I first noticed this about 10 days ago when the print quality on my Pixma
declined. I opened 'er up and saw that the black tank was completely
drained, but I'd received no warning from either the status monitor or the
printer itself. I had a quick shufty at the ink levels in the status monitor
and it was showing that the black was still roughly half full (even though
it was obvious to anyone looking at the tank itself it was completely
empty). I popped in a replacement, but the printer didn't go through a
charge cycle, so I ran a cleaning cycle in the hope that it might update the
status - it didn't. I then compared the other SM levels with the actual
amount of ink remaining in the other tanks - and noticed that it was
misreporting every single colour (and it's indiscriminate about how it
reports - e.g. it's informing me that the red and green are practically full
when, in reality, they're both two-thirds empty, it's telling me that the
yellow is nearly gone when, in fact, there's more than half a tank left).
I then, just for the sheer hell of it, decided to do a manual head
alignment. This is where I noticed the next problem - each bar in the 'K'
column (I believe that's the bi-directional one) is equally flawed - i.e. I
cannot select the best one because there isn't a best one!
I spoke to Canon (and got put through to India - literally!) and, obviously,
had real problems making myself understood (I think they're just trained to
tell people to reinstall the driver and that's the sum total of their
English). I was then called back by a tier two rep who spoke English but was
just about as clueless as the tier one droid. He wants me to return the
printer, at my expense, for them to have sitting on a shelf somewhere for 10
working days (I don't trust these repair centres as far as I can spit at
'em).
Just for laughs, I switched on the i9950, which hasn't had much use since I
bought the Pixma. It was furnished with a new set of OEMs not so long ago
and all are practically full. I checked out its status monitor and it's
telling me that each tank has 25% left - obviously erroneous. I then
performed a manual alignment and it's having identical alignment issues as
the Pixma, but not with column K; this is column E (photo cyan).
Both units are using OEM tanks. The Pixma is less than three months old.
Could someone tell me how the SM obtains its information from the printer?
Would I be correct in thinking that the little white pads under each tank
contain a sensor and that sends info to the driver? If that is the case,
would replacing the print head and reinstalling the driver help matters? I
bought a printhead (I believe that both units use an identical head) on eBay
(brand new, still sealed in its foil) for 99p because I was the only
interested party and there was no reserve.
Could anyone tell me how best to troubleshoot? Please don't tell me to go
back to Canon - I couldn't stand another 90 minutes on hold only to be put
through to some Indian who cannot string a coherent sentence together).
Both units are hooked up via high speed USB connections.
Any ideas or do I have to write off two (otherwise) perfectly working units?
The Pixma is my office printer and is in constant daily use.
Cheers m'dears!
"Miss Perspicacia Tick" <te...@test.com> wrote in message
news:rhEQe.6346$NB....@fe01.ams...
Miss Perspicacia Tick wrote:
IN THE US CANON SUPPORT IS AMERICAN.
THIS MUST HAVE SOMETHING TO DO WITH THE VISCOSITY OF THE AFTERMARKET INK.
ARE YOU USING A BRAND NAME? OOPS THERE ARE NOT BRAND NAMES.
Shooter wrote:
>Perhaps bearing in mind how you have written in the past you should consider
>changing them for Epson's or use the rude advise you have given to others.
>
>
SHE WAS NOT RUDE. SHE WAS JUST ON THE RAG. CHART HER REMARKS AND YOU
WILL UNDERSTAND.
Your complaint is the fact that your printer is not reporting proper
fullness level.
The diagram might help your understanding
http://www.steves-digicams.com/2004_reviews/canon_ip8500_pg2.html
Basicly the inktanks use a prism that when there is fluid in the tank,
the light is refracted. When the tank is empty the light is shown
though the prism and reflected back to a sensor that establishes
"empty". It's not a perfect system esp since the tanks to read full
till such time as the reservoir is well, empty, leaning you with about
20% of ink left. In theory you should beable to print as little as 2.8
full color pages 100% yield before replacing.
The only troubleshooting I can think of is contacts between the head
and the carrirage basket, whatever that thing is called, and whether or
not the area under the tanks are soiled. Beyond that I have no clue.
I accepted the fact that the ink monitor is pretty damned unreliable
even using OEM tanks with an OEM prism and manualy check my ink levels
about once a month.
"Miss Perspicacia Tick" <te...@test.com> wrote in message
news:rhEQe.6346$NB....@fe01.ams...
Thanks - and what of the more serious alignment issues? Anyone a cure for
those?
Hard to have a cure... There is an automatic printhead alignment you
can peform under maintance/self test mode, as opposed to service mode.
[note the instructions are for the ip4000, which from what I've seen
also apply to the ip8500. I don't know the equilivent in the i9900]
1) power on printer
2) press and hold the resume cancel button
3) watch das blinkin light release after X times to peform the
following maintance function
1 time Print head manual cleaning
2 times Nozzle check pattern printing Set a sheet of plain paper
(A4 or letter) in the
ASF or the cassette (according to the Paper Feed switch setting).
3 times Paper feed roller cleaning
4 times Automatic print head alignment Set a sheet of plain paper
(A4 or letter)
in the ASF.
5 times Bottom plate cleaning Fold a sheet of plain paper (A4 or
letter) in half
crosswise, then unfold and set it in the ASF with the folded ridge
facing down.
6 times or more -I don't know-
If the light blinks 11 times auto alignment failed
What what I read this could be due to Timing slit strip film QC1-4284 ,
not sure which nor do I know how to find it. I think it's the plastic
strip bit between the belt top and bottom.
QC1-4833 is the timming slit disc but that I can't even see. both
parts if soiled with grease, finger printers, or on the off chance ink
it should be cleaned/wiped with alchohol. Oddly enough excessive light
on the front of the printer might throw off auto alignment, as well as
non-white paper.
But I imagine that small alignment issues could be resolved by doing an
auto alignment followed by a manual one if need be. Otherwise this is
likely the procedure a shop would use and say it's broken if it fails.