardnum 0x01 function 0x00: vendor 0x1000 device 0x000b
LSI Logic / Symbios Logic 53c896
STATUS 0x0210 COMMAND 0x0057
CLASS 0x01 0x00 0x00 REVISION 0x01
BIST 0x00 HEADER 0x80 LATENCY 0x48 CACHE 0x08
BASE0 0x0000f001 addr 0x0000f000 I/O
BASE1 0x00000000dffef804 addr 0x00000000dffef800 MEM 64BIT
BASE3 0x00000000dffec004 addr 0x00000000dffec000 MEM 64BIT
MAX_LAT 0x40 MIN_GNT 0x11 INT_PIN 0x01 INT_LINE 0x0a
BYTE_0 0x01 BYTE_1 0x00 BYTE_2 0x01 BYTE_3 0x06
pci bus 0x0002 cardnum 0x01 function 0x01: vendor 0x1000 device 0x000b
LSI Logic / Symbios Logic 53c896
STATUS 0x0210 COMMAND 0x0057
CLASS 0x01 0x00 0x00 REVISION 0x01
BIST 0x00 HEADER 0x80 LATENCY 0x48 CACHE 0x08
BASE0 0x0000e801 addr 0x0000e800 I/O
BASE1 0x00000000dffef404 addr 0x00000000dffef400 MEM 64BIT
BASE3 0x00000000dffea004 addr 0x00000000dffea000 MEM 64BIT
MAX_LAT 0x40 MIN_GNT 0x11 INT_PIN 0x02 INT_LINE 0x0a
BYTE_0 0x01 BYTE_1 0x00 BYTE_2 0x01 BYTE_3 0x06
pci bus 0x0003 cardnum 0x02 function 0x00: vendor 0x1000 device 0x0006
LSI Logic / Symbios Logic 53c860
CardVendor 0x1000 card 0x1000 (LSI Logic / Symbios Logic, Card
unknown)
STATUS 0x0210 COMMAND 0x0057
CLASS 0x01 0x00 0x00 REVISION 0x13
BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x08
BASE0 0x0000e401 addr 0x0000e400 I/O
BASE1 0xdffdf800 addr 0xdffdf800 MEM
MAX_LAT 0x40 MIN_GNT 0x08 INT_PIN 0x01 INT_LINE 0x0a
BYTE_0 0x01 BYTE_1 0x00 BYTE_2 0x01 BYTE_3 0x00
"james <at> hal-pc.org"
> FBSD 4.9 (generic) can see the hardware (896), and yet FBSD 6.1
> (generic) can't. I've been poking around with this for ages, and I
> can't get it.. Thus I'm asking for help!
i have an LSI (fka: SymBIOS) 876 and 2 810's working in 5.4
what does "pciconf -vl" show? curious.
without getting too crazy hacking together pieces of 4.x to get it to
work, i'd try the suggestion in the man page on using a kernel option to
attach a different driver to it (ncr).
ie. add:
options SYM_SETUP_LP_PROBE_MAP=0x04
to your kernel config and recompile.
see "man sym"
for the option to be there in the first place it's probably a known
issue with some cards/revisions.
workd...@yahoo.ca
Currently 4.11 sees the bridge (and anything on pci2), and thus the
896. 5.0 doesn't. That is a lot of changes with regards to the two
different versions!
--
james <at> hal-pc.org wrote:
> i have an LSI (fka: SymBIOS) 876 and 2 810's working in 5.4
> what does "pciconf -vl" show? curious.
(I knew there was some inforomation I was forgetting..)
Under 6.1GR pciconf -lv displays..
hostb0@pci0:0:0: class=0x060000 card=0x00000000 chip=0x00071166
rev=0x04 hdr=0x00
vendor = 'ServerWorks (Was: Reliance Computer Corp)'
device = 'NB6635 (CNB20-LE/HE) CPU to PCI Bridge'
class = bridge
subclass = HOST-PCI
pcib1@pci0:0:1: class=0x060400 card=0x00000080 chip=0x00051166 rev=0x02
hdr=0x01
vendor = 'ServerWorks (Was: Reliance Computer Corp)'
device = 'NB6536 (CNB20-LE) PCI to PCI Bridge, bus/dev/func
0/0/1'
class = bridge
subclass = PCI-PCI
xl0@pci0:1:0: class=0x020000 card=0x90551091 chip=0x905510b7 rev=0x24
hdr=0x00
vendor = '3COM Corp, Networking Division'
device = '3C905B-TX Fast Etherlink 10/100 PCI TX NIC'
class = network
subclass = ethernet
none0@pci0:3:0: class=0x040100 card=0x13711274 chip=0x13711274 rev=0x02
hdr=0x00
vendor = 'Creative (Was: Ensoniq)'
device = 'ES1371, ES1373 AudioPCI'
class = multimedia
subclass = audio
none1@pci0:12:0: class=0x030000 card=0x0036121a chip=0x0005121a
rev=0x01 hdr=0x00
vendor = '3dfx Interactive Inc'
device = 'Voodoo3 All Voodoo3 chips, 3000'
class = display
subclass = VGA
none2@pci0:14:0: class=0x040100 card=0x00000000 chip=0x42421220
rev=0x02 hdr=0x00
vendor = 'Ariel Corporation'
class = multimedia
subclass = audio
isab0@pci0:15:0: class=0x060100 card=0x02001166 chip=0x02001166
rev=0x4d hdr=0x00
vendor = 'ServerWorks (Was: Reliance Computer Corp)'
device = 'OSB4 PCI to ISA Bridge'
class = bridge
subclass = PCI-ISA
hostb1@pci0:17:0: class=0x060000 card=0x00000000 chip=0x00071166
rev=0x04 hdr=0x00
vendor = 'ServerWorks (Was: Reliance Computer Corp)'
device = 'NB6635 (CNB20-LE/HE) CPU to PCI Bridge'
class = bridge
subclass = HOST-PCI
hostb2@pci0:17:1: class=0x060000 card=0x00000000 chip=0x00051166
rev=0x02 hdr=0x00
vendor = 'ServerWorks (Was: Reliance Computer Corp)'
device = 'NB6536 (CNB20-LE) PCI to PCI Bridge, bus/dev/func
0/0/1'
class = bridge
subclass = HOST-PCI
sym0@pci3:2:0: class=0x010000 card=0x10001000 chip=0x00061000 rev=0x13
hdr=0x00
vendor = 'LSI Logic (Was: Symbios Logic, NCR)'
device = 'LSI53C860/860E PCI to Ultra SCSI I/O Processor'
class = mass storage
subclass = SCSI
================
scanpci sees the cards however...
pci bus 0x0000 cardnum 0x00 function 0x00: vendor 0x1166 device 0x0007
Broadcom CNB20-LE Host Bridge
pci bus 0x0000 cardnum 0x00 function 0x01: vendor 0x1166 device 0x0005
Broadcom CNB20-LE Host Bridge
pci bus 0x0000 cardnum 0x01 function 0x00: vendor 0x10b7 device 0x9055
3Com Corporation 3c905B 100BaseTX [Cyclone]
pci bus 0x0000 cardnum 0x03 function 0x00: vendor 0x1274 device 0x1371
Ensoniq ES1371 [AudioPCI-97]
pci bus 0x0000 cardnum 0x0c function 0x00: vendor 0x121a device 0x0005
3Dfx Interactive, Inc. Voodoo 3
pci bus 0x0000 cardnum 0x0e function 0x00: vendor 0x1220 device 0x4242
Ariel Corporation Device unknown
pci bus 0x0000 cardnum 0x0f function 0x00: vendor 0x1166 device 0x0200
Broadcom OSB4 South Bridge
pci bus 0x0000 cardnum 0x11 function 0x00: vendor 0x1166 device 0x0007
Broadcom CNB20-LE Host Bridge
pci bus 0x0000 cardnum 0x11 function 0x01: vendor 0x1166 device 0x0005
Broadcom CNB20-LE Host Bridge
pci bus 0x0002 cardnum 0x01 function 0x00: vendor 0x1000 device 0x000b
LSI Logic / Symbios Logic 53C896/897
pci bus 0x0002 cardnum 0x01 function 0x01: vendor 0x1000 device 0x000b
LSI Logic / Symbios Logic 53C896/897
pci bus 0x0003 cardnum 0x02 function 0x00: vendor 0x1000 device 0x0006
LSI Logic / Symbios Logic 53c860
=======================
>
> without getting too crazy hacking together pieces of 4.x to get it to
> work,
Yep, I'm not really a fan of this plan. My coding skils are not *that*
good. ;)
> i'd try the suggestion in the man page on using a kernel option to
> attach a different driver to it (ncr).
> ie. add:
> options SYM_SETUP_LP_PROBE_MAP=0x04
> to your kernel config and recompile.
Is there anyway to set this as a boot variable? With a 2GB drive,
space is kinda tight for a whole source tree. (More storage is an
option, however...)
> see "man sym"
>
> for the option to be there in the first place it's probably a known
> issue with some cards/revisions.
I had a look at the man page of sym, yet it's odd that I don't see
anything for or about PCI 2 in the dmesgs.. I recently put in a qlogic
2200, and again, on FBSD 4.9 it sees the card (on PCI2), and 6.1
doesn't see that bus. I think there's something up with regards to the
CPU - PCI and PCI - PCI bridges. (For this machine at the least.)
:/
Once I get some more storage, I can install the source tree and
_attempt_ (whole new can of worms!) to make buildkernel with the
SYM_SETUP_LP_PROBE_MAP=0x04 option.
"james <at> hal-pc.org"
>> ie. add:
>> options SYM_SETUP_LP_PROBE_MAP=0x04
>> to your kernel config and recompile.
>
> Is there anyway to set this as a boot variable? With a 2GB drive,
> space is kinda tight for a whole source tree. (More storage is an
> option, however...)
no. not that i know of at least.
/usr/src--> du -d1 -h
<snip>
104M ./sys
<snip>
i hope you have 150 megs or so free. it's not /that/ big for a base
install. sys is all you need anyway for just the kernel.
untar the ssys.?? from the CD by mounting the cd and:
cat /cdrom/6.1-RELEASE/src/ssys.?? | tar --unlink -xpzfv - -C /usr/src
alt:
use cvsup (/usr/ports/net/cvsup-without-gui) for a more current tree.
in particular /usr/share/example/cvsup/standard-supfile
change the CHANGE_THIS.freebsd.org to cvsup#.freebsd.org where #=a
number (ie 3 or 4 or 5 etc.). it doesn't much matter.
then just comment out all but sys from the sources to fetch and run
cvsup as the examples show. if you're very limited on space like you
say then option one may be best (to test with at least).
see the handbook for kernel config and compile instructions.
>> see "man sym"
>>
>> for the option to be there in the first place it's probably a known
>> issue with some cards/revisions.
>
> I had a look at the man page of sym, yet it's odd that I don't see
> anything for or about PCI 2 in the dmesgs.. I recently put in a qlogic
> 2200, and again, on FBSD 4.9 it sees the card (on PCI2), and 6.1
> doesn't see that bus. I think there's something up with regards to the
> CPU - PCI and PCI - PCI bridges. (For this machine at the least.)
move the "non-working" one to a different slot maybe?
i doubt that'll help though.
> Once I get some more storage, I can install the source tree and
> _attempt_ (whole new can of worms!) to make buildkernel with the
> SYM_SETUP_LP_PROBE_MAP=0x04 option.
good luck. let us know if you get it working.
workd...@yahoo.ca
james <at> hal-pc.org wrote:
> move the "non-working" one to a different slot maybe?
> i doubt that'll help though.
*sweet* I dropped the QLogic card to the bottom pci slot, and it shows
up on pci3! *so* much more room to move around! (1Gb/sec fibre, 8 x
18GB drive array, not mine, but not currently in use.. so anyhoo..)
Weee...
As for the 896, (and the 890) they're on the mobo.. No moving them
around too much. :)
Thanks for the device hint ;) and your time.
~M.
--
sp...@controlq.com
On Wed, 23 Aug 2006, it was written:
> Date: Wed, 23 Aug 2006 00:14:33 -0500
> From: "james <at> hal-pc.org"
> Newsgroups: comp.unix.bsd.freebsd.misc
> Subject: Re: 6.1 hardware issues
I seem to have a very similar problem with the Micron 6200, but cannot
seem to get past the install boot (2ndary). Can you drop into the boot
loader and set a hint or kernel variable to force the probe map?? I'm not
far enough along to be able to config/recompile the kernel on the target
box ... as the install fails ...
workd...@yahoo.ca
james <at> hal-pc.org wrote:
> workd...@yahoo.ca wrote:
> >> ie. add:
> >> options SYM_SETUP_LP_PROBE_MAP=0x04
> >> to your kernel config and recompile.
Well, compiling the kernel went well, and the ncr device is loaded into
memory, and the flag was set, however there's no ncr device. I'm quite
certain that the bridge is what is being missed. I started a new
thread in this group with regards to that (the missing bridge).
Thank-you for your time and suggestion(s).
~M.
--