Google Groups no longer supports new Usenet posts or subscriptions. Historical content remains viewable.
Dismiss

Tile Overlap in Shower

7 views
Skip to first unread message

red

unread,
Jan 6, 2010, 9:57:59 PM1/6/10
to
The patient is a shower stall, acrylic base, cement backer board, 8x10
tiles in thinset. The tiles overlap the lip of the acrylic base by
1/2"(?) and there is a 1/4" gap between the bottom row of tiles and
the flat top of the base. I went to start grouting, and noticed that
the gap behind the bottom of the tiles isn't always filled with
thinset.

Is it necessary/desirable to try to push thinset/grout under the
bottom tiles and into the gap behind? Should I just squeeze extra
caulk up into the gap? Caulk seems easier, but won't support the
bottom bit of the tile as well.

Any advice appreciated.

Red

Oren

unread,
Jan 6, 2010, 10:26:45 PM1/6/10
to
On Wed, 6 Jan 2010 18:57:59 -0800 (PST), red <red...@rocketmail.com>
wrote:

What I'm reading is you have a void between the wall tile at the pan,
where they mate?

Please post a pic on a free site like tinyurl hosting....

Red Green

unread,
Jan 6, 2010, 10:29:39 PM1/6/10
to
red <red...@rocketmail.com> wrote in news:6383f0e3-8f22-4088-818c-
d7743b...@r14g2000vbc.googlegroups.com:

I'd say just caulk/grout it. There's no thinset there because the thinset
was put on the wall. That is what's holding the large tile to the
backerboard.

> but won't support the
> bottom bit of the tile as well.

Support in what way?

Jon Danniken

unread,
Jan 7, 2010, 1:16:45 AM1/7/10
to

The little bit overhanging is amply supported by the big chunk above it, and
as it isn't in a loction which receives much, if any, load, you don't need
anything behind it.

Well, you do need to caulk between the top of the tub lip and the bottom of
the CBU, but you already knew that.

Jon


nor...@earthlink.net

unread,
Jan 7, 2010, 7:51:40 AM1/7/10
to

The joint between the tile and the base should be caulked, right? One
assumes that the space not covered by thinset should be very small, so I
would not worry about it - it would take a freak accident to break it.
Normal caulking will probably fill it, and I would be inclined to do the
caulking in two stages to allow those gaps to cure comepletely before
doing the final line.

red

unread,
Jan 7, 2010, 6:45:41 PM1/7/10
to
On Jan 7, 7:51 am, "norm...@earthlink.net" <norm...@earthlink.net>
wrote:
> giant snip <

> The joint between the tile and the base should be caulked, right?  One
> assumes that the space not covered by thinset should be very small, so I
> would not worry about it - it would take a freak accident to break it.
> Normal caulking will probably fill it, and I would be inclined to do the
> caulking in two stages to allow those gaps to cure comepletely before
> doing the final line.

guess that rules out silicone - never had much luck getting new
silicone to stick to old.

no pictures, don't know how to get a shot behind the tiles. ;-)

as for freak accidents, there are a few freaks in the neighbourhood,
but I don't let them shower here.

tks to all.

R.

0 new messages