Use of the Bifferboard to act as a wireless display for a graphics pad
	Hi there, I'm looking for a linux based solution to displaying in real time, input from a Graphics Pad (that has at least Linux 2.6.xx OS drivers) I would like to keep this as simple as possible. Using a bluetooth link would be good, recognizing that the graphics pad is a USB slave device and I want to have a 3.5" screen to display... more » By Douglas Gourlay  - May 20 - 2 new of 2 messages

	Crashes with USB 3G Modem
	I'm having a lot of troubles using a 3g module with bifferboard, even using a dedicated power source to power the 3g modem. Did you have any problem with electromagnetic interference ? I think this is the problem because if i take away the modem using an USB extension the problem is reduced.... more » By Pedro  - May 18 - 2 new of 2 messages

	Problem
	Hello, I purchased the Parallel port JTAG cable in order to upgrade the biffboot of some old biffers that I had. When I try to extract the biffboot from a new biffer the returned error is: $ ./biffjtag -d biffboot BiffJTAG v1.0: Copyright (c) Bifferos (2009), [link] Distribution prohibited, all rights reserved.... more » By Konstantinos Aravanis  - May 18 - 6 new of 6 messages

	Problems using the "new" data cable (with that switch-box) under Mac OSX Lion
	Hi All, My colleague gave me a USB/Serial cable to connect to the BB, but I can't seem to get Lion to recognize it as tty.usbserial or equivalent. I tried a Silicon Labs 201x VCP driver (as it says it is a Silicon Labs USB Data Cable) and the official Prolific 2303 driver, both do not recognize the cable.... more » By paul  - May 14 - 4 new of 4 messages

	Too much memory problem
	Hi, My Bifferboard is spending a few hours per day doing nothing, and I think that is too much wasted time. So I would like to make it work a little harder. Since it has more than 400GB of available harddisk space I thought about streaming music videos to the PS3, to watch on my TV. Why not? Right??... more » By Rilhas  - May 7 - 3 new of 3 messages

	BifferBoard with non working USB
	Hi, I've just received one BifferBoard (single USB port, 8MB flash) and when I try to connect anything on the USB port, I get the errors like these on the console when booting with any device on the bus or after plugging anything: usb 2-1: new full speed USB device using ohci_hcd and address 2... more » By Pedro Maia Alves  - May 5 - 14 new of 14 messages

	Bifferboard doesn't responding...
	Hi, yesterday I got my new bifferboard, but it isn't responding. I cannot flash it with "python bb_eth_upload.py eth0 a1:b2:c3:xx:xx:f6 mp-bb- image". Furthermore it isn't shown in my DHCP MAC list. I tried it with a FritzBox and a DD-WRT Linksys WRT54G router. What could I do? Should I resend it?... more » By Akio  - May 4 - 6 new of 6 messages

Updating OpenWRT from factory firmware

Hi All, I've having some trouble updating OpenWRT on my BB from the factory firmware to the OpenWRT version at git://github.com/bifferos/bb.g it. I am looking to connect an Arduino to my BB via USB and need some additional kernel modules (kmod-usb-serial and kmod-usb-serial-ftdi). I have downloaded the bb.git tree and used menu config to add in these... more » By blueglowey  - May 4 - 10 new of 10 messages

	Dual-USB Bifferboard SD card reader
	Hello all! Sorry my english is bad. Today arrived my Dual-USB Bifferboard. I try to use the SD card reader but I not find any information about it. At the LuCI web interface i find a "MMC/SD driver configuration" menu where there are technical questions about pinout, I not find the dual-... more » By Balajti  - May 2 - 2 new of 2 messages

	apt-get problem in Debian (sorry slightly OT)
	Running my bifferboards with Debian for a while I got a stupid problem now. I cannot successfully install new software any more with apt-get. apt-get install, .. update returns a lot of errors like that: Failed to fetch [link] 404 Not Found [IP: 130.89.148.12 80]... more » By rolf  - Apr 29 - 13 new of 13 messages