AP used as a "bridge"?

[Lloyd E. Sponenburgh]

I'm not sure I'm using the correct terminology; I may be looking for
"node" instead of "bridge".

What I'd like to do is use an inexpensive self-contained wireless device
to allow an ethernet-equipped time and attendance terminal to access (and
be accessed by) our office network. Even though the distance is only 40',
hard-wire is impossible (economically and cosmetically).

We presently have a wireless access point by which several office
computers use the LAN. I'd like the terminal to access the LAN by the AP
we already have, rather than having to create a bridge connection with
two new wireless devices.

I've configured ONE AP in the last three years (and used a wizard), so
I'm not familiar with the features of cheap WallyWorld APs like LinkSys,
etc.

Suggestions?

Thanks,
LLoyd

[ps56k]

yes - it's an Ethernet Bridge -

I use a Linksys WET11 in the family room
along with a small 5-port hub,
to link our xbox + Tivo to the Internet
via our home WiFi network.

Here's the newer version
http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1134692497433&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=9743339789B05

[Lloyd E. Sponenburgh]

"ps56k" <pschuman_...@interserv.com> fired this volley in
news:ePnSj.3311$1b7....@newssvr13.news.prodigy.net:

> http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=U
> S%2FLayout&cid=1134692497433&pagename=Linksys%2FCommon%2FVisitorWrapper
> &lid=9743339789B05

Thanks,
That was perZakly what I was looking for. For us non-wireless competent
people, it looks like a simple solution.

LLoyd

[ps56k]

if this is in the middle of a factory floor,
you might grab a WiFi laptop and go stand where the table is located
to verify you have a good WiFi signal
and there is no major or continuous RF interference
such as welders, RF heater/sealers, etc -

[Lloyd E. Sponenburgh]

"ps56k" <pschuman_...@interserv.com> fired this volley in

news:NFoSj.1115$To6...@newssvr21.news.prodigy.net:

> if this is in the middle of a factory floor,
> you might grab a WiFi laptop and go stand where the table is located
> to verify you have a good WiFi signal
> and there is no major or continuous RF interference
> such as welders, RF heater/sealers, etc -

'Tis two small buildings separated by 40' with concrete the bosses don't
want marred between, and nowhere to locate directional boring equipment.
Overhead is a no-no, too.

There are no machines except computers and an old mechanical/electrical
time clock.

I did the test your recommended before I made the post, to make sure I'd
have connectivity there.

LLoyd

[ps56k]

just to toss out another alternative - AC power or copper wire bridges.
We used these to extend our network out to the loading dock area
as we couldn't get a good signal thru the windows & metal roof/siding...
http://www.netgear.com/Products/PowerlineNetworking/PowerlineEthernetAdapters/XE102.aspx
or a Phoneline adapter.... Ethernet over a common phoneline wiring vs AC
powerline wiring

[Bill Kearney]

> I did the test your recommended before I made the post, to make sure I'd
> have connectivity there.

And you did this testing during peak times it would be in use? Interference
from industrial equipment can be a show-stopper. Same issue with powerline
gadgetry.